Видео

Someone that actually lube the brakes. Good job. 90 % brake caliper seize because old burnt brake fluid and water corroded inside of pistons. Bleeding brakes every 5 years will save you $$$ and headaches.

hello this is the only maintenance on a harley davidson street bob thank you very much

Dude thanks alot!

Nice video. Thanks for useful how-to :) One question what did you use on the hub (11:25) after cleaning rust with the wire brush?

Thanks for the helpful video! About to do this myself. Question: exactly what kind of grease is that you used? Just want to make sure I use the right kind that won’t deteriorate anything.

How much are they?

Hello we got our trans fixed and our car is also doing the same thing. It will drive for a bit straight away (like maybe a highway) then we come to a stop sign and try to exselirate from the stop sign it wont and then it revs and then kicks in. Mechanic who did our trans can’t figure it out.

I put the the sock on mine

Awesome filter

Do I need a socket wrench?

🔥🔥

How difficult was it tightening the exhaust to the headers?

Honda makes everything so difficult. I miss my Toyota.

where did you get the lil rubber isolators from? i believe the same thing on mine broke so now my top thinks its just always open

Like there are different types of “twins”. This is like a conjoined twin. Still, in the sense of logic, ‘Tis a twin turbo. 💯💪🏽🧐

where in fl r u im in orlando with the same same isue

Anyone recommend a1auto parts???

Dude you are a legend. Need to do this and hate having 10 different vids to pull up

Needed this Video, good job

Great video, my motor or gears in that front are very loud, either need grease or replacement and grease. Will try this soon 👍

Don’t recommend compressing caliper with channel locks or c-clamp. Bleed those suckers to be safe. I put some crap into the hydraulic system which caused my clutch to start doing weird stuff.

I'm getting a code P0420 Below Threshold Bank 1. Do you know the location and part number. I have the same vehicle 2013 mks 3.7 base. Thanks for any help.

awesome video

Hello. Jak się sprawuje wymieniona półos GSP po trzech latach ?

Im about to swap my 09 SL transmission out wondering how yours is if you still have

Do you have the torque specifications regarding the subframe bolts, lower torque mount, and the steering rack itself?

Kind of a no brainer but make sure your crush washer doesn't stick to the oil pan. Mine has before so I just figured I'd mention it.

Service CVT EVERY 15k miles! Also make sure you buy some MASS AIRFLOW SENSOR by CRC and clean you mass airflow sensor and your air filter every oil change. Best of luck. I’ll only a Nissan car with a manual transmission. Unfortunately, their CVT’s destroyed their legacy of being one of the big 3! Honda, Toyota and…..not Nissan. We’re Mazda people now. Just won’t buy a Turbo Mazda lol or anything turbo for a daily driver unless it’s a Cummins diesel truck.

Have you never heard of a grease press before ? All you did was smear a little grease on them that ain't going to fly.

Thanks, will check tomorrow. Ours will rev, but won't move.

So you do not need to loosen the belt on the ac ? It looks like the bracket should come off without messing with the belt. That bolt is really on tight in mine.

Great video👍

These things are s$&@!!! My blades were zipped on so tightly during the factory installation that the nuts and spindles all stripped. Now I have to replace all the spindles too!!! I had to use pry bars and an impact wrench and could barely loosen them. The bolts to the spindle covers snapped in two and the covers themselves were broken at the eyelets!!! Never again will I buy a cub cadet! Hunks of f$&@!?&$ s$&@

I will remember this. Many thanks.

im looking at the same thing today and i dont see heat shields on todays version

Thanks man

super helpful. thanks a lot, man!

Your fuel cap is too tight

Hello. I could really use your advice. I am going to buy a 2020 Jeep Renegade 1.6 diesel automatic. The car has recently passed successfully the MOT inspection. The car consumed approx. 900ml. of oil from previous service until now (4.000km). I asked the MOT technicians if the car was leaking oil from underneath, would they be able to see it. They told me that they would able to see it as long as the car didn't have any protective aprons underneath. Watching your video I see that there is no protective apron underneath. Is this right? If you were checking the car for leaks, would you be able to see them in a Jeep Renegade? Is the approx. 200-250ml. oil consumption per 1.000km normal? PS. The exhaust fumes were ok. Thank you in advance for your help. BR, Vassilis.

Is this the same procedure for a si model

How many liters?

Sand is what wears them out fast

Need to get you lown mower jack would be easer.

Speed sensor.

I changed my spark plugs, changed the mass flow air sensor, and throttle body and my Nissan versa barely accelerates which sucks someone help.

You're lucky. I got #2 cylinder misfire. Tried everything....still misfire. These things are garbage. Nothing but issues. DO NOT BUY A VERSA

Just did this in like 20 minutes. Ty for your easy to follow video. Definitely made the job easier

Glad I watched your whole video. When you started with four quarts I was like it takes five. So I'm glad I watched it all the way through and you ran it to warm it up. Then added the 5th quart.

Do you have any fitment issues? I just recently installed mine in my 2020 street bob and the brake arm will hit when the exhaust is getting hot.

Great vid, but too bad the whole door panel wasn't in frame when you took it off. I don't suppose you have another vid that shows that? Thanks!