Видео

Thermo-magnetic vs electronic-magnetic CB. Is the only difference a processor verse the bi metalic strip? I'm assuming the electronic CB uses a solenoid as an electromagnet for contacts much like the thermo-magnetic CB, right?

Oh my word. That was beautiful. Fairchild GCFI chip is made by Onsemi. That is cool.

Wow, EXCELLENT! As an ER physician I’m trying to learn some wiring basics and when I think back on the number of electrical injuries that I’ve cared for, from the beautiful patterns of Lightning ⚡️+ Human Skin ➡️ “FERNING” (Lichtenberg Figures), to the savage Explosion / Charing of High Voltage Injury, as when >600+ Volts are involved. I wish that I had learned the hands-on basics of electricity sooner as it would make the receiving end better understood. ⚕️🇺🇸

This is outstanding. The internet has finally given me hope again. Rather than all searches leading to an Amazon ad, I finally got some info on my Neato. The one pat I missed or didn’t see was on the side brush. The side brush on my D7 is not working and I am assuming it is the module that sits above it as I have already replaced the motor. Would that be a safe assumption?

Thank you so much

Strewth, where on earth have I landed? This is pure gold! Thank you folks!

Noicr

in real world scenario like my work place, some variables can be added; rat, cocroach, spider, water drip and it manager shoes step on it...

Your RUclips video contents are very nice. But due to some problem your video views and subscribers don't increase. I can help you to solve those issues and problems if you want.

Congratulations, great technology and demonstration!

Those eyebrows are testament to the fact that Vulcans walk among us. 🖖

Great video. It would be useful at the end if you summarized the results of the various tests. Give some specific takeaways or rules of thumb based on your results.

wow super cool!

For 50 ohm at the scope end connect a BNC T adaptor to the scope input. Connect the bnc cable from the gen to one socket on the T piece and then a BNC 50 ohm terminator on the other T socket.

very interesting!

How about master and slave protocol ? How would thermostat gain access

Still doesn't make sense. Demonstrate!

All capacitors should be cooled or chilled to improve on capacitor capacity.

Please so a Rexing v33 teardown next!

Thanks for this. I had to tear down my dot after it was infested with bugs. This video was very helpful.

Hello Mr. Martin ROW and Hello Mr, Mike Schnecker , Greetings from Germany a beautiful video thank you, warm greetings to Prof, Robert Aumann ( Tel Aviv - Jaffa, iSRAEL ) Have a nice day ( ❤je t´aime 💙 California ❤) bonne journee 👏👏👏👏 👍👍

thanks u made our project easier

I wanna see how u disassemble it

Wow. Such an informative video! The hosts make it even better

Wow. The advances in technology are amazing. Shame about the radio mic interference. lol

I had a perfectly good robot toy. Disney has pulled the app. Garbage now.

High quality and most underrated video

ELSFP LOL Acronym... seriously...

these batteries scare the crap out of me - I'm will avoid recharables as much as I can!!!

It's EXFO.

For what is the yellow cable at the battery? Can not be for balancing when loading, because it is only a 3,7v battery. I had a dead battery in it and chosed it with a 800mah battery (Molex plugs) for the Hubsan 107d drone. Fits perfectly in it. Original in the robot is 1400mah. I soldered only the red and black cable on the original plug (red/yellow/black), which goes at the platinum. I didn't load it with the port on the R2D2. At the right back side from R2D2 is a back cover, under this, where the one screw is. There I made a opening for the plugs. You can easy disconnect in this opening the plugs and load the battery. After the battery is complete loaded with my Sky Charger D100, I close the hole with the original cover with his fastening brackets and nobody can see the difference from a R2D2 with the standard battery in it. Now I have more control over the battery. What the status from it is and I can chose a trickle charge, if I do not want drive with R2D2 a long time. If the battery is bad in a few years, I take simply another one in and R2D2 is happy again! NOTICE: For all people which will make that too with her own robot, this MOC is only for accomplished hobbyists. You risk a fire damage!!!!!!

One explanation for how the device can falsely create a figure is not an explanation for why stable cameras pick up figures or why those figures can intelligently interact with investigators. I claim this debunking is debunked.

Led telivision systems DEGPD5100B smartphone apps inbuilt

Oh, you know.... just "2000A Sine waves up to 10MHz". Nbd

very cool

Prostitutka ozin kangip jurip bireudinaitpa

Brilliant, you should have many more views.

thanks, great

Thank you Martin for the interview!

👍

👍👍

Nice information. 😎 Thanks.

These two are simply reciting (far too rapidly) from a script and probably know little about electronics. Still interesting to see the innards.

LEDs are really bad for your eyes and health.

Was a youtube video of 360 kinect a ghost was playing a kinect game

Wow. Just found this. My company uses Sigrity and like you pointed out the licensing restrictions are just insane. So much so, that noone really gets to learn anything about the tool because someone else needs to use it. I would love to see a comparison between this tool and Sigrity. It looks awesome. Great job guys.

FR3 is a somewhat undefined frequency band between 7 GHz and 24 GHz. The consensus seems to focus on 7 GHz to 12 GHz, 15 GHz, and 16 GHz depending on who you ask.

The company is pi-radio, and NYU Wireless spinoff

This demonstration took place at the October 2023 6G Symposium in Washington DC. It simulates a cellular base station in an Open RAN environment.