- Видео 362
- Просмотров 2 267 191
Shane Whalley
Добавлен 14 июн 2013
Im a parts chucker, fabricator, engine builder, suspension designer, and basically a one man show of garage built race cars. All DIY, with minimal tools in a two car garage. ....with a lift in it.
Get some merch and support the build and the channel.
shanewhalleyracing.com/collections
Follow me on social media
Facebook: profile.php?id=573499614
Instagram: shanewhalley
Subscribe to my friends who help me do this stuff.
DaydreamHQ
ruclips.net/channel/UCIxkZkPuav1GzhKcOf-ieUw
Scotty Roddis
ruclips.net/channel/UCyytFfGEdK9m69id-kwkDyw
Michael Graham
ruclips.net/channel/UCpJoiv1UkI2_wo19KhRAG5A
Get some merch and support the build and the channel.
shanewhalleyracing.com/collections
Follow me on social media
Facebook: profile.php?id=573499614
Instagram: shanewhalley
Subscribe to my friends who help me do this stuff.
DaydreamHQ
ruclips.net/channel/UCIxkZkPuav1GzhKcOf-ieUw
Scotty Roddis
ruclips.net/channel/UCyytFfGEdK9m69id-kwkDyw
Michael Graham
ruclips.net/channel/UCpJoiv1UkI2_wo19KhRAG5A
Lets Talk About Wastegates
Follow me on Instagram at shanewhalley
Buy Garrett Wategates and Blow Off Valves
shop.garrettmotion.com/valves
Easy way to check spring pressure.
ruclips.net/video/8XTbvnoeahw/видео.htmlsi=eHzDaSfV6SB5BmcU
Buy Garrett Wategates and Blow Off Valves
shop.garrettmotion.com/valves
Easy way to check spring pressure.
ruclips.net/video/8XTbvnoeahw/видео.htmlsi=eHzDaSfV6SB5BmcU
Просмотров: 216
Видео
CAN YOU 3D SCAN TO PRINT, AND NO EXTRA STEPS? - Revopoint Pop2 test
Просмотров 763Год назад
Follow me on Instagram at shanewhalley
EP Auto $5K Shootout
Просмотров 242Год назад
Follow me on Instagram at shanewhalley Follow 👇 Cory Talaska at ruclips.net/user/CoryTalaska Brendon Greaves at ruclips.net/channel/UCMRrWZp6txPQTje17hDSOOA
Woodward 2022. The Only Entertaining Part.
Просмотров 5802 года назад
Woodward 2022. The Only Entertaining Part.
LS550 Gets Aligned And Corner Balanced.
Просмотров 4292 года назад
LS550 Gets Aligned And Corner Balanced.
Building The Cheapest 4” Aluminum Exhaust I Can.
Просмотров 9092 года назад
Building The Cheapest 4” Aluminum Exhaust I Can.
$25 Ebay HD Clamp? Are they even any good? Product Review.
Просмотров 7 тыс.2 года назад
$25 Ebay HD Clamp? Are they even any good? Product Review.
Finally Bought A House With My Own Shop!
Просмотров 8302 года назад
Finally Bought A House With My Own Shop!
What Is A PDM? Should I Buy One? Are They Expensive?
Просмотров 14 тыс.2 года назад
What Is A PDM? Should I Buy One? Are They Expensive?
The LS Swapped S550 Starts Up On The New Engine!
Просмотров 8522 года назад
The LS Swapped S550 Starts Up On The New Engine!
Dropping the LS into the S550 Mustang.
Просмотров 5542 года назад
Dropping the LS into the S550 Mustang.
Garrett G45 vs GTX45 Turbo Comparison
Просмотров 6 тыс.2 года назад
Garrett G45 vs GTX45 Turbo Comparison
Gridlife 2021: IT DIDN’T BREAK ON THE FIRST LAP!
Просмотров 4942 года назад
Gridlife 2021: IT DIDN’T BREAK ON THE FIRST LAP!
REPTAR! Nice to see you're doing so well.
really nice! What type/grade of 1.5inch hose are you using to go back to the radiator?
Great idea if your time has no value.
I was lookin for a review on one of these cuz im putting one in my 1j swapped supra also. Def found the right reviewer. #suprafam
A vehicle is a moving object. That's where the shrouding assist in front of the radiator. Your pusher fan does not "obstruct" the radiator more than a puller. Plus, the fan starts turning as you drive. If you "theoretically" find a marginal benefit puller vs pusher, then you face a bigger problem. I use pusher fans since 30 years on all my street cars which I build.
Keep it simple stupid
Sick video dude 😊
Dang I missed your videos!
I always thought gate size was more dependent on power being made not necessarily engine displacement. If you are flowing x amount of CFM for X amount of power then your gate needs to be able to flow enough of a percentage of that overall CFM to keep things in check , also in most cases your turbo back half can't flow enough cfm for the turbos rated power, so the excess CFM has to be provided by the gate. TLDR Gate size is better determined by flow demand not displacement. A 1.8l engine making 900hp will need more gate than a 5l engine making 500hp.
More volume than flow. A 2.0L engine turning 11k rpm at 40lbs of boost will need a larger gate than your standard 2.0L at 15lbs of boost since it’s moving more air. You can’t go just off power, because for large displacement engines that move a lot of exhaust without boost will need to have a larger gate to keep boost from spiking. There’s ways to go into technicalities for many different scenarios, I’m just trying to keep the video relatively short and simple.
Been a minute! I always love to talk about turbo components.
After 4 years I don't even know if you'll answer this but I'm running the 6.0 LS and is it necessary to keep the PCV valve hooked up or can I delete that by running a line to the catch can? This is my first LS build so I don't know if this PCV valve is necessary unless running a catch can. Thank you and yes these types of videos are awesome. Big Chief from the 405 is doing a lot of informational type videos and it helps us beginners out.
Delete it and run a vent to atmosphere style catch can
I have a RacePak Smartwire and either you are a genius or myself and the three people that I have hired separately are full tilt retarded, because no one can figure this out! Two people that I hired quit, and the other one said that the SW was defective LOL! And calling Holley is a total waste of effort! If you are interested in programming this, let me know! I'll wait! LOL
How did you end up getting the trans and everything to communicate with the bcm? I’ve got a 2015 and I’m doing 6.0/t56 and that’s where I’m at.
No BCM. Chassis is controlled through an aftermarket PDM, and the engine is on a Haltech standalone.
I should note that there is nothing of factory s550 electronically in the car.
I randomly had one single needle from what looked to be a needle bearing attached to my drain plug magnet yesterday when i drained the oil. Any chance that needle could be from my rockerarm needle bearing? I am scratching my head on this one....how could that have made it all the way down there without causing any catastrophic failures. ...??
I recently blew my 402 I'm thinking about a LS2. Any suggestions?
You think all the brand name companies have purchased a milling machine just to make clamps? They all get them manufactured in china and just get their logos laser etched onto them. All companies do it with products. It saves a heap of money on business overheads
Very nice, I like it. Do you think a setup like this would work on a car for endurance racing? Like for hobby drivers on a trackday where you drive for hours?
Looks like you had truck injectors. The kit had the right brackets if you were using the tall car style injectors.
can you weld in rivnuts? I've seen them in many european cars and 10, 20 years later the rivnuts have worked themselves loose.
Hey, you might not see this but would you buy it for a restomod. I plan on stripping out all wiring plan on adding additional luxuries such as power windows. But what could really take it next level is launch control, cruisecontrol, ... Would you ever consider putting it in an oldtimer when doing a restoration?
How can you take a man seriously that has ears like that?
Well done. I'm digging the sway bar. What an easy way using the pillow block. (Bearings)
What type of tranny do you have? And who built your drive shaft
Very nice man. Good job
What stall do you have on the torque converter
what size was the T fiting for the valve and an10 ?
Did this reduce a decent amount of weight ?
I’m trying to build a 900whp LS pro charger or twin turbo just need the most reliable/durable platform but I also want to run a 10 speed auto on it
I’ll be happy with 900whp reliable so I guess rated for 1800hp but pushing a safe 900plus if I want.
what size tube and what kind of pipe did you use? do you have a video of the front? were about to tackle bash bars on a 2000 gt
i miss seeing the gto but the new ride is cool to
It'll fit. Send it!
Don't think you can call that a bladder it's more like a tank in a tank lol
Check valve, check valve, check valve!
Cool
Good job. What did you use for tubing? Flexible rubber or is it lined on the inside?
I hope you keep going. I enjoy your channel and have for quite a while now. I've always said that I was shocked you didn't have more subscribers, but know that it's just because you haven't given it enough time. The only reason to not continue is if you don't want fame. The world is your oyster bro.
Been a long as journey o far
Love seeing my friends achieve their goals and dreams! 💪💪💪
I wanna do this mow
I was just gonna say weld a nut on top so u can put your impact on it. Good job
Ya boi is BACK ❤
Do a kickflip
How are your knuckles holding up?
Can you do a review from an ebay tial vs real tial?
What makes you know it’s fake?
Got a link
Bro what wheels were you running on that ls swapped stand? I absolutely need those I know you painted them white I want to do the same
Xxr 521’s
@@Shane_Whalley thank you bro
We are back BBY