Видео

Does a callabrater come with the machine

Thanks , I'm sure you put weight drums in wrong way, smaller one with the bolt should be on open end. Did you try to measure lb?

How much does 1 unit cost ?

How much does 1 unit cost

But how do we know when it is time to replace a grip tape?

Would be nice if this were a video on how to actually string a racket, rather than just a video about a guy stringing a racket as fast as possible?

Badminton tension only 27lbs? 😢 that is bad

อยากได้ไม่รู้ไปซื้อที่ใหน

Do you know a place where I can buy the Linear Gripper Lever Spring?

What is the price range for A600

Is it more durable than the previous model or being touchscreen and more sofisticated it can have more "little problems" earlier?

But, does bouncing the ball on your serve count as one of the bounces

What's the difference between this and the Gamma X - 6FC machine? I can't decide between the 2! Which one would you recommend, i string 10-20 Squash rackets per week.

Same comment as many others. The legs don't stay locked/standing. I followed the instructions here and below on how to slide them into the horizontal tubes but the bottom line is there just isn't that much friction/resistant from the frame of the hopper to hold them in and prevent them sliding with any kind of weight on them -- like 70 balls! So the product seems useless. And there's no support. Seems like I either need to attempt to manually deform the corners of the basket like some others below or give up on it. Bad design.

I am very careful when stringing my rackets on the Gamma but the tension is never correct. It's always 4 or so pounds over. I pre-stretch my string. I use a level so I always know when the arm is in the correct position. I use the ERT300 to test the strings after the job and they are never correct. I want to do 37 lbs. I have moved the counter weight all the way down to 35 and get 40. I never push down on the counter weight. Any ideas?

Nice! Going to try this setup on my Airbender 13mm!!

AWESOME THANK YOU.

I purchased the XLT stringing machine last year. While stringing today, I noticed that a stick and a couple of springs came loose from the tension control unit.

One missing step: after you remove the old grip, the glue will be on the handle. Take 100 grit sand paper and clean up the handle, this will provide a stronger hold for the new grip.

What is the size dimensions of the box package?

So satisfying!!

Thank you Jensen! We appreciate your feedback!

that video sucks so bad

How do you string more than 26lbs for badminton?

Do you mean .5 grams? 5 grams seems like a lot of weight.

When I’m tryna tension a string for badminton it just keeps going and my string breaks so do u know a solution? @GammaSports

Well.... This is really a bad design, I had to bend the place where the "stopper" are. Is I dont do this, the legs can barely support itself!

My new machine is not stringing as t the tension asked

It would be helpful to have a revised video that has views of you wrapping it up close versus being like 15 ft away from the camera. Plus some explanations of when you want to replace the under grip vs over grip. Thx!

Does the machine pull on the knot to make it tight or do you have to tighten the knot by hand?

Is there a way to reset the job counter (settings function 5)?

my grip from this brand has no sticky side at all

Great

How can I buy A600 mounting system turntable

can this mounting system Be used on the Progression ST II?

Which machines are getting the new A240 table as standard?

Legends

worst camera shots ever

Also what is the f or m mean by the knot option

Can this machine mount to a stand?

thank you

the packaging says go to the website for instructions, and there aren't any, nor any links to videos. this one must be for experts, because you don't show any close ups, especially of the beginning and ending wrapping.

How do I get it?

if i want to set up for 55 pounds. which side should i look into to find it correct one.

I thought it was very easy to understand. Could have shown a few close ups of the process. I was a le to rewrap my paddle without issues and it works great

Thank you for posting this helpful video

Thank you, replaced my first grip nice and easy after watching this video.

I have an xlt machine but mine doesnt hold the string automatically when pulling it back like yours, i have to pull it back if that makes sense Any suggestions?

How much is this ?

Hi, I am missing the 4 plastic adapters that hold the frame to the stringer mounts, where would I get them in Canada and would you have a part # please and thanks