Видео

Didn’t have enough room to take out in 2012’mini base. Had to go through passenger wheel well. Spent about 20 hrs. Very frustrating.

gas cap tip is a good one and a first having watched about a dozen of these! what is the problem with opening up the driver side door? also, can I say I just LOVE that a female is directing a male - we need MORE of this!

Someone please!!!! I don’t have the plate that holds the clip in place!! Where can I find it??

Hands down best 5vzfe timing belt video out there!!

Well done! I've been trying to find out what the heck that quick release the the radiator hose looks like and this is the first video I've seen with a clear close up of it and how to release it. Thanks!

thanks a lot. worked perfectly. had to wait for 3 weeks. it came from france and costed me 8$ u.s.

Great video. I feel ashamed of myself after watching this video. Thanks so much

Would this also work for a mini countryman

Thank you so much for this video. Had to do this for my 97 civic just now, it apparently was very overdue to the point where even with the trans in gear it still wanted to roll, and I had to use a pen just to get to my parking brake button 😂. Job done, 9 clicks, thanks again!

Thank you so much.

I dont have the budget to replace the clutch yet. Can i still keep driving the car at least for 3 months or so. Its the only mode of transportation i have.

Great camera work! Great tutorial.

🤙🏼 Aloha from Kaua’i 🏝️ Talena! Everybody like and share! Sisters across the world unite!

Or....take that to a certified shop/husband. We don't need THAT brake job on the road!

You’re hired stop by tomorrow to do my brakes 😂😂

Torque wrench not a rachet

Please tell me you used jack stands

Those are flat head

Thanks for this video! My wife's washer pump might be failing but before I go down this route, I'll check the fuses and then the pump itself. Fingers crossed it's not the pump coz this job looks like a big PITA.

Does this work if you already have an aftermarket alarm system?

I did this on my 93 thunderbird LX and now my car wont start.

This video was instrumental in our teardown and reinstallation, very clear directions and super helpful!

Great video. Took about 5 minutes to change to new one. I have a 2003 Honda Accord. The brass piece was also on my old latch. It held the cable from my trunk key location. Too difficult (not enough room) to reattach. No need for it since the I can manually open trunk with release next to driver's seat.

You are so good at education omg I love this video

I have that exact same manual and I can tell you that for most of those lights the book pretty much just says "take it to the dealer or a certified technician". The only thing I did with it was look at the maintenance schedule then I never opened it again, the cars take care of themselves if you take care of the maintenance items. Not trying to hate on this video but the manuals only tell you what the manufacturer wants you to know as a consumer

Great channel. I consiered doing the same content but the reality is Most people are too useless and lazy to learn to do tings themselves

Successfully replaced my son's 2024 Honda accord mirror. This video was a great help.

This video was beyond helpful, thank you so much! I did go into it thinking it would be easier, and I did have a bad day lol.

Do we really need a RUclips short explaining this? Our society is doomed…

Nice work! To get the rotor screws off, i put spacers and washers on the two bolts nearby and then tightened the lug nuts down on them. This helps relieve some of the pressure off the screws. I used a ball peen hammer to hit the screws. It dented them in somewhat. Then i took the impact screwdriver bit that was a phillips with a flattened off tip and hammered it into the screw and it stuck in there. Then used a needle nose vise grip wrench to clamp down on the bit. Then by hand turned slowly and eventually got the screw to move and come out.

I’m a Toyota technician and right now don’t have access to TIS you just saved my ass! Thank you for such well made video

Nice video. It's great to see a woman sharing her knowledge of cars and helping people out. Just replaced my trunk latch after watching your video. Not bad at all once you've seen someone do it, so thank you. Also nice to see women helping out other women. Good for you. Many thanks!

I done that on my CRV last week they figured it out they stuck a stick through it I'll be changing it from the female threads being on the base of the shifter mount to now be on the actual shifter hopefully this prevents them from being able to shift it

Great Info and video

Amazing! 🤯👏🏼👏🏼👏🏼

Where can I get that one bolt you had to replace from?

The exact second I hear the voice I skipped. Might as well have read a book on it

Awesome video

Great

Hi, very good video

thanks for this video ma'am...☺️❤️❤️❤️

Great video Talena!!

So glad I saw this - hooray for you!

Awesome video, but can you please advise how do you remove the brake dust shield without removing the hub? Thank You.

Seems easy 😊

For reinstalling you can use a paper towel BETWEEN the socket, and the head of the 12mm bolt. It'll lightly lock it into the socket head. Then the socket extension could be used as a hand held tool to start the threads. Greeaatt tutorial. Thanks!!!!

Great video. Next time I would put some anti-galling(anti-seize) compound on the rotor retaining screw instead of Loc-tite. The retaining screw is only there to keep the rotor in place until you put the wheel on. Once the wheel is installed the clamping force of the wheel against the hub holds the rotors on. By putting anti-galling compound on the screws instead of Loc-tite, it will allow you to remove the screws next time without an impact driver. I do this on all my Civics (EK, EJ, FA5). It makes pad and rotor changes a breeze. Hope this helps you next time.

???? Uhhhhhh odd.. just finished the book and specificwlly says not to do this w adding... why not between the min/max????

How do you fix that problem?

Your instructions so awesome