Видео

Your skills set is impressive. Is there anything you can't fix?

If when you are trying to remove the cap on the reservoir side it starts to untread from the bottom? How do you hold it without crushing the thin aluminum tube?

My bleed screws/bolts on top keep leaking, recommendation ?

Have a Vevor ice maker and noticed that it's virtually the same product just rebranded. $300 ice maker cant even last for half a year on the stock pump. Glad I found this!

Ah, the good boys of summer 😎🏊‍♂️

So glad I found this! Ours just died today. Your description of the issue was EXACTLY what ours is doing. Ordering the replacement pump to now will get this fixed up once we get it!

Beautiful Dog!

Looks like the same deseign as the $500 GE Opal ice maker. It was Chinese junk too. Not a good one on the market.

Good video man keep it up!

Chops

Pretty dog❤❤❤

he is swimming away from the 80s hair rock!

That is the first time I’ve ever seen a dog without putting his nose in the water and over his mouth 😅he was so cool😂❤❤❤❤

I miss my Rottie... anytime i see a Rottie in a video & no Vick brothers, it's an automatic 👍🏾!

He’s waiting for you to be the alpha and lead, you goofy

I think this is the problem we are having on our drivers door.

You sure the tensioner it is the best?

Beautiful Rott!

cool video dude, looks great!

Gorgeous Rottweiler and beautiful pool, I'm super jealous especially on these hot days lately

I wish you would have shown how to get the sides off…. For the life of me I can’t get mine off

Could you add a buy link to the motor DM45DS-20/14, can't seem to find it.

I'm soldering quite a bit as I'm fixing whatever I deem worth saving from the landfill. What I'm recommending is that you use solder flux. I like the paste though you need to warm is up with the tip to soften it. Twist the braid then dip it in the softened flux. Insert yout shrink tubing if you got some, otherwise use some tape later. Then dab a bit of flux on the solder terminal. Now make hook or make contact both items. Dip your soldering iron tip in the solder paste and melt a little solder on it. Then apply the tip to your joint. It should not require more than 2 seconds. Check that the joint is strong by tugging gently. Then cover the solder joint with your PVC insulating tape or heat shrink tubing. Voila! Easy-peazy!

You didn't mention which side the red wire faces on the pins, is it the back pin or the front pin. Thank you

The red buttons are to remove the dust canister and cyclone for better cleaning. You should do it every 3-6 months only use a damp cloth. Also the filters that came with your unit are washable. I would not throw them out if I were you. To clean the top filter correctly I would remove the see through top with a flat head screw driver to clean it out better. You’ll be shocked at what you find in there, lol. Don’t forget to let them dry for 24-48 hours. Thankfully you got the extras to use in the meantime. Don’t forget that using the vacuum on “Max” damages the battery cells quicker.

Wish you had posted this a year ago. We had something similar happen to ours but just purchased a new one. Guess we will never know.

А стружку из газовой камеры убирать нужно

The kid dancing around 3:22 was priceless.... Rock on!

Beautiful table, thanks for sharing. Would never make fun of Buc-ees shorts.

Your audio capture would benefit from using from using a lapel mike (remote mike) instead of the phone/camera mike.

Laws of Physics - that made me laugh. Even better, if you turn on CC, torquing becomes twerking… Thanks for the video.

I'm enjoying this process. It's cool that you can involve the family and making an heirloom that can be passed down.

Bottom looks beautiful. Can't wait to see the finished table.

Excellent video. Im about to service mine.

Great video! Thanks! I’m in Houston too. And have the same problem on the same motor Drivers side rear stud. Do you wanna take on fixing it for me?

I’m glad I found this video! Thank you for your help!!

Just did this on my twenty year old liquid cooled diesel Walker. Was shown by a mentor all the in's and out's of the jackshaft, bearings and collars. #1. If you emery cloth and clean where the bearing fits into, you won't need any special tools. #2 Old shafts will have wear and cause vibration and will take out new bearings. Always replace the jackshaft when doing the bearings. If you feel the jackshaft housing after running it you will feel heat. That heat wouldn't be there on a new jackshaft. #3 The center of those collars are offset and to tighten them correctly there is a little hole where you pound with a dowel, opposite way that the pully turns. This tightens the bearing in place with the collar. Then tighten allen screw. Nice video! I've always fixed my own stuff. If you've got a dealer like I got you avoid him at all cost's!!

What is the Amazon pump model or if you may have a link thanks

I would like to know how much are the bearings I swapt a hole jackshaft assembly it was almost 300.00. They are expensive and know pullies come with it.

Great video, I'm was torn between the Crown and the Dorman. This is the first video I've seen with the Dorman. I think I am leaning that way since my heat shield is rusty and needs replacement. The Dorman comes with all the parts, shield, gasket and down pipe bolts other then the 6 manifold bolts. Thanks for making the video.

Thanks for the detailed video! I even went a step further and drilled a few small holes in the bottom portion of the cover, so if an water did get past my silicone seal job, it would drain back into the bin.

Do you remember the thread pitch for the IFP and for the cap on the reservoir?

We had this same issue with our JK, cost us a bit more that you state to have a dealer fix it... Is yours still shifting well?

So the problem was what?

Thanks for posting this update.

Great video, Love the way your kids help out.

Thanks for all the detail and taking the time to record this. Best video I have watched on doing this.

That is beautiful.

Where did you get that hook for the scooper? Was looking for one but i can't find it. Thanks in advance - Andy

Thank you so much for making this video and your prior one showing how to replace the pump. I just ordered a Vevor ice machine that is pretty much identical to the Gevi and will now know how to replace the water pump and fix the leak if it happens