Видео

Hey mate I’ve got a 5JJ R1. Any chance you can do a video about alternator replacements?

You have a patreon?

Whats a common symptom of a cracked liner? Low compression on #1 cylinder?

@47:25 ... Ducati recommends to move the tensioners anti clockwise.

Thank you

Nice videos man

F...timing i was almost cried to match upper and lower gears 😂

Hi, I was wondering if you would be able to reline and rebore a 1999 r6 for me, i will pay obviously but i have cracked liners and would like to get it redone

About to buy an R1 with a clutch fault similar to this with the splines...im gonna use this video as a guide.. Thanks

Hi, I see your a specialist in r6s, i am looking into buying a 1999 r6 with a liner crack on cylinder 4 and would love to buy and repair it due to the rest of the bike being very new, if possible could i have your email to discuss further?

Please do NOT waste time with drill bits.

How did it run with your 4 half turns out on each carb??

Where do you find parts for these bikes I have a 99’ yzf-r6 and want to do a full restoration but can’t find parts nor can I find performance parts as I want to upgrade it as well

Hi mate, nice work as always, I’m just rebuilding my 5EB at the moment, are the 5EB and 5SL head gaskets the same? Thanks.

Just found your vids along with just returning from hospital after hip fracture from fall after running out my door for the 3rd time to get on my 03 r6 and tripped. Pretty good feeling ill be educating myself during this down time.. Being unfit to ride after many years of not being able to either absolutely sucks. I'm forty in my first bike was an 03 in 03. Rode cpl yrs but Being back on one in the last couple months. Husband amazing because my knowledge is so much more. And i'm able to do appreciate the bike and it's just fun and it sucks Me rushing took it from me.. Anyways, can't wait to see what all you do.

Nice job as always

hi mate quick question sorry bud, while I'm looking on youtube, I put the R1 yokes on my R6 rubbs against the plastic of the air line will that get worse or just be a little like that?? i could keep the yoke on it the thread was on the top so have to thread it now lol

Just removed my 4c8 clutch to replace a broken selector shaft assembly and very glad I stumbled upon this video, cheers for the tips I was thinking it could be fun 😂 Thanks

The paid work you do in the garage you should video, earn out of that and earn off of.youtube, all bikers wanna see mechanical work being done

Hey! Where did you get that carbon tire hugger for the rear?

love the content bro

ive followed you this bike before, i spoke to you about the wheels I got 1999 witch you helped me with me putting on the R1 forks, well as for wheels I got a set of 2006 R6 wheels the rear fits straight on the front I had to put 3x1mm spacers on them then they fit also witch makes it look sweet :)

Always great to watch your videos buddy ❤

Hey man. I just found out my r6 has two bad cracks in the head. What would you take for one

fair play nice to see it getting getting built bk ive decided to keep mine so ile be in touch to sort something out for the conversion its to clean to let it go 😂😂

I rate the Goldfren pads really well, but I use the S3 variants

Love to see the 5EB's getting some love. I do miss mine. I currently have an FZR250R 3LN6 that I am slowly fixing up. Surprise surprise carby trouble, and then the swingarm bearings decided to sound like a squeaky bed frame. Never nothing to do!

Wish you nothing but the best. Great vids.

What do you set the float height to? They give a fuel level in the manual but f*ck that. There has to be a float height #

Not enough people have seen this to appreciate the effort

Great job, I'm going to have to watch this series again and closer. My 5eb is tired and I bought it neglected

Ive got a spare engine for my bike that i plan to rebuild in the future, though it runs fine. Leaving a comment for the algorithm, good work!

What did you set your float height??

Is a 2001 2002 Yamaha R6

My front cluster keeps on burning my CDI box up is a short in the front cluster and I cannot find it I ordered a cluster but it's the wrong ones I guess it's from a newer one it has one extra pin on it I tried to change the plug but have the last one but I don't know how I got it right or not

Hey I love the video bro I have a question I have the same R6 as u do my is 2001 my speedometer is lose on my bike I need to remove my front fairing and lights to get to it the screw under it but I've never done it before cheers

Hey man, do you know what to set the float height for the 5eb carbs? That fuel level is bs. A float height makes sense

What did you set the float height too??? The damn manual only gives fuel level...

Your r6 clutch cover video helped me out big time. Thx brotha still took some messing around put works mint now. 👌

Thank u so much Jon u are a top guy ❤

If your lucky someones done the mod on the second gear or put an 03-05 transmission in it - I had the detuned FZ6 with that engine, and second gear was worrying - I sold it straight away losing a bag of sand on it. Robbing Sons saw me coming.

Good content John. Where’s the steering damper gone?

Hi I enjoy your videos but can you give more details on the 5eb to 5sl conversion is it only 1 mount that have to be welded and the rest is bolt on I'm following from south Africa

The shift fork of my FZ6-5VX system seems to be faulty. When it is in second gear, it easily switches back to neutral and then back to second gear instantly due to the continuous output. If I want to replace the shift fork, I need to disassemble the lower half of the engine?

Welcome back. I would like to see the liners being done and see the full rebuild of the rear swing arm. Or a restoration of the whole bike back to how it was when new. Good luck.

Hey man I have a question if I'm doing the transmission will I have to drop the whole bottom half with with the rods and everything

If you do reline a 98-02 model engine, do yourself a favour and drop a complete 03-05 improved gearbox into it, but I'm sure you know that

Welcome back mate. Love the R6's

ive just fitted the 2006 year wheels to mine to I looked online so many forums talk so much shit its unreal the rear fists are straight on the front you have to space the brake discs 4mm each and it fits just in case you want to know

i followed you for the r1 fork conversion on my R6, im trying now to convert the rear and front end to look like the 2016 year ish if you know anything??