- Видео 183
- Просмотров 81 081
underground workshop
Великобритания
Добавлен 10 мар 2022
DIY big and small projects, how to videos and review videos, camper van conversion project, restore, reuse
Disclaimer: These videos are intended for entertainment and inspiration. Tools can be dangerous.
Disclaimer: These videos are intended for entertainment and inspiration. Tools can be dangerous.
small narrow shelving unit for workshop
#diy #diyprojects
small shelving unit with narrow "worktop" for workshop :-)
onnce again video with shelving and like usually from scrap leftover and thing already in possesion
two shelfs form old template (18mm plywood) another shelf - off cut of old coffe table (20 mm MDF) finally last top shelf from 9 mm buffalo board ( VW Crafter floor?) .All atach to steel frame (1/2" square section , 3 mm flatbar and 20mm square section ) Frame on adjustable feets made from bolts and washers .
small shelving unit with narrow "worktop" for workshop :-)
onnce again video with shelving and like usually from scrap leftover and thing already in possesion
two shelfs form old template (18mm plywood) another shelf - off cut of old coffe table (20 mm MDF) finally last top shelf from 9 mm buffalo board ( VW Crafter floor?) .All atach to steel frame (1/2" square section , 3 mm flatbar and 20mm square section ) Frame on adjustable feets made from bolts and washers .
Просмотров: 299
Видео
reclaiming parts from old valve oscilloscope
Просмотров 35821 час назад
#diy #vintageelectronics reclaiming parts from old oscilloscope I bought this old scope as a wreck , missing knobs, missing power supply module , and missing all valves. In addition traces of sparking inside. I decide to breake it for parts . lets check how many usefull parts we can get to use them in other projects. Local Elevator by Kevin MacLeod is licensed under a Creative Commons Attributi...
VAN TOUR DIY ducato campervan
Просмотров 14514 дней назад
#campervanbuild #diyvanconversion #campervanconversion short diy ducato campervan VAN TOUR
selectest restoration
Просмотров 10221 день назад
#restorationwork #vintageelectronics restoration of 50 years old multimeter. Selectest super 50 Mk3
ducato rear door lock replacement
Просмотров 407Месяц назад
#campervanbuild #vanconversionproject #ducato replacing rear door lock in my ducato campervan of course it will be same with all sevels, boxer, relay etc. Nearly completly how to tutorial. And like usually detailed, long and boring :-)
DIY test leads holder
Просмотров 41Месяц назад
DIY test leads holder nothing new but such a holder (why not hanger?) usually made from plastic cost around 20£ for short section , when you need 3 pieces it adds to 60 £ ! i made myself from aluminum shallow c- channel offcuts forget about peg board :-) Local Elevator by Kevin MacLeod is licensed under a Creative Commons Attribution 4.0 license. creativecommons.org/licenses/by/4.0/ Source: inc...
ducato cab door card removing
Просмотров 801Месяц назад
#diyvanconversion #campervanbuild #campervanbuild if you want to insulate a bit cab doors or repair something inside always you have to strip doors , remove door cards/panels and not breake too many things on a way :-) In this video stripping ducato/boxer/relay cab door, removing all door cards, sound deadening and insulation full tutorial, long and detailed
how to upgrade ducato reversing camera
Просмотров 73Месяц назад
#diyvanconversion #diyprojects #vanconversionproject upgrading ducato reversing camera, this camera combined with third breake light is realy low quality, means low quality picture (at least in my case ) lets try to upgrade it to AHD camera. I bought cheap AHD camera on ebay and will try to fit it into this combined housing and hope picture will be better
"moroccan" candle lantern conversion
Просмотров 13Месяц назад
#diyideas #diyprojects #diy "moroccan" style candle lantern conversion to 12v led bulb
fridge magnet board for campervan
Просмотров 542 месяца назад
#diy #campervanbuild #vanconversionproject so caled "fridge" magnets is a nice item :-) but usually in stell van is no place to place it . We already carefully cover all metal surfaces :-) with carpet and wood :-))) no no choice we have to made something special
how to shaping tracks for tambour door DIY
Просмотров 602 месяца назад
#diy #campervanbuild #diyprojects how to shaping tracks for tambour door by yourself? sound easy but is not in video few tips and trick showing proper direction :-)
DIY bench for home workshop
Просмотров 732 месяца назад
#diyprojects #diyideas #diy DIY bench for home workshop , from begining to the end. steel frame welded from 60x20 ERW sections with reinforcements 20x20 worktop 18mm plywood starange shape with cutoff corner -hence 5 legs Trick how to mark and cut angled joints in case of rectangle sections
TIG aluminium welding for very beginers
Просмотров 1222 месяца назад
#diy #diyworkshop TIG welding for very beginers, better to say few very usefull tips from beginner to very beginers :-) nothing magic in aluminum welding but on beginning is really hard in this video few usefull tips which can make your lerning curve stepper.
diy campervan water management panel
Просмотров 363 месяца назад
#campervanbuild #diycampervan #diyworkshop diy campervan water management panel. let's say final touch :-) final assembyly of let's call it water management panel inside diy ducato campervan conversion. quite a few videos concering this topic on channel and today final (almost) bellow links to previous videos with waste water pump and water lever gauge ruclips.net/video/s2ftkZuyoDQ/видео.html r...
DIY airline for home workshop
Просмотров 5023 месяца назад
#diy #diyprojects #diyideas DIY airline for home workshop, simple and small, compressed air distribution system for home workshop. like usually make on budget
DIY Shelf Silicone Tube Cartridge Storage Holder
Просмотров 2533 месяца назад
DIY Shelf Silicone Tube Cartridge Storage Holder
campervan grey water pump electrical connection
Просмотров 403 месяца назад
campervan grey water pump electrical connection
how to plyboard edge banding with heat gun
Просмотров 2814 месяца назад
how to plyboard edge banding with heat gun
lidl tyre inflator test umk 10c2 for CAMPERVAN
Просмотров 2834 месяца назад
lidl tyre inflator test umk 10c2 for CAMPERVAN
how to replace air filter in ducato 2 3
Просмотров 975 месяцев назад
how to replace air filter in ducato 2 3
led clock aluminium enclosure - build from junk
Просмотров 626 месяцев назад
led clock aluminium enclosure - build from junk
how i built water level gauge using LM3914 and connect it to chinese water level sensor
Просмотров 1847 месяцев назад
how i built water level gauge using LM3914 and connect it to chinese water level sensor
good and bad ideas of electrics controls campervan build vlog 77
Просмотров 927 месяцев назад
good and bad ideas of electrics controls campervan build vlog 77
camper simplest water and waste level gauge and sensor
Просмотров 1547 месяцев назад
camper simplest water and waste level gauge and sensor
British made military oscilloscope, it has a NSN (Nato Stock Number) and the M.O.D broad arrow symbol. The bakelite buttons are very typucal, I have the same ones on mitilary radio equipment.
Yes its (it was ) hartley ct436 , before i get it somebody take out PS unit and all valves. I guessing that it was broken anyway coz inside was visible signs of spark discharing along delay lines and later i found few burnt parts
useless video you need to talk over the compressor noise se we can guage how loud it is and also have some sort of script so your not stuttering when trying to review this compressor
As a kid with very limited money, I also did the same to a lot of electronics in order to build circuits I wanted to experiment with. I don't do it often today, unless the stuff I am recovering parts from are difficult to find, or too expensive to justify buying new. The old Tektronix scopes have good parts values, but they still have bad caps that dry out or short internally. But the tubes/transistors still have value as do the majority of the other parts, just be sure to check and validate the parts integrity. But most of them, I restore and bring back to useful status. Those ceramic standoffs are quite valuable, and should be saved for use in special equipment! If you are going to use any of those parts, I would recommend a DE-5000 and accessories, as it can check everything, Caps, inductors, and even resistors, all with AC current, and at different frequencies! Good luck with your projects! My current restoring is for Hallicrafters amateur radio equipment, and some old surplus military equipment. I am waiting for parts to arrive for a 1960s Hallicrafters SX-111 Ham receiver.
thx for comment :-) for me it's just economic calculation old stuff+labour < buying somewhere else +100% :-) in case of this hartley ct-436 scope was mainly cermic standofs of course I dissasembly only things in very poor state re DE-5000 , im using Escort ELC-3131d
Interesting. Very nice meter
thx for comment when new in 1972 it has price 34£ :-) nearly avg.weekly wage now i paid for two of them 20£
What about sealer under the fitting to prevent rain ingress?
from what i remember all FAWO (but only FAWO) has its own seal kind of of dense foam
Hi, I've got a different issue, wondering if you had any idea, what can be the culprit. I have a Parkside polisher and witch the switch being in OFF state and the speed dial on the lowest speed, as soon as I put the battery in/on, it switches on at the highest RPM (whilst the switch is still on the OFF setting). Disassembled and everything is spanking new (it was used twice only). No obvious damage visible. Cheers.
good video mate
thanks for such a good opinion :-) but can be better like usually
Thanks i just used your advice to set up my 700. I am going to connect it to my cerbo gx too to use the 700 shunt to measure battery voltage.
Glad I could help
I bought one of these recently and I notice that the compressor kicks in about every 10 minutes. Just wondering if yours is the same or was I sold a dud. Also, when it's used as fridge only, how do you switch off the freezer? DOC
in my compressor switch on also quite often but definitely not every 10 minutes (?) its a common in these "special camper fridges" (also these much more expensive) just lack of insulation (definitely too thin insulation) BTW what you have on display ? switch fridge/freezer- kind of misunderstood from your side - no offence this kind of fridge (general design -nor about camper etc.) always have freezen compartment inside (like in olden days) and switching between fridge/feezer just change setting of thermostate i used as a fridge only take out "door" for freezer compartment and use it as a shelf ( but of course is little too cold there)
@@undergroundworkshop8278 Thanks for the quick reply. I kinda guessed that there might be an insulation issue. Mine doesn't hold it's 'coolness' for very long. That's why the compressor kicks in so much. Thanks again for your help.
recently i check my kick in, let's say every 20 minutes
Great idea, handy for inflating tyres on your car, bike, van and wheel barrow, good video
Thx for comment yes its handy :-)
dont buy one no good unless on hook up, drain your batteries, and crap customer service, buy cheap buy twice
Do mot get one of these. They drain batteries, only any good for hook up..I had an 83l of same brand and it drained 2 batteries in one evening without any other power on..buy cheap buy twice..
mayby faulty fridge ? im not remember how much Ah it takes for 24 hours but i have not such a problem .
Where did you purchase that base?
yes
God bless RUclips, just saved me a lot of swearing ! Thank you
thanks, BTW one of the best comment I ever read "god bless youtube"
Buenas noches mi Peugeot boxer es euro6 llevaría el mismo ? Gracias
Hi if we talk about ORION TR it will work even if you have smart alternator everything is ORION manual
Promo_SM 🌺
This is a great method thanks
thanks for comment
Hi, I did the same as you but when I turned it on the wires started to burn and smoke
hard to say , maybe you mix wires or maybe it was different fault (did fuse on consumer unit blown during orginal FAULT?)
No, the consumer unit fuse did not blow during the original fault. The angle grinder showed no signs of life. So I've decided to do like you. Simply two straight wires with a switch on the phase. But when I turned it on the wires melted and it made smoke, so I turned it off immediately. I then tried again adding a capacitor but it does the same. I thought the rotor might be shorted, I can't find any other explanation. What do you think?
i not notice your reply , why i asking about fuse -coz in most commen case of failed speed regulator always main fuse blow , but like you wrote rotor probablyis shorten @@sfossamani
Does it need to be wired or just Bluetooth connected?
AFAIK this display always has to be wired , but is a device called SmartShunt. it's connects via Bluetooth to the VictronConnect app on phone
Thanks for the review. Do you need to add a fuse when connecting this to a 12v fuse holder?
fridge has fuse(and fuse holder ) itself but its located close to the back of fridge -means in case of anything you have to pullout fridge to replace fuse :-/ two options first remove fuse holder at all 2nd I place much bigger fuse into fuse holder and connect to common fuse holder ruclips.net/video/Ont7VRu_t_Q/видео.html
Exactly what I was looking for thank you
thanks :-)
Excellent video, We are specialists in campervan shower doors offering a custom made to measure door options.
thanks for your opinion
I think there is something not taken into consideration here. The adhesive used between the plies adds considerable weight to the plywood. If you look at two pieces of plywood of the same thickness, one constructed of more plies will be heavier, stronger, and more stable. The plywood made with more plies is also typically of higher quality, with less voids in the interior plies. So, when using plywood to build a campervan, you can sometimes get a lighter overall result from using a thinner yet heavier and stronger plywood. More than anything, the construction method can affect the results. For instance, use of a laminate of 5 mm sheets with 3/4-inch XPS foam between them and epoxied 6 ounce per yard fiberglass cloth between the wood and the foam will produce a panel slightly thicker than 3/4-inch plywood that is less than 2/3 the weight of the 3/4-inch plywood, yet much stronger. For large vertical pieces, a half inch thick piece with 5 or more plies can often be substituted for a 3/4-inch-thick piece with 5 plies without losing any significant structural integrity while losing a little bit of weight. Also, when joining two sheets of plywood at right angles, a finger (or box) joint is very strong and avoids the need for a piece of wood along the inside of the corner for reinforcement. That of course is a tradeoff between construction time and weight reduction (plus the cost of additional tooling to make those joints).
fully agree with you video is just about weight of various ply/boards constuction is different and more complcated topic for sample weight of 15mm poplar ply nearly equal weight of 12 mm hardwood ply and 12mm hardwood give better screws retension 15mm poplar give better board rigidity
@@undergroundworkshop8278 I would be interested in your experience in this area.
just ask :-)
Great video that mate. There’s always more value in a message that strives to teach and improve, than one which just tries to look smart and photographical
thanks for comment :-)
Thanks for sharing the video. I will be starting to build my own raised floor soon so this was very helpful to me. Thank you !
the most important is to keep level and flatness of main floor , in sevels chassis floor is not flat Regards :-)
Good arguments. Thanks for sharing. Cheers from Brazil
Glad you enjoyed it!
Do you think these would work in van that has remiss blinds installed?
hard to say easiest way -unclip remis and check if holes not colide with t pocket for blind, 2nd problem can be with bigger space between chassis and plastic
Cool idea!
lot of ideas lack of time :-)
From Canada: I imported Tambour Doors from UK for ma caravan build project, those pre-made straight tracks and corners are designed for 90 degree movement, in my case I needed some kind of elliptic shape so I had to have a plastic track CNC machined to achieve the final result I wanted. For your project, I am wondering if it could be better to groove the plywood walls using a router, following a template you could fabricate.
How many amps an hour?
to tell the truth i dont remember right know , but more then you can expect - if we talk about 24h usage- it was something like 30 (?)Ah for 24 hours in modest temperature , probably I mention it in video ruclips.net/video/qNjOD4xBINk/видео.html just insulation are thin like in all camper fridges
Genius!!! Simple ideas are the bestest 👏🏻
thanks for comment :-) I like to build stuff using not obvious things
There is an offset/calibration on both Victron and hall sensor. You need to use a good current clamp and measure the actual current and adapt the calibration till it fits.
The van is it a H2 H2 height and length
H2L4 H1- lowest has differnt door (lower) L4 is LWB with bigger overhang
This is genius! Thank you.
thanx a lot :-)
What is the thickness of the aluminum in mm ? I want to build the same frame . Greetings from 🇳🇱
its imperial 1/16" in mm it will be 1.6 mm section 38mm x25mm can be smaller 38x18 (i get good price for 28x25) plywood is bonded and screwed to frame
epic van build!!!!
thx a lot for all your comments :-)
hahahah amazing
will be much easier if i not change project during build , on begining it should be with eberspacher hydronic system then i bought cheaper (truma become cheaper this year) truma diesel and i have make some changes in wiring
i can feel the chaos an frustration hahaha
thx :-)
Put some paper against the inside of the filler and rub it with a crayon, this will give the outline and exact shape to use as a template to cutout.
very clever, its like watching an artist at work, well done. lots of practice... I hope to be giving it a go in the new year 🙂
hi thanks :-) lot of practice but to tell the truth is not complicated if somebody explain how to do it and give few tips on first time . Its a veltrim non stretch carpet. From one side is harder to operate but from second , veltrim forgive more mistakes then 3d stretch. For me veltrim is better
Exactly what i need to do to my Parkside grinder.
How do you know which blue wire from the motor is the live? There are two blue wires in the video.
Hey, man thanks for the video, it encouraged me to do the same, and it works. Great job and many thanks!
Glad it helped :-)
I was using aluminized foam without the adhesive back. I expected the pre-spraying both the wheel well and foam would require me to work fast and likely end up with stuff stuck where I didn’t want it. And so I cut a section that would cover the entire flat part and glued it down. Then I decided on the proper width for the next piece, folded it up and cut and then sprayed the wheel well in that area only, along with the foam piece and glued it down. It turned out rather well. Although I have more joint lines, each joint has been carefully cut to match the next piece and the width was adjusted to make it the ideal width so it didn’t bulge once glued into place. I would never have though of this idea so thanks for the clip!!
Your voice would be much easier to hear if you turned off the radio in the background. I’m assuming that it’s a radio because who would be silly enough to play music in the background if you’re going to give verbal instructions?
thanks
Looks really good, have you got a link to the lights and defuser you’ve used?
according diffuser spec. it have to be more led per meter then i have but this 3mm led strip is not easy to buy bought of course in china :-) i should have somewhere links, i will try to find it today evening
1. WS2812B WS2811 RGBW LED Neon Rope Tube Silicone Gel Flexible i bought T0606 type (6mm wide and 6mm depth) 2. 3mm PCB Hight Bright 5M 2520 2025 SMD 168leds/m
Can you show what stuff you can put in the fridge? Size of coke bottles, hummus tubs, cheese slabs etc (not eggs they are kept at room temperature).
yes why not :-) keep eyes on channel
Thanks for this! I was wondering what the best way was. 👍🏻
you are welcome :-)
Pwm speed controller. Dirt cheap. Fixed.
It have to be PWM controller for motors working at least with 15kHz with cheap PWM controllers for LED lights motors are very noisy
@@undergroundworkshop8278 the cheap ones I use are aparantly 50khz. No noise
can u tell something about model, name etc.
Any recommendations on speed controller ?
Hello
welcome on a channel 🙂
i have just bought one of these fridges, and will be installing it this weekend in my old transporter van, hopefully all goes well, but i am going to renew the wires from the back of the fridge to the supply where my fuse will be located as i dont want to have to remove fridge if the fuse blows for some reason.
i did same thing,
means i fit much bigger fuse