Видео

keep continue sir...upload video

Flat end Screwdriver underneath the solenoid will lift the whole unit off instead of bending the metal casing.

Elinize sağlık. Detaylı bir video olmuş...

Hello, Would you happen to know how to install the 8 aperture blades on the secondary assembly as they fell out when trying to fix the aperture

At 0:52, I was unable to slide the plastic shroud forward by hand. What worked for me: I slid the edge of my iFixit Jimmy between the plastic shroud and the black/silver-colored metal ring. By rotating the spudger away from the front of the lens, I was able to break the adhesive and push the plastic shroud forwards. Once I did this in a few spots around the lens, I could push it the rest of the way with my hands.

Very good vedio.and helpful.can u fix af mode 100-400 USM thanks.

Thank you so much ❤❤

Thanks

i have some fungus growing on that frontal element. Can I use this method to clean it?

Pless upload video u repair that flex cable. I need to. Learn

Hi Ahmed. Watched your video about dust in the front element of a Tamron 150-600mm lens . After being able to take off the front lens element I find there is a gap between the front and back lens element. Do you know how to take the apart to clean between them

That’s it? Why stop there and not take it apart more?

I Have the same issue...you taking orders?

There we no reason to have the lens cap removed from the front of the lens while doing the lens hood repair.

Muito obrigada! Funcionou aqui pra mim!

P r o m o s m ✨

Good👍🏼

Very interesting! Were you able to repair it? It seems impossible to me without spare parts.

Do you repair them???

Thekyu sir ji

Hi :) Sorry to insist, but it seems that you know so many things about Camera :) Best Regard can you please answer this question below ?

Hi, very nice job !!! I have a noticeable backfocus issue on my 60d (many Lenses all same result) and if i focus with live view its perfect. Do you know if i need to turn clockwise or counter clockwise to adjust and resolve back focus issue ? (I talk of course about the Three screws which adjut position of sensor with springs effect) The amount of back focus is about 2,5cm (1 inch) at 1m with EOS 35 IS USM, and pretty the same amount with all lenses (Tested with 70-200 F4, 100 F2.8 Macro, 50 F1.8 STM, 35 F2 IS USM) Best Regards

Did you replace the GMR sensor or did you just clean the magnetic strip?

Not a fan of touching the internals of the SWM unit without finger cots or gloves - especially without cleaning the mating surfaces afterwards with isopropyl alcohol - but good repair otherwise.

So... i need to dissasemble all that to clean my front glass? Btw thanks so much for the video!

Shortest route possible, nice!

Very nice video thank you

❤❤❤

Nice content.

Thanks for your video. I can see you are very careful with the disassembly which will help when putting back together. With the fungus, was there none inside the lens groups? So only on the back of the front group and front of the back group?

❤❤❤

❤❤❤

❤❤❤

i have 70-200 ii same problem.

❤❤❤

❤❤❤

Very nice

Do you just use the bare cotton swab to polish the sensor bar?

❤❤❤

Good video. I have been repairing lenses for almost 40 years now and it is good to see a RUclips video where someone actually knows what they are doing. Two things, when those encoders are scuffed that badly so there is a bunch of white power on it, I usually replace them. What were you using to remove the scratches? Lastly, connecting and disconnecting the main board will go easier if you remove the leatherette, take out two screws and remove the zoom ring.

Many thanks Kaleem.

❤❤❤

Bought a second lens about 4 years ago off a friend. I just had the pleasure of my second lens jam. This time I have play between 400 and 500. But it will not go down to 200mm. I tried repairing this second lens. I watched serval videos and it seemed easy enough. I did it all as instructed. But I cannot get the shroud to slide forward. So I cannot get to that one screw that think is causing the problem. What do you think is causing it not slide forward?

❤❤❤

Excellent work

❤❤❤

Thanks! Kaleem 📷

Faça um tutorial fazendo uma manutenção da lente tamron 200-500 di a08

❤❤❤❤

nice work!