Видео

Seized pump impeller / bearing. It freed itself without help. I think it might have a coil coupler

Seized impeller

Greetings What is the timing for the fuel pump tdc?

lol, not what you would expect.

some might have built that as proximity sensor or party of old Halloween thing

I think you are correct and it's likely to be a proximity sensor. Probably built by a radio ham. I can't see the circuit but if you were to give it to someone who knew about vacuum tubes, they could reverse engineer it. It's not a (long range) telecommunication antennae, because it's not mounted outside.

ham antenna ???

It measures the pressure difference between the floor boards. Maybe part of a security trigger to something. If the pressure between the floor boards change, so too does the voltage between the resistors.

To clarify, thats a vacuum tube and not technically a vacuum tube. Not sure exactly what the device is, but it is definitely old. Probably from between the 50s to 70s. What is the code on the tube? That should help determine what it does.

Really it’s just best not to buy a Dyson cordless if you want something reliable and will last.

I’ve rebuilt about 75 of these Ryobi batteries. I’d bet a quarter that if you did the following, it would have likely been successful: 1. Charge each of five cells (10 cells in your case) up to 3.2Volts or higher. 2. Verify the balance is within 0.2 Volts for all cells. If not, make them so. 3. Perform a B.M.S. Reset by shorting the RST pin to ground. (NOTE: Some models don’t have the reset labeled as RST, it’s called J1 and located next to the large T2 contact that pokes through the shell. You must short J1 to ground AND press the LED charge status button.)

These are newer type , not meant to wrap wire around screw . The screw opens and closes the wire clamp inside the " back stab". I like this style

Very stupid video

Do you know if theres. A fuel cut if switch on 924 i heard its under drivers seat

I absolutely hate it and this is not talked about enough. I didn't know until installed on my car. The sound drove me crazy especially cause it's a Lexus supposed to be quiet. This flutter sound is just killing me. Will be uninstalling these slotted drilled garbage... Never again lol what a waste of money and time.

does this thing fit in Pentair niche ?

Thanks Mike!

973 Ziemann Harbors

I was holding my breath Mike...scary but you did it. My plan is to pad with moving blankets and hire two of my moving buddies to help next month.

Hey get somebody to help you it only comes off and on twice a year. You can do $500 worth of body damage real fast.

look ok to me

It brings me tears of joy to see everyone else with drilled and slotted rotors saying the exact same thing. "Sounds like very thin playing card in bicycle spokes." That's my thoughts exactly. R1 Concepts rotors and pads. I guess I can live with that, it's the squeaking my semi metallic pads are doing that really drives me nuts.

How do you get this motor out? What panel needs to come off?

Every year the guy across the street helps me take it off and put it on. A stored in a rack. And keep a new convertible top on the car.

Lol I'm tired of it to thanks for the video

Did you come up with a solution for it Mike?

Sorry - those 70s Mercs are ugly ugly ugly. And as for that being a convertible - sounds like it's been messed around with. And 3 speed auto? Yeah, sure the thing's pretty torquey but not Mercedes' finest - just a smidge over 200hp from 5 litres? They got that from their 3 litre sports car in the 1950s. What is that, 60mph in like 8 seconds for, what, 15mpg? It sounds about 3000quid's worth

volume is awful

There is ANOTHER electrical REAR PUMP besides the fuel tank. Without that rear pump, there is NO WAY to get any fuel in this injection pump.

the black thing under the pach is a thermistor its for over heating lock out

Exact thing is happening to me, what ended up being the reason?

I have slotted only and when I drive I hear like a windy sound. Would that be the wind passing through the slots?

That's the temp sensor not moisture

why don't you have a seatbelt on in the first place tho

This is why we need the dislike count back

That’s pretty obviously it’s a seat sensor it’s the most effective way to see if someone is driving. No one drives without sitting. Not sure how this is dumb.

Dumbest video I’ve ever seen. Congrats bud.

I had over 20 cars from japan to german and american and every single one of them does this what is the problem are you going to drive while you are not sitting?

Just tested it mine doesn’t do that

every other car does this. now put your seatbelt on and stop filming yourself being an idiot

This is a dumb video. Every car from every car maker will do this. The warning functions based on a pressure sensor in a seat.

Also in Australia, if you have the rear seats folded down, and stuff on them, you can't stop it dinging at all except by taking everything out, doing up the seatbelts, and putting them back.

ill say this, those different color wires give more ohms or resistance in the voltage, this then changes the speed of the motor and that changes the fan speed. The different wires are used to control your speed. blower motors inside are the exact same way, different wires that change the speed normally you do high speed tap for ac and low speed for heating modes.

Do they make air conditioners for basement windows?

Actually pretty cool man nice job good idea

There is a process to cleaning area rugs.

I would suggest using a fabric cleaner, L.A. AWESOME is good, or Chemical Guys Fabric clean, CG Lightning Fast Stain Extractor. Agitating it with a brush or a drill brush attachment.

Oh jeez you about gave me a coronary haha