Видео

reminds me of the jetta front bearing. m14 bolts stupid idea. what blasting g cabi et you using g an what media walnut shell? sand? love to have 1 of them. I do the lazy electrysis rust removal. bucket of water soda crystals old battery charger and sacrificial brake discsleave it overnight or a day or 2 gets it to bare iron. then an hour tops with a wire brush on a drill then primer before it flash rusts

ah yes the m14 caliper carrier bolt that little bolt stopped me doing rear discs a few weeks ago refreshing brakes allround( i was on my back under a trolley jack) no stands no ramps no 2 or 4poster so left it for now hahah

Bro I’m converting my 19 Passat GT to AWD, manual, using a 04 R32 transmission and a 14 cc 3.6L 4 motion, the cc looked just like this so I took the haldex and subframe and everything else I ordered new I didn’t want to cut heat or fight with the rusted bolts

except for the spare wheel floor is the subframe just bolt on?

So talented 👏

Hello sir, is the rear shock absorber installed?

6:14 that dominos is coming 😂

Loooooks good for gun finish

Rah no face mask

Can't wait to see this on the road giving people problems

Roll yours out get mine in next 😂😂😂😂😂

Cor ! Get your surfboards out lads ! You could surf them runs .

100 brother nothing but ❤ number 1 🙏

🔥 🔥🔥🔥🔥🔥

I'm ready for mine🎉

Proud of ya brother 👏🏾👏🏾👏🏾👏🏾🔥🔥🔥🔥

Im doing same thing now but im using a diesel bkd140 mk5 4motion as a donor for my gti would be good to get in touch fr abit of info

if you have the R model on mk6 an mk7, this doesnt have any sense. And the perormance and handgling would be so so so so better than the mk5. In spain you have mk6 R from 15-18000, in USA it must be lower if possible

Randomly found your vid , I’m planning on doing mine if a donor comes up for the right money , and planning to video it

Awesome build!!!🔥🔥

Think you might have some coding to do mate.

Just a quick question....it not cheaper to buy a 4motion golf and change the engine? Rather than cutting the boot floor..

What year A3 and which engine in a3?

Will the down pipe not need to be changed in order to clear the prop ? Great work 💪🏽

Great content. Straight to work and explaining as you go. No long 5 minute intro of what's happening, then 5 minutes of work. Keep it up, I'm really enjoying this build.

Great work man 🙏🏼

Good videos, I’m working on converting my American model 18 Passat GT from fwd, to AWD manual. What’s your iG??? I may need some nice German parts lol

wider rear track is actually handy to have maybe just they alloys offset making it look wider slap a golf bbs on see how it changes

what donor car you used?

slight caster adjustment is needed haha

mad man ! getting hot and heavy at beastmode

Good luck sourcing the driver's rear right brake pipe, it's no longer available, the four plastic clips on the subframe are only available from a Skoda dealership @£3.15 each P/No S1K0611797 👍

Keep these videos coming loving the content.

Any jobss

ashman?

Following

Excited for this build 🔥

Can you do engine swaps?

Ea113 dead after 180k miles.. not bad 😂 what caused this?

curio to know the full braided brake lines v copper / or kunifer hardiness. curious as rubber /Teflon overloaded will flex slightly v hardlines don't also how tight are braided sat as I have once killed a (albeit cheapo braided 1 mounting it a bit tight pinching inner line with overboard. unit looks mega

Solid lad met you at c&c bowl

Read online that this conversion cost $40k+?

following build

Forever love the winch set up 😂

most a3 tdi quattro and s3 have alloy subframes. early r32 golfs are alloy subframe steel hubs/knuckles late steel subframe alloy knuckles (or visa versa a forgot

Built different this fella 😂

New engine or reman

Looks like shit

💪🏻💪🏻💪🏻

I blow my 1.8t engine number 4 went mashed everything