Видео

Is that a picture of your panel. 😳

👍

Great idea to use the very capable forklift to hold the camera instead of unloading the very top heavy, awkward compressor with it. Works much better as a 'triood' than a controlled lifting\lowering device!🤦🏻‍♂️😄🤔😂

this video enjoys. i like it

WHERE DID THEY GET THIS BOZO

You lost me at using a forklift for a table instead of a compressor lifter.

was wondering if this was going to end with a visit to the chiropractor... for future reference, lay it down in the bed, slide it out, and stand it on the ground.

THANK ALLAH FOR THAT TOWEL... jesus ... smFh

My brother, I'm glad to have found your channel, however, was the forklift behind you down for maintenance? Seems like a safer option for something of that size.

Why is this guy wasting my time showing how to put on gloves and use a spray cleaner? Please edit your videos!

This man is the best electrician in Florida the best

Keep Your Spirits up!

Rigo knows hes our electrican at our condo in Jupiter fl man he did some great jobs for us The man is only second to lightning Rigo knows

Thanks for putting this out there; it's very helpful. I have the same welder and had the same problem. I discovered that the big copper contact tab was bent slightly so that the center hole had moved away from the spring and the nylon end of the selector was sliding out of the center hole. I put the tab in the vise and bent it back just slightly so that the center of the tab was pushing more firmly against the spring. That's what solved the problem for me.

👍

Terrifying

God Bless them All❣️❣️🌟🌟🌟

❤stay unharmed

no volume.

What carb did you use I can find the manual of this 😅

Does anyone know what’s the part number on that copper tab ? Mine does not have the square contact tip

💪💪

Definitely faster than a shovel. Trust me on this.

350 or 250? I only ask because the wiring color is different in the 250.

Also your mic is not micing

Buenos dias hermano se puede soldar aluminio con ese tipo maquina Lincoln ac_ 225 saludo

I was having same issue.. thought it was maybe a broken wire inside.. took it all apart and wires looked good... come to find out after taking it further apart i found that the end that contacted the dial part to select current... the little tab was burnt almost all the off...i had some thick copper laying around and just filed factory copper arm to shiny and soldered the new tiny piece of copper to it so it makes better contact.... works like new again and getting full current to material....i bought this new almost 30 years ago.. been a great welder... thanks for the video!

I cant stop watching ! This thing is badass !!

The drive motors that you used were they connected to the wheels via a chain drive or gear drive ? And also are the controls just log splitter type ?

did you fix it. do you still have the lincoln 225. how does it work

Why don’t you keep your puddle moving instead of lifting off the puddle and then starting again?

Las dos partes conectar los cables y cambiar el selector

Hello friend, what a good video, thank you very much for your contribution. I congratulate you. Note that I have a Lincoln AC 225 GLM. Could you help me with the electrical diagram? It happens that you have several disconnected cables and the selector rotor is broken. I will be very grateful. Greetings. colleague

I noticed both your switches work very freely.mine is older than yours and the switches take a lot of force to move but my contacts likely need cleaning to as I’m having slight trouble with stick start

Sad❤ good patnt. JOB 👍👍

❓. GUSSETS NOT NEEDED ,, 2X2X3/16 ANGLE WITH 3 TAPED BOLT HOLES THRU ANGLE IORN ALLS NEEDED ,,, LIKE WHEN KID USED. (( COX GLOW FUEL )) IN YOUR B& S Lawn MOWER MOTOR OVER KILL... HEAT WORP ,,CANT REPAIR BOW & OR TWIST ,,

👍

Como saver si el transformador de maquina lincol esta quemado

I bought a [small engine] off this dude that thought he could put kerosene in the tank to help dissolve an unclog the fuel system, then left it sit for a couple years. It had totally turned to gel, gross.

Raw power.

Gator Watch! Beware!

Nice view my dude, Appalachia is sick.

Beautiful day...... can't see 30 feet ahead

Sir, those are Cobra chickens and they are not to be messed with.

when you run into rusty stuff, just grab the rod firmly and drag it hard across the rust till you get a burn, don't be shy about it. i have two of those tombstone welders, real classic equipment. 6011 rod will just about burn through anything

You should make a video about the whole setup with the hydraulic motors that’s pretty awesome

A little sloppy side to side and perhaps up and down.A machine shop or a lath could make a busing or tighter pin.. He is doing a good job though. The Hoffa joke just cracked me up.

Operator looks like an Average Joe and seems to be doing a pretty decent job.

Slowest Jig Saw in the World 😅

that's sick