Видео

Nice, Thank you saved me some confusion.

Vise grips save lives 😂

That’s what l like to call a mechanic WaRLocK !!! 😂 Let’s Go

I just replaced both sensors and my thermostat and I unplugged my battery once I turned it on the code came back after j drove a couple miles and recommendations I don't know what to do at this point the car was never over heating but the light came on

The two small screws that hold up the pulley I I don’t think are going hold up if you have to lift a heavy deer

Ni cambiando el suiwtch ban a prender .esos hondas es un problemon🎉

Es mucho video para ese sensor.que ala mejor no prenden los ventiladores esos honda es un problemon🎉

i replaced both sensors and 3 fuses still fans wont turn on, fans do turn on when i turn on ac only. what could be the issue?

What is the part number for the bottom sensor?

Where did you get the gambrel/spreader bar?

Thanks Bro. Directions are horrible. Your video REALLY helped

For the socket, you can get ones which are specifically designed for tight spaces like this, where they have flat or hexagonal edges to grip and turn with a spanner. Not sure if that'll help. I used a similar such one for removing my motorcycle's front nut, which features a ridiculous giant hex-bolt which requires me to put a 20mm hex key into the hole, then put a socket over that, then have a foot long wrench to get enough leverage onto that using my body weight to get the bastard off. Don't buy chinese bikes.

Looks very similar to my CRV of the same generation, they're based on the civic chassis so hopefully the process is the same. I can't for the life of me find the top sensor

You had the hooks backwards when cocking. Just asking for trouble that way.

Thank you

The way you handled that ground wire was great. I definitely learned a new trick. Thanks!

Ty for the video. I personally mount a piece of treated 2x4 to mount the light to. Overkill but I think that increases longevity. I’m definitely guilty of over tightening which leads to a bigger hole 😂.

Dont follow the positioning of the spoiler in this video, its wayyyy too far back on the trunk lid. The top of the wing should line up with the trunk edge, not the bottom of the wing.

Could have been a min or two video.. Too much talking but thank you

Thank you for sharing. Where did you make the junction for wire running between the two posts? If you did it underground interested in what you used for connecting wires.

This is the best video I seen he explains everything so good some other people they just take out the sensor and they go OK here goes the sensor is already in stock but this guy he shows you everything love the video

was one sensor thicker than the other for u if so which was top n bottom?

that’s what i’m trying to figure out for mine. guy at the store told me it’s the same for top and bottom but my old top and bottom are different. i have 2010 Honda

the harbor freight $16 is a no brainer. I thought it was probably cheap but the pulleys with a brake and hanger are durable.

Thank you! All, please remember to give this person a like! Excelent presentation and effort.

I’d add a $20 hand crank harbor freight boat winch!!!☝️

Great video.

My temperature gauge stopped working but you said this one was for the computer. Is there another on somewhere?

Thanks for video, I will have to get someone to site mine in

Another code violation. Lights and receptacles can't be on the same circuit.

Thank you brother! big help!!!

Thanks for the video. I put mine together last night. I got it from Academy Sports and they did not have any extra 22 inch arrows so I bought a box of six 20 inch.

Dude how did you get the bolts in

Good video, gave you a sub, we need to help each other out on here.

Great video especially the tip showing not to have the gap when mounting. I had it then watched your video and fixed. Thank you! Also liked you showing how to cock the crossbow. Great video!

Very thorough. Talking about how deep to dig with variations of conduit and non-conduit.

Nice work man

Best video I found so far. Thanks man

Can I just solder it instead? But the wire for my spoiler is way too short so I’ll be soldering it with a automotive primary wire 12.2m conductor. I’m specifying it because I want someone to let me know this okay and correct to do

Would it be easier just to mount a crank on there than pulling especially for scanning because sometimes you just want adjusted a couple inches

Really enjoyed your video ....Today I just put together my new whitetail hunter str that I opted for with the illuminated scope and I see I ran into some of the same issues you experienced which made me smile to know they were shared! I also opted for the 400fps however at 187 pound draw weight it can be a bit of a workout for my 83 years so I will be keeping my Jackal too which has been good to me over the years. One crossbow is nice to have but two is even better for an old gun collector like me. Nice work take care.

Ton of help, I’m currently building something similar at my farm.

is this light supposed to be waterproof? Like can I install it in my enclosed trailer and not expect water to get around the seal?

Totally not to code. MC cable can't be surface mounted as done here - it's not protected from physical damage (see NEC 330.15). Mixing PVC and and MC as done here is not permitted. This does not provide ground to MC even though there was a separate ground wire run. Should the insulation on wire fail, the MC could become energized. Use of NM connectors rather than MC connectors makes this worse. Fundamentally, PVC cannot be surface mounted unless schedule 80 - again subject to physical abuse. Most AHJ's would require EMT for a pole barn.

You sound like Woody Harrelson!

thank you the vice grip was a good idea i never had any issue with the 17mm socket and rachet not fiting.

good luck on cocking it! i'm purty strong and i couldn't get it cocked!

Use a beer cup on the filter in the oil won’t spill

Great video man easy explanation and I’m new to cross bows this was so helpful

Fantastic video and instructions. As per space for 17mm : in Civic 2010 I had no issues at all . Very easy . In addition I change R3 relay because it was sticky. Thank you. You are the only one who said that this bottom sensor is responsible for starting fan. Mine was working when AC was on but did not start otherwise.