Видео

I've answered this many times, Nissan NP300

Honestly can't remember, it was 2 years ago now, I think the bumper one is 32" and the roof is 56" maybe? Best plan is a tape measure, they only make light bars in a few sizes so should be easy enough to work out 👍

tint them with film, delete the orange inserts, hid kit.

No idea, I did it all myself

Mitsubishi shogun

its just an android 7 inch 2 din, simple enough to do

It's from a mitsubishi shogun lol

@@revolutioncustoms6894 what year shogun ??

Think mines better but it wasnt bad tbf

yeah ,that was stunning! very well finished, the camera didnt do it justice.

Have you tried this battery and it made the difference? Having a nightmare with mine atm so this might be the solution

@@jacobweeks3426 if you are getting the pistol stuttering when pulling the trigger (it’s either more likely the MOSFET or the battery), when it happened to my cm.135s a day or 2 after receiving it, I sent it back to patrol base and got a refund as the tech on the phone recommended me to switch it for a gas pistol (it seemed like they had a high volume of them being return faulty, felt like a bad batch to me). I re-ordered another of the same cm.135s about two months later from patrol base, and this one has been fine since arrival (a few months ago now). The only caveat to that is I’ve never tried this new one with the stock battery, I only use multiple of my own third-party brand 7.4v 20c 680mah lipo by atm (a french airsoft shop) Just last month, me and my friend both picked up the cm.132s lipo aep (one arrived not cycling correctly but it wasn’t a MOSFET issue and i was using my own battery, it has been replaced for another one under warranty, and no problems with it now) I’ve run mine with my aftermarket batteries, but my friend uses his with the stock battery and hasn’t had any problems TLDR seems like the cyma mosfet aeps have some teething troubles with bad batches (most likely bad mosfets, but could be weak batteries also) my recommendation is rma it and get a replacement, and order a new battery, 7.4v 20c mini deans by either ipower 680mah, atm 680mah, electro river 550mah

@@jacobweeks3426 I'm using that exact battery in mine (recommended by Taiwangun) and it works great. I use the AEP as a sidearm, not as a primary and the battery lasts forever.

Thanks mate really appreciate it, going to do another manga paint job on another car soon.

I don't promote on social media much, just sharing what we built for you all to see 😁

Thank you so much mate it's appreciated 😊 Ford anyone interested in the most outstanding Ford cars in the UK go check out MRM Speed Shop, you won't be disappointed!

Hi Rich, unfortunately our car is custom built from scratch, its not a kit, however our front wing is the original and has been cut and reshaped under the headlight for a cleaner look and we have incorporated a locating pin in the bumper so when the bumper is slid on it auto locates itself to the wing if that makes sense? there is bumper fixing points under the bonnet, several underneath and one each side behind the side indicator, hope this helps you out.

Thanks for the like, appreciate it, just took a trip over to your channel to check it out, very cool mate, you got yourself a new subscriber, look forward to seeing yours done.

can you tell me where you got the mini deans connector from

It will work mate, the mini deans connector is a pack of 5 from eBay and you put the pins in yourself in the kit, the wire on the dual code battery will need shortening abit.

@@revolutioncustoms6894 i one from another site and it didnt work due to the sizes, i figured that there is a lot more deans connectors than i thought. could you send me the ebay link? id much appreciate it

Hole saw through 3 layers, stainless tube insert just behind the rear heater system

@@revolutioncustoms6894 I actually got it done. I put it a little further back on the bumper but I love the way it looks. Plus my pathy shoots flames now 😂

Yes mate, any aep ones fit it, mine are for the cm127 which is the same as a challenger xp17 from eBay, patrol base sell them aswel as amazon, around £10-£15 for 100round capacity.

Be careful with general wear and tear on it with extended mags. I've been using one and now the mag has started not sitting in correctly. Like you load it, it clicks but then releases itself by half a millimeter or so. The result of this is no feeding unless you physically push the mag in with your other hand.

To the roof rails

Thanks alot, there from the Nissan np300

Hey i have a manual transmition r51 with a yd25ddti engine what is it you are looking for when it comes to information?

its from a shogun mate, modified to fit

265/70r17 no lift, slight mod to arch linings but there still in there.

We didn't like the fake aluminium crap Nissan put in all there cars, looks too much like a cheap taxi, each to there own, I'm sure yours look much better. Have a great day.

@@revolutioncustoms6894 I love the carbon fiber, dont get me wrong, but the way you applied it looks much worse. You could use the hydrotransfer technique to wrap those. It doesn't look nowhere near carbon fiber or near a decent wrap. You heated it too much

@@eddy.alexandru if you watch the video properly you will see it is hydrodip, hence its masked off and covered in water droplets, the carbon pattern changes due to the object being rounded, carbon weave only stays straight on flat surfaces, exactly why carbon is not always the best choice for interior parts.

@@revolutioncustoms6894 Okay, thanks. For me it just doesn't look good at 1:54

@@eddy.alexandru not exactly hydrodip company finish but considering it was dipped in a bath tub it came out ok in our opinion, lol. Highly recommend people having a go at hydrotransfers at home it's good fun and a great alternative if you don't have paint or vinyl experience, it also offers designs and finishes that are usually only obtainable with an airbrush.

Depends on the car, we get attached to some of them, thanks for your comment and glad you enjoyed it.

Thanks mate, yes it was an amazing day, I'd say your the star of this video "aron the movie star" haha, look forward to shooting with you again soon. Have a great day sir.