- Видео 25
- Просмотров 100 305
VUT - Engineering videos
Южно-Африканская Республика
Добавлен 5 фев 2019
Vaal University of Technology - Engineering Videos
Видео
HOW TO DETERMINE THE INPUT RESTANCE OF AN AMPLIFIER
Просмотров 9495 лет назад
Guideline to the procedure needed to determine the Input resistance of any amplifier
HOW TO CONNECT THE COMMON EMMITTER AMPLIFIER ON A BREADBOARD
Просмотров 6 тыс.5 лет назад
How to connect the Common Emitter amplifier on a breadboard
HOW TO CONNECT AN OP AMP ON BREADBOARD
Просмотров 41 тыс.5 лет назад
Procedure and guideline to connect an op-amp on a breadboard
HOW TO CONNECT THE COMMON COLLECTOR AMPLIFIER ON BREADBOARD
Просмотров 18 тыс.5 лет назад
How to successfully connect the Common Collector amplifier on a breadboard
PRACTICAL 4 UNBALANCED FEEDBACK CHARACTERISTICS
Просмотров 6865 лет назад
Unbalanced Cable characteristics using a pulse generator and resistor with a DMM
PRACTICAL 3 VECTOR VOLTMETER EXPERIMENT
Просмотров 1 тыс.5 лет назад
Cpmparing 2 cables with a Vector Voltmeter
EAMET4A GENERAL VECTOR VOLTMETER SETUP AND CONTROLS
Просмотров 6135 лет назад
General Vector Voltmeter used with Measurement 4 labs
EAMET4A MEASUREMENTS 4 PRACTICAL 1 EMC MEASUREMENT
Просмотров 4505 лет назад
Measureing the EMI of RF harmonics for a simple RF transmitter Electronic Engineering labs
ADVANCED SPLIT POWER SUPPLY SETUP
Просмотров 9485 лет назад
Advanced split power supply set up Electronic Engineering labs
EAMET4A FARADAY CAGE
Просмотров 1895 лет назад
Faraday Cage demonstration - Blocking RF with a door! Electronic Engineering labs
BASIC POWER SUPPLY SETUP
Просмотров 1,6 тыс.5 лет назад
Basic single power supply set up Electronic Engineering labs
13 AUDIO GENERATOR BASIC CONTROLS
Просмотров 2,6 тыс.5 лет назад
Simple Audio Generator Relevant to all electrical and electronic studies
11 BREADBOARD
Просмотров 2,9 тыс.5 лет назад
Simple BreadBoarding Relevant to all electrical and electronic studies
3 OSCILLOSCOPE CHECK REFERENCE AMPLITUDE,TIMING,TRIGGER AND
Просмотров 4,3 тыс.5 лет назад
3 OSCILLOSCOPE CHECK REFERENCE AMPLITUDE,TIMING,TRIGGER AND
9 DIGITAL MULTIMETER MEASURING RESISTANCE
Просмотров 1,3 тыс.5 лет назад
9 DIGITAL MULTIMETER MEASURING RESISTANCE
6 DIGITAL MULTIMETER RESISTANCE,VOLTAGE & CURRENT MEASUREMEN
Просмотров 1,2 тыс.5 лет назад
6 DIGITAL MULTIMETER RESISTANCE,VOLTAGE & CURRENT MEASUREMEN
1 OSCILLOSCOPE MEASUREMENT AMPLITUDE AND TIME
Просмотров 5 тыс.5 лет назад
1 OSCILLOSCOPE MEASUREMENT AMPLITUDE AND TIME
fara final..rezultat? unde este?
Great explanation
This must be for beginners....
please can i contact with you😊
Panchoda chlya ee ni jhot marna ee
Which op-amp did you use?
741 general purpose op-amp
ruclips.net/video/IOWBzwuNXaw/видео.html&pp=ygUJNzQxIHNwbGl0
Amazing thank you.
Nice video, everything is clear except how the positive , negative and ground ( green wire) connect to the power supply. I have a power supply with positive and negative output so it’s clear how the first two power connections are made . Not sure where to plug in the green wire 😢 unless it goes to earth ground on the power supply ? If so my power supply is no longer floating . Would be great if someone could help clarify how the 3 power wires are connecting to power supply in the video . Thank you so much !
Hello Greg, thank you for the comment. I am using a "split" power supply to power this op-amp. This means that it provides 3 voltage points from the supply. RED = +15V BLACK = 0V (GND) and GREEN = (-15V) If this is not provided, the op-amp will not be able to provide any NEGATIVE output swings. To overcome this arrangement challenge, we can place 2x 9V batteries in SERIES. The top positive is taken as POSITIVE, the connection BETWEEN the two batteries where the negative and positive connect, is GND (0V). The NEGATIVE of the second battery is then taken as -9V to the negative supply of the circuit. 73
@@riaanzs4pr thank you Riaan for the clarification. I missed the part early on in the video where it’s indicated there’s another video which discusses the power supply set up. These videos are wonderful. I liked and subscribed to the channel. Super helpful with crystal clear explanations! Thank you 🙏
Also want to mention I just successfully implemented both circuits using same power supply configuration. Going to buy a couple of green wires for completeness :) so happy I finally got this working
thanks for such informative video how can i use op amp to convert voltage signal to current signal
Very helpful. Thanks!!
Very good explanation. Thank you.
Very helpful!
Amplitude Timing Triggering And measurement Thanks 🙏
Me another Steve and I say you spit facts keep it up you demonstration is crystal clear.We need your style please make more you will build fan base so quickly. Thanks 😊
Very helpful, thank you!
good demonstration! thanks
I found this video most useful, thank you.
So this is Not a baking tutorial
why did the bread yawn? because the bread was bored
Clever! ;-)
Thank u sir
Your videos are some of the best on youtube.. Why did you stop making them?
Hi Steve, we will make more this year, and thanx for the compliment
Pls give me the circuit diagram
Hi sir,is it a guitar amp,i am from south afrika and the reason i ask,i like toe play outdoors,but want to ask u sir,how to build a breadboard portable guitar amp for nice traveling like camping or so,can u help with that,thank you
Hi Puggie, the op-amp is used as a pre-amp for guitars. I made a class B amplifier for the outdoor public address that works nice and loud when I sing and play my guitar
Can you add sub in English ?
Thank you for this...........
Horrible accent😒
But very good explanation 🙏👍👍
@@manjunathakapilsharma I smiled widely at your comment on my accent - in 35 years of electronics and 23 years in teaching at VUT you are the first to tell me so. Big thumbs up to your honesty. Now you know what a South African sounds like
A true engineer and Physicist to be with a massive sense of humour , I love this guy... no homo, thank you sir for being you.
THANKX
nice videos thanks sir......
Thx