- Видео 9
- Просмотров 116 933
Tundra Time
США
Добавлен 24 дек 2021
Toyota Tundra Flex Fuel Pump Replacement 38 Gallon Tank - Updated Part# 77020-0C170
This is a 2016 Tundra with the 38 gallon tank and Flex Fuel Pump. The symptoms were hesitation and a feeling of misfires at low rpms under load and horrible gas mileage around 10mpg. The truck started and idled fine and had no check engine lights. After replacement everything is as smooth as the day I purchased the truck and I also had 15.2mpg on the first 140 mile round trip.
Fuel Suction Tube Assembly with Pump & Gauge
Part Number: 77020-0C170
Fuel Suction Tube Set Gasket/oring
Part Number: 77169-0C010
Toyota fuel pump remover tool
www.amazon.com/dp/B08Z32SY4M?ref=ppx_yo2ov_dt_b_fed_asin_title
Fuel Suction Tube Assembly with Pump & Gauge
Part Number: 77020-0C170
Fuel Suction Tube Set Gasket/oring
Part Number: 77169-0C010
Toyota fuel pump remover tool
www.amazon.com/dp/B08Z32SY4M?ref=ppx_yo2ov_dt_b_fed_asin_title
Просмотров: 162
Видео
Creaking and Popping Door When Opening and Closing - Door Check Replacement - Toyota Tundra
Просмотров 6136 месяцев назад
This applies to all makes and models. If you have popping and creaking when opening and closing your doors it's most likely either loose hinge bolts or the door check. The removal and installation is the same on most vehicles. You'll need to remove the door panel(plenty of youtube videos on this for every model car) and then usually remove the door speaker to gain access to the doorcheck. Here ...
How to Make Matte Black Powder Coated Wheels and Rims Look Like New with 2K Satin Clearcoat for $40!
Просмотров 6616 месяцев назад
Very simple DIY to get your rims back to new. Just clean really well and spray with the clearcoat. If you use 2K clear make sure to use the correct respirator. Here is the link to the Satin Spraymax I used www.amazon.com/gp/product/B017Y4QTVI/
Toyota Tundra Steering Rack Replacement - Front Differential Removal - Year 2007 - 2021
Просмотров 9 тыс.7 месяцев назад
2016 SR5 4x4 procedure for removing and replacing a steering rack or replacing the OEM rubber bushings with Energy Suspension polyurethane bushings. The OEM bushings will wear out eventually if you have oversized tires with a lift etc. and the rack will have movement. I highly recommend Coach Builder for his tie rod ends and rear shackles. You can purchase the Energy Suspension bushings on his ...
2016 Toyota Tundra Steering Rack Movement - Bad Rack & Pinion OEM Bushings
Просмотров 1,4 тыс.9 месяцев назад
Toyota calls for replacing the entire rack when these bushings go bad due to lifts and larger tires. However, Energy Suspension sells a replacement set but it’s an absolute nightmare to remove and replace. It can be done without removing the rack. See links below. Noise can be felt and heard at slow speeds when coming to a stop or turning. Also popping sounds when reversing w wheel turned sharp...
1999 EZGO TXT Golf Cart Complete Rebuild From Start to Finish in 5 minutes!
Просмотров 10 тыс.2 года назад
EZ-GO 6" Ebay Lift kit, paint, Ebay tires & wheels, floor mat, steering wheel, wiring, brakes and lights.
HP Stream 14 Upgrade - M.2 Hard Drive Upgrade via WiFi Port - Hard Drive Not Booting Fix!
Просмотров 71 тыс.2 года назад
Hopefully this video will help you on the 32GB HP Stream Laptops. Once you install the new M.2 SSD Hard Drive and load Windows 10 the laptop will not boot from the new Hard Drive. You have to install "Refind" and it will work!! Below are the links to make this work after you watch the video: BELOW IS WHAT I USED!! M.2 Wifi Adapter is called Sintech M.2 (NGFF) NVME SSD to M2 A/E Key WiFi Port wi...
Toyota Tundra 2016 - CV axle play and noise - Is this normal?
Просмотров 11 тыс.2 года назад
Trying to diagnose a sound that I thought was suspension related. I've had a slight "loose bushing sound" when coming to a stop. A clank/clunk when turning into driveway and passenger side goes full droop in suspension. Update: This noise could also be from your steering rack bushings going bad on 2007-2021 Tundras. See my video of movement and in the description I have links to parts and DIY f...
Toyota Tundra Suspension Noise Solved - Knocking When Turning Into Driveways - Upper Strut Mount
Просмотров 13 тыс.2 года назад
AutoZone part: KYB 5737 AutoZone HD Spring Compressor $200 charge but refunded in full when you return it
I remember doing my first one of these as a tech. I probably struggled to get that rack out of there for about 45 minutes. Now it comes right out. You sure made this thing look easy. Well done and excellent video.
Thank you for the compliment and comment. I see alot of people say they don't drop the front diff to do this job but that seems like a nightmare.
I have had the exact same issues not to Long ago first was fuel pump and just less than month was rack and pinion bushings. Also the fuel pump needs software update from Toyota otherwise with new fuel pump it will happen again. I have a 2017 Toyota tundra limited. Soon will have to replace driver side cover gasket is what is next. 😢
Everyone says "software" update but they are just resetting the fuel density readings for the Ethanol %. When the Ethanol % starts reading really high when using regular fuel it causes the extended crank issues everyone was having. This issue was not related to the extended crank problem that was common. This is just a POS designed fuel pump by Toyota.
I'm looking into buying a Tundra and this video has been a great help towards helping me with the decision if I feel like taking on someone else's headache.
Thanks for the comment. Check out my latest video on replacing the Flex Fuel Pump. Try to avoid getting an FFV Tundra if you can. Here is a link ruclips.net/video/B6jRlR8gbjw/видео.html
Harris Michelle Johnson George Moore Daniel
а вай фай тепер не працює )
Where do you buy this Wifi M2.0 adapter?
Did you search it on amazon?
@@justindees29 What the name of this adapter?
What size engine do you have. I have a 2010 Tundra with 5.7 and I am having an issue getting replacement in. I had to remove the input shaft of the old one in order to get it out. Does anyone have any suggestions for me. I feel I have to either lift engine up or remove oil filter housing but even then Im not sure any comments would be greatly appreciated.
This is the 5.7. Did you watch the full video? You have to remove the front differential to get the rack out if yours is a 4x4.
Thank you for posting this video. I have a 2wd Tundra so I was able to skip the diff drop, but the section on the hydraulic lines really helped me get over a hurdle. Bushings replaced, alignment done, truck is better than when I got it. (I bought it used with unknown steering damage).
That awesome new! Yes, the 2wd is so much easier lol. I'm glad the video helped.
How are they holding up? I have the exact same set of rims with the same problem.
It's only been about three months but they look great after every wash still. Definitely worth it for the low cost.
Just drop the cradle and that’s it
Wonder if this can be done with without removing the diff if I’m lifted 6”. I’d prob take the inner tie rods off cause it’s quick and easy, less hassle getting the rack in and out that way. But I don’t have anyone to help me do my work so I look for little things to help me lol. I did my full lift install alone, that front diff can be a pain in the ass. What works well is a motorcycle jack! I’m lucky to have one.
You sure it's not your FK uni-ball on the uca?
This particular noise was from the strut mount but later on my uniball ended up being lose in the socket on the UCA and Tuff Country replaced both UCA's under the lifetime warranty.
@@tundratime941 Yeah, in the video what kind of looks like? The uniboll was shifting side to side my long travel buggy had same issue
Man, first of all thank you very much, you are the only reason my Stream is still functional, I had never heard of Refind before. Still, I cannot manage to get it to boot without the USB stick. I've got Windows installed on the new SSD, the internal eMMC formatted and assigned a letter, I copied the EFI folder from the USB stick to the eMMC and it still doesn't boot from the new SSD without the stick inserted. With the stick inserted everything works just fine, but upon powering up the PC without it inserted all I see is a black screen telling me to install on operating system as none was found. How do you did you format the eMMC? How did you copy the EFI folder in it after formatting? Simple drag and drop or you used some tool? Also, what does your boot order look like in your BIOS? Cheers man
On power up start tapping the ESC key to Enter BIOS check and see if Legacy Boot is Enabled ( Default is Disabled ), if Disabled, Enabled. After restart and on power up tap F9 for Boot Order, if the laptop is booting fine from USB and not from the drives, USB may still be set as Priority Boot Device. Just a Thought, but in any case I am just under taking this Upgrade this weekend, I will have a video of my progress and I hope I have gathered all the information from all the videos I have seen.
@@BudgetBuildBarry Thank you for your response mate. After writing this comment I did enable legacy boot and moved the USB down in the boot priority order, but that didn't affect the problem. It's still booting fine with the usb stick inserted and not finding an OS without the stick. Something is preventing the rEFInd install on the eMMC from booting and for the life of me I cannot understand what it is. I'll be following your progress to see if we can sort it out, for sure! What exact model do you have? Mine is the ax011nl, the one with the N3060, 32 GB eMMC and 4 GB of RAM which I upgraded to 8 GB, and that works just fine despite the mobo documentation saying 4 GB was the maximum. Both the original and the upgraded sticks are rated for 1866 MHz, but they both run at 1600 MHz and there is no way to overclock it from the BIOS, which is already quite weird in itself: why would they ship a 1866 stick that only runs at 1600? Bah...
@@Vercingetorix45 HP Stream 14 ax030ca, the upgrade I am doing is battery swap (swollen battery 6 year old), M.2 to NVME Adapter, 480 GB SSD, WIFI/BT Dongle. Further mods down the road semi transparent keyboard with RGB around edge, and back cover the mirror section of HP Logo semi also with pulse RGB....maybe, I will have to get a friend to solder it up. As there is still room for a small control PCB for the RGB.
@@BudgetBuildBarry I followed your channel, I'll definitely stay tuned for it!
@@Vercingetorix45 Thank you!!I will try my best to get you an answer that helps you!!
Take the two bolts loose on the lower control arm for the love of God so you don't destroy all your brake lines and sensor wires trying to get those driveshafts out.
Looks like a hastle
Thats an understatement lol
Warranty void if removed (blah blah blah before it use it its already in the trash)
Thank you for the input, for same reason my laptop go on recovery mode, when format the old drive and copy the file in it. So I decided to keep the boot file in the U.S.B. ( a thumb size ) and go like that
That looks... So rustic
what is the blue gauge next to the key switch on the dash, and where did you get it? Cart looks really good, I'm currently debating on what color to paint my ezgo. The cement grey looks really good.
That guage just shows the battery level as a percentage 0-100% charged. I used a color chip book to pick the color and it's actually Hitachi Grey but it looks just like cement. Thanks for watching
Hi Thank you for putting this video. what was the part number and the where did you source the universal u-bolt joint for the steering column?
There is a link to the rack bushings in the description. Here is where I purchased the steering shaft www.ebay.com/itm/394742887206
Mine does the same thing. It moves like that. I thought that was normal. So I have to do the same thing?
Well you don't have to do it but if you're having a hard time with alignments or there are noises that are bothering you it's a good idea to replace them. In the description I have a link to the video of the entire process to remove the rack and replace the bushings.
What did you have into the rebuild?
It's been a while but I think we had about $3,200 or so into parts/materials. Batteries and wheels/tires accounted for $1,800 of the cost.
Question you said have the refind installed you mean on the laptop or have it installed on the flash drive ? Also was just wounding do I have to take off the 2 wifi cords to do this ?
The Wifi antenna can stay in place, you only need to detach them from the network card, they simply plug/unplug like a snap button
Get usb wifi adapter
I keep getting a hard drive not detected error after installing windows 11. Then it just loops back into the windows 11 installer.
Your control arm is hitting the spring.
I appreciate the comment but the UCA was no where near the spring during normal driving. It was the upper strut mount rubber bushing that was dry rotted as I show in the video.
Links please
Energy Suspension Replacement Bushings shopcoachbuilder.com/collecti... Steering kit shopcoachbuilder.com/collecti... Rebuild kit that I used (my originals were still tight after 100K miles!) shopcoachbuilder.com/products...
Yeah that's alot more involved for the average semi mechanic but great video 🙌
@@miztrusa lol yes it defintely is but it can be done! Thanks for watching
Was not able to make it boot from the new drive on my 32gb ax030am, but I can use the new drive to install apps. So I uninstalled as much as I could from windows 10 and am now reinstalling apps on the new drive. Kind of a janky way to get this to work, but it makes this laptop functional.
I’m having the same problem and I can’t get the refind program to download and be functional
Good video
Very impressive job! Excellent description of work required! Adorable golden retriever!
The golden is so chill......He slept right through the dropping of the rack, lol.
I don’t know why people insist on doing this job without pulling the front differential. It just seems like it would be so painful to do with the diff in the way. I replaced my rack and honestly dropping a differential was only about 30 minutes worth of work I couldn’t imagine trying to work around it to replace some bushings or something
Maybe because they don't want the diff to leak after all that work?
@@Paco53 It's easy and like I said at the end of the video just drain the diff before you even start this project. Then just refill at the end. This was my first time doing this entire project so I learned alot and I would be much faster and efficient the next time.
Hopefully there is not going to be a next time.. I bought my truck knowing it would need a new rack, I'm truly worried about this project, but I guess I will learn a New thing or two.. thanks for the helpful video
@@Paco53 Just follow my video step by step and you'll be able to replace that rack no problem! I'm here if you get stuck
Great video! I might have missed it but you I did need to remove drivers outer tie rod. FYI
Worked perfectly for me. Bought the wrong adapter and ssd. Windows setup won't recognize Msata drives, so I had to use an NVMe drive instead. A few important things to note is that when you format the old EMMC drive, you must use the FAT32 file system and legacy support must be enabled in BIOS. Took some troubleshooting, but I'm pretty sure this is what you need to do in order for this method to work.
Did you have to pull the rack? And did it fix the popping? Currently going through the same issue I think
I'm about to do this myself next week because no shops seem to understand you can do this without removing the rack. 4 wheel parts quoted $600 but they've never done it this way. They just replace the whole rack. Here is a great write up on how to do DIY www.tundras.com/threads/anyone-replacing-their-steering-rack-bushings-w-35s.61354/ Also, here is Energy Suspensions video but they made it much harder by not disconnecting the tie rod ends and not using a ratchet strap to hold the rack forward ruclips.net/video/2hNkvMiHbNY/видео.html
Ican change the wifi device and replace wifi to ssd nvm2
Just started hearing this on my 17 4.6 tundra this week. Thanks for the video
Welcome. See my video on replacing the steering rack bushings because this is a cause of noise that many don't realize. Have someone turn the wheel while you watch the steering rack for movement. At the end of this video I show the before and after ruclips.net/video/uvZyCfiFCzI/видео.html
As a follow up to this noise. The CV axles were fine and that noise is normal. Turns out the bushings in my steering rack were shot. See my video showing movement. Energy suspension sells a replacement set. Toyota calls for replacing the whole rack wtf!
Were you getting a popping noise when turning? I am and I suspect it’s my rack bushings but not certain
@@jamessteinbrook4770 This sound was not my CV axle and is my steering rack bushings. I have a video showing the movement of the rack and also links to Energy Suspension polyeurothane bushings. Here is video and description has link to everything needed ruclips.net/video/ypUKJIGiJNU/видео.html
On the new hard drive. Did you have to install window on it before placing into the HP stream. I am also having the same issue. Every time I re image the laptop and placing the nvme into it. On the device manager it show up the nvme but I am unable to use it. Can you maybe make another demonstration your whole process? I been trying to do this for few days now unsuccessful.
This worked for me. Model # 14-ax012ds. 32gb version. I used the first link posted and only installed Refind on the USB. I created Windows 10 install USB and changed BIOS to boot from USB first. Ran USB install and deleted all partitions on 32gb drive as well as 500gb drive I installed. Installed windows on the 500gb drive and when it restarted to finish setup, I removed Windows stick and installed Refind USB as well as USB wireless adapter. Windows finished install and I then let windows update install all updates and drivers. Once done, I downloaded AOMEI partition assistant and cloned the refind usb drive to the 32 gb drive. Then I used AOMEI to change partition size of the 32gb drive to 1gb, removed the drive letter and made it hidden. Lastly, took the remaining 30gb of the built in drive and partitioned as D drive. Changed BIOS boot order back and removed Refind stick. Now boots off the hidden partition and works fine. Thanks for the link.
Can you make a video demonstration that process. I am stuck at this for few day now. I am also trying to upgrade the storage space.
Yes pls, as hungson said, could you make a video of what you did? I'm stuck. I had Windows installed on the eMMC, I installed the new SSD in the PC, then like you did I installed Windows on the new SSD and I was able to boot from it with the refind USB Stick. Than I wiped the eMMC and copied the EFI folder from the refind USB stick to the eMMC and now I'm unable to boot from the new SSD, both with and without the refind USB stick inserted it just won't find it!
0:12 seat covers link please?? Thanks a bunch! nice setup!
It's Alea Leather. I had a shop install it for me but here is a website I found. It seems to be higher quality than Katskin www.touchupsautomotive.com/products/2014-2021-toyota-tundra-crewmax-alea-diamond-edition-leather-seat-covers-black
Hello sir What is the name of the piece that connects to the hard drive? Where can I buy it from, as it is not available in Egypt? What is the solution to the Wi-Fi problem after removing it from the motherboard?
use wifi dongle then thats the solution for your wifi problem.
Hi sir
thx
Awesomeness 😎
What hard drive are you using
Привет,мужик скинь ссылку на переходник на m2
I have 2 older ones. Can this be done on the hp stream 13 or 11. Found out my mPCIe Receptacle female socket connector for adapters are built upside down this days. Meaning that the flash memory will be heating up the chassis. Even though not certain if this adapters are the correct ones. Ugh Is a hassle and fire heating issues.. Wondering if this can be done on the older hp stream 13? Or is this hp streams of mine a door stopper recycle's!!
Hello, I can't find your video on how you installed hdd?
I have an HP Stream 14-ax104la laptop, where I formatted its hard drive, and when I start the computer, the caps lock button blinks with 4 long flashes followed by 3 short flashes. Can you help me correct this error? The computer screen flashes 3 times and remains black. So, it doesn't even let me access the BIOS. Any wise advice would be greatly helpful. Thank you very much.
Bro I had the same problem for 2 years, several times I tried to see what was happening but I couldn't understand what it was, about a month ago I started wanting to fix it again and it occurred to me to disconnect the battery from the bios, the one that is like the battery of a clock, and then the laptop started working again, only a warning appears when turning on but other than that it works perfectly, I hope it helps you
Hi and what about the wifi than ?
You use a USB wifi adapter
soo... why didn't you show how to open it?