Видео

Ae drone me vajan dekha

Pls give motor thrust angle in the motor spinning direction

Bhai not working why

Use biditional ESC it is easy to use

bro do you think it gonna fly, lifting is crucial. also you cant go right and left with it.

Os motores do meu giram em sentidos opostos quando eu acelero, mesmo eu nao movendo o joystick do yaw

In receiver diagram you showed positive and negative wires are connected with battery and esc positive and negative. But end off the video you connect battery only in esc .so my question is why you not connect battery with receiver ???

My esc are not connect 😢

What is the propeller size

Sir which battery did you use, etc information

Remote and receiver collaboration kayse karen

Mera remote or receiver connect nehi ho raha he please help me

Lol simple shit

Is there a kalman filter with this?

Je suis en train de chercher un récepteur avec 4 sorties pour 4 variateurs ou plus ou un récepteur avec 4 variateurs ou plus intégrés. On doit trouver cela non? Cela doit exister...Sinon, d'accord pour de la fabrication rationelle maison!

what wire did you use

Hallo bhi 4by4 bano

Like from Nagpur

Bro jal jati h 6s pr 12inch pr

This will not work as i have already tried 😂😂

Are bhai survo mother suply kaha se diye

Bro Code send please

Ye Bluetooth module ka kya kasm he....

What type of coreless motor?

The main problem is that plane is going left actually it is not the problem of radar(vertical stabilizer) first you remove your wings and put the finger in midle line of the wing and the wing should balance in this case it is going left which means wing is liittle hevier in left so balance it by adding some small weight in the right like (icream sticks)one ice cream stick is enough The flying is all about experience the more experience you have you can fly any unstable planes The experience come by crashing and rebuilding again again Also you use nrf home made transmitter so reduce the throw of elevator and radar by mapping the joystick values in program Elevator 70% -- 70%(upp and down) Radar 70%---70%(left and right) Also if your plane is going down when flying in 50% throttle just trim tge elevator to little upp position By reducing the throww off elevator and radar it will have a smooth fly Even if you are a begginer Also try to make a slow flying pusher rc plane That have a fish wing Like ft old foggy, ft explorer Actually it is all about experince

Whitch library use nrf 24

000 the horiz-stab and the main wing should be Parallel to one another.! it is not clear whether they are parallel.

001 the common stab root chord should be equal to about 2/3 of the main wing chord. poor design has resulted in stabs that are Heavier than they should be. it appears that the stabs should be located at least four inches nearer to the wing. when the model is level, the main landing gear should be located directly below the wing leading edge. 003 the amount of prop noise is excessive. the prop looks normal, so maybe the noise is actually coming from the nose. noise comes from vibration. servos do not like vibration; they glitch. you should, therefore, try to reduce the amount of noise/vibration. P-factor is a left-roll moment that occurs all the time, in a prop-powered aircraft. p-factor is the back-torque from a prop that is rotating cw. the affects of p-factor are most acute when a prop-powered aircraft is flying at a low airspeed, with the throttle/prop rpms high. this is one reason to NOT execute a left turn at take-off.!!! 326 servos do NOT go at the tail.!!! servos do NOT go at the tail.!!! servos do NOT go at the tail.!!! servos do NOT go at the tail.!!! googletranslate it should be understood that when a model is Defective, piloting includes a significant amount of Coping with the affects of those defects. do you understand that after launch/take-off, throttle should be Reduced to, say, fifty percent of max. at the end of the flight, max throttle and the elevator trim resulted in continuous climb and/or highly banked turn.

You should never operate a high power RF transmitter without an antenna. You will burn out the power amplifier.

Koi Mera ek project bna sakta hai ..

Capacitor kaha se liya? Kitne volt ka hai?

good work bro but I have many NRF24L01 modules but they don't work. Do you have any idea about them?

Well done bro 💯

Bro can we just use one Arduino as both receiver and flight controller ?

good job please arduino code

Dear how much is the range if antenna... as for me it is not working itbis only 30m

Rang kitna hai

Arduino receiver mein kiya 12v power de aakte hai bhaiya

And what's about vibration

Esse esc Caseiro Funciona Com Motor Brushless de dvd Rom

Made the best out of the resources huge respect

What the size of that adapter shaft?

What is the measuring device name?

Qual o tamanho do carrinho amigo?parabéns

My brother, make a video on how to enter the codes in detail, which version of the Arduino program, and how to enter the NRF24 library in detail. I am following you from Syria.

ye saare equipment ke price mention kar skte ho kya aap???