Видео

You helped me fix my washer today !!!

How do you exit diagnostic mode?

That's the same washer model we own.having the same issue. God, I hope it's just a stuck sock or something. The wife is nagging for a new washer.

Thanks for the video. How did the socks get in there?

Mitch, I have a 500 version and want to know what tools I need and how to open it so I can fix the Anderson Plug that fell through to the inside Please help THANKS

Do most washers have that access point to the drain, on the bottom? I am having the same issue and was about to start taking stuff apart 😮

Very helpful!

These new washers are awful my family had a old washer from sears for like 20 years worked like a charm and she finally retired I'm on the second new washer and there's always a problem with them.

How the heck does a dock even get in there lmao

And I bet it sink I think that’s wat is wrong with mine unfortunately the person before me stripped the screws and I cannot open the panel 😩😩😩

Do you know what screw bit you used to take it apart? Updated to say: tamper resistant t-25

It's because its a Digital front load Newer washer.😁

Not 200$ exactly I charge for this 350$

hMM, i THINK I need a few mentors to keep me in line!! :)

Nice job! I suppose you've upgraded your system as this video was made in 2017. It would be nice to see what you've done with it. Solar is awesome...It has a part in the power backup plans at my home. I have a small 24 volt 200 amp hr system.

"I'll probably fix that later " ×10

You could at least disassemble completely and identify the problem. Oh I forgot..you don’t have a clue.

Thad castle hissing

It could be coin trap in front. Remove panel below front washer, untwist the cap and pull out debris and lint. Should start spin.

Kenmore W10280537A top loading ends with wet clothes, maybe 1/2 dry as usual; but, if do extra spin/drain cycle ONLY comes out ok as usual

Thank you i found a sock in mine.thks for putting video out

I’m super confused on how the hell that sock got in there. Why would the missing sock elves put the sock there? Rude.

Hi. Do you connect the circuit breaker at the battery level or somewhere down your installation? I got a pretty similar setup and want to connect a circuit breaker but not sure where to connect it. Do you have a blueprint of your installation ? Thank you

Great setup. I've ordered a 100w solar panel to add lighting for my work bench on my patio and also run underground wiring to my old shed for lighting to replace the overhead 110 wire. Also, intend to add a 12v ceiling fan above my work bench.

Did you check your cobb accessport? Sometimes the custom tunes just need to be remapped. I find stage 2 Husqvarna tune is best.

This is really cool does it work on leather

10/10 defensive technique, Randy Rand would be proud

If I could make a few suggestions. Place battery down low for service and heat place on plastic. Get a clamp on dc amp probe so you know what your draw is.dont mount everything directly on wood. last use wire numbers and make yourself a drawing. You have a good start underway you will learn lots. Thank you

How to do remove the pulley/wheel on this pump? Do you need a pulley-puller???

FPF antenna connector needs protection !

Cool video Mitch! What did you film this with, your Pixel2?

This is called a G ROTOR Type Pump

Thx for vid.

Nice, That's called a "Vane Pump" if you noticed, more than half of the movable vanes are NOT moving, they are stuck in the down position, That's why it stop working for ya..

uve put the props on the bloody wrong motor

Try turning the battery sideways. You have plenty of clearance then. I also had the same problem. I have the same receiver. I still have not had mine. Flying yet basically the things that peace of jaunK If I can figure it out, I'm just going to use the parts.

It flies better on beta flight 3.1 also I did the. WiFi mod antenna on transmitter to get rid of the dropouts

check Eachine Wizard setup video by Joshua Bardwell

In beta flight under the configuration tab set yaw degree to -90...that should fix your problem

how many channels is that RX?

Good vid Mitch, I had been lookin at this quad, I may hold off and look for something else if yours gave you this much trouble, you have earned subscriber 14

Hi Mitch. I need to see the pressure relieve valve assembly on this pump. I have disassemble mine and are not sure of the order to reassemble the pressure relieve valve(the big bolt on the side of the pump) Please if you can open yours and video it. You can e-mail me josny1964@gmail.com

Nice setup, I'm trying to get my working now. You might have explained why my wifi is always dying. I thought it might have been a crappy connection through the garage door. Thanks!

the little vanes sling out under centrifugal force and hold against the closest wall when spinning, they are supposed to be loose like that when not spinning

reppin' GR

Hi Mitch, question for you: I'm putting my 07 Outback PS pump back together. On the big roundish metal ring that surrounds the spinning pump vanes, I know the round metal pin goes on the side with the half-round hole, and matches up to the other half-round hole in the case, and that pin functions as a pivot point. On the opposite side of that is a little channel in the case. My kit provides a little stiff piece and a flexible rubber piece, both of which fit in there. I can't remember if one or both go in there, or in what order (should have taken pictures!). If I put in just the rubber, the round parts swings back and forth really easy. If I put the stiff piece in first and the rubber one facing the round part, it fits snugly, but the big round part moves very stiffly. Can't find a diagram or video with that detail, and no shop I've called actually rebuilds them, they just replace 'em. Do you remember how those go? :-) Many thanks, Eric

How much did you pay for the new pump?

and it looks like the problem may be that those little flaps that are pushed in when they hit the fluid chamber casing, aren't coming back out. Those are what move the fluid through the pump, and if those flaps aren't extending to the wall of the casing, then the fluid isn't being moved.

"...spins around, or something..."