- Видео 7
- Просмотров 6 231
Jerome Ramirez
Добавлен 25 окт 2013
I teach chemical engineering process modelling in university, specifically the use of Aspen Plus software.
Aspen Plus Tutorial 7 - Biomass Pyrolysis
In this video I show how to model a biomass pyrolysis process. Biomass pyrolysis is proposed as a base conversion process for producing chemicals, fuels, and power from biomass. This shows how to model an RYield block in Aspen Plus.
This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
Просмотров: 907
Видео
Aspen Plus Tutorial 6 - Biomass Gasification
Просмотров 8188 месяцев назад
In this video I show how to model a biomass gasification process. Biomass gasification is proposed as a base conversion process for producing chemicals, fuels, and power from biomass. This shows how to model an RGibbs block in Aspen Plus. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
Aspen Plus Tutorial 5 - Rankine Cycle
Просмотров 2448 месяцев назад
In this video I show how to model a Rankine Cycle which is used to produce power from steam. This shows how to model a closed loop in Aspen Plus. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
Aspen Plus Tutorial 4 - Drying
Просмотров 3,1 тыс.Год назад
In this video I show how to model a drying process but quite differently. If you need to control the moisture content this is one way to model a drying process. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9. The method is loosely based on "Getting Started Modeling Processes with Solids" esupport.aspentech.com/S_Article?id=000064733
Aspen Plus Tutorial 3 - Solids
Просмотров 907Год назад
Here we model a biomass material in Aspen Plus using ultimate and proximate analysis, and its particle size distribution. This way we can model size reduction through a mill or grinder and a screen. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
Aspen Plus Tutorial 2 - Reactors & Heat Exchangers
Просмотров 179Год назад
In this video we look at modeling reactors via stoichiometry - a combustion reactor and simple heat exchangers to recover heat. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
Aspen Plus Tutorial 1 - Introduction to Aspen Plus
Просмотров 146Год назад
In this video we have a first look at Aspen Plus by working out a simulation of a compressor. This is a video walkthrough of Chemical Engineering Process Modelling course material using Aspen Plus V9.
How you give fractional conversion value ?
Not sure what you are asking about but you can specify the fractional conversion in RStoic specification. You can also change it via Calculator depending on the target moisture content as shown in the video.
How do I contact you? I would like to ask some stuff regarding solid process simulation.
what is your refrence for this project containing of Drying,gazification and pyrolis of this biomass?
@@بهناممصاحبی Hi, you can check my paper www.sciencedirect.com/science/article/abs/pii/S0959652619315331
Hello. thanks for your sharethis method of pyrolisis of biomass. I need to do a project for my course about "pyrolis of oil sludge' can you help me?
what is your base method for pyrolysis?
@@Dhivanka71 In this video I used Ideal because this is for teaching. However in my published work I used UNIQUAC. www.sciencedirect.com/science/article/abs/pii/S0959652619315331
@@jeromeramirez5989 i found this warning after input the UNIQUAC as my base methods STRUCTURE FOR COMPONENT CALCI-01 HAS NOT BEEN DEFINED. PCES CANNOT USE GROUP-CONTRIBUTION METHODS TO ESTIMATE MISSING PROPERTIES since, these warnings are for conventional components, could you please help me to solve this problem? thank you
how i input cellulose as a new component in aspen plus?
You can refer to this document to guide you. www.nrel.gov/docs/legosti/old/20685.pdf
Hey been having an issue with it but ive solved because of this video. Thanks keep the good work.
Could you provide a reference for the data?
The method used follows the Aspen solids reference guide. The data is from literature or actual data, I can't remember now, sorry. esupport.aspentech.com/S_Article?id=000064733
you are really good and your videos has improved my knowledge. i have a request, i want to design a coal dryer to remove moisture from wet coal, how can you help me, i already have the specifications for our coal and i want to do this one as my final year project.
Sorry for the late reply but the Aspen solids reference actually uses coal. esupport.aspentech.com/S_Article?id=000064733