- Видео 62
- Просмотров 147 268
Welding 2go
Канада
Добавлен 7 мар 2021
Welding & Custom Fabrication. Powder Coating and Custom powder coating Oven builds.
New layout table for the shop.
Wall hanging table. Great space saver!
#shopupdate #workshop #spacesaver #wedding #weldingtable
#shopupdate #workshop #spacesaver #wedding #weldingtable
Просмотров: 19
Видео
I Built a DIY Patio Ice Box for $120 (and it works GREAT)
Просмотров 758Месяц назад
#backyard #woodworking #outdoorcooking #icebox #patioideas
Outdoor barbecue station upgrade 
Просмотров 102Месяц назад
Making some shelving for outdoor barbecue area. #outdoorcooking #barbecue #woodworking #backyard
Custom heat coil mounts for powder coating oven. #powdercoatingoven
Просмотров 2,5 тыс.6 месяцев назад
Making mounting brackets for heat elements for powder coating oven build. #powdercoatingoven #powdercoating #diy
Powder Coating Oven control panel build . #powdercoatingoven #controller
Просмотров 2,2 тыс.7 месяцев назад
Powder Coating Oven Controller Kit. New powder coating oven build underway. Control panel build and set up. #powdercoat #powdercoating #powdercoatingoven
Honda GX 200 Clone build completed. part #5 #honda #hondagx200 #gokart
Просмотров 5199 месяцев назад
Installed the tank, clutch and jet the carb. Test run sounds great! #honda #hondagx200 #powerspot #gokart
Fear No More: Honda GX 200 Clone Spark Test Revealed Part #4
Просмотров 1599 месяцев назад
Install new custom exhaust and a 12v Rectifier Regulator and wire up the electric start. #honda #gokart #hondagx200
Honda GX 200 Clone build. Engine mount and custom exhaust. Part #3
Просмотров 3369 месяцев назад
Building an engine stand and a custom exhaust. #honda #hondagx200
Honda GX 200 Clone build. Install electric start and remove governor. Part #2
Просмотров 27510 месяцев назад
Install electric start , removed the governor and installed new intake
Honda GX 200 Clone build Part# 1
Просмотров 28210 месяцев назад
Customizing a Honda GX 200 Clone Installing electric start , intake, jetting the carb and removing the governor and a custom exhaust . #honda #powerspot #gokart
Tool Time….. DEWALT 20V Max XR Reciprocating Saw & Oscillating Multi-Tool
Просмотров 14510 месяцев назад
Replacing an existing tool and adding a new one to my collection. #dewalt #dewalttools
Dewalt tool repair doesn’t go as planned!
Просмотров 20210 месяцев назад
Dewalt tool repair doesn’t go as planned!
Tool Time….. Cylinder Compression Tester.
Просмотров 10811 месяцев назад
Tool Time….. Cylinder Compression Tester.
Making my Wife Happy! Table refinishing, sanding and stain.
Просмотров 10711 месяцев назад
Making my Wife Happy! Table refinishing, sanding and stain.
Great idea for shelving to create more shop space!
Просмотров 175Год назад
Great idea for shelving to create more shop space!
Tool Time … Inexpensive bandsaw stand. Does it work?
Просмотров 143Год назад
Tool Time … Inexpensive bandsaw stand. Does it work?
Shop organizing! Cleaning station and Dewalt battery rack. #Dewalt #Storage
Просмотров 117Год назад
Shop organizing! Cleaning station and Dewalt battery rack. #Dewalt #Storage
Plastic Welding: Saving the Day with DIY Repair
Просмотров 104Год назад
Plastic Welding: Saving the Day with DIY Repair
Re-plumbing the Shop Vac dust collection system.
Просмотров 153Год назад
Re-plumbing the Shop Vac dust collection system.
Spring maintenance and shop organizing to create more space.
Просмотров 132Год назад
Spring maintenance and shop organizing to create more space.
Tool Time. Tumbler vs Ultrasonic Cleaner
Просмотров 804Год назад
Tool Time. Tumbler vs Ultrasonic Cleaner
Honda GX160 Engine Tuning. #Honda#rebuild #power-sports
Просмотров 3,4 тыс.Год назад
Honda GX160 Engine Tuning. #Honda#rebuild #power-sports
Honda GX160 Motor Transformation Completed. #Honda#rebuild #power-sport…. Part 4
Просмотров 426Год назад
Honda GX160 Motor Transformation Completed. #Honda#rebuild #power-sport…. Part 4
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 3
Просмотров 549Год назад
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 3
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 2
Просмотров 912Год назад
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 2
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 1
Просмотров 987Год назад
Honda GX160 Motor Transformation! Complete rebuild. #Honda#rebuild #power-sport…. Part 1
Eastwood powder coating system in action! #powdercoating #eastwood #powdercoatingoven
Просмотров 538Год назад
Eastwood powder coating system in action! #powdercoating #eastwood #powdercoatingoven
Upgrade for the powder coating oven #powdercoating #welding
Просмотров 263Год назад
Upgrade for the powder coating oven #powdercoating #welding
Awesome oven! Does it take long to heat up such a big oven? Is there anything you would have changed? Thank you for posting such a professional video/build!!!!
Hi Darren , This oven takes about 25mins to get to 450F. I agree it is large but that’s what they wanted, they do lots of larger car and bike parts. If it was for me I would do half the size and more racks. Thanks for watching cheers !!
Dang, the majority of the wiring you didn’t show!! It was just all the sudden hooked up and “there ya go”…
… Would you like me to send you a wiring diagram?
Good content
Thank you 👍🏼
How many resistors are connected and how many watts are each?
There is 1 solid state relay and it is 40amp max @220v . I always try to stay under 35 amp for the complete system. 2 burners @ 4000watts each. You would need to use the right power cord and have minimum of a 40amp breaker .
I developed a dedicated controller with IoT capabilities, allowing users to remotely monitor and control various parameters
Please send me some info thx
why you are using single thermocouple. I think it will better if you use at least 2 thermocouple having probe length at least 6 inches and which controller you are using ? I made a dedicated controller for ovens having alarm and Timmer option
Hey thanks for your input. I’m using Ink-bird PID Temperature Controller for most of my builds, it also has these features I just don’t use them.
What controller are you using?
@@welding2go I made my own controller. Having feature to upload weight and temperature to the sever let me share you that
Great work. What kind of wire did you run for the oven elements?
Thank you! 10G high temp wire
where did u get that red valve cover
I powder coated it.
@@welding2go did you add the red from the inside too?
@@photoaxcel no just the outside
Looks good but I just used single gang electrical boxes….
That works 👍🏼
Awesome job!!! We’re did you get the glass from?
Hey thank you! Your local glass company can help you out. You would need high temp glass 5mm thick (ceramic glass) normal used for fireplaces.
@@welding2go thanks
would really love a list of control box parts and wiring diagram. Great Videos!!
Thanks Jim, message me on Instagram and I will send you a diagram. I will also send some links on what I used on this build.
a.co/d/fI3ug52, a.co/d/0WC102E, a.co/d/bwtLy0h,a.co/d/eEnpPmG Hope that helps, cheers!
Great video I need the same thing built my oven but lack the knowledge on control boxes. is there a list of what you used? or do you sell the finished box? Thanks my names Jim
👍🏼
Where did you get the micro jet bit set from?
Amazon , I’ll send you a link. a.co/d/hTcwhA5
A True Canadian right there.. always gotta have our Timmies handy!! ☺️
💯🇨🇦
How much you do you sell them for? The big one
The one in this video sold for $9200.00
I hope you go into detail with the wiring of the PID controller. I have a homemade oven fully constructed. I gutted a traditional electric oven and used that wiring harness for my build, unfortunately though I didn’t test it beforehand like an idiot and I found out that the controller was not functional. So now I am investigating the PID option but I feared that it may be a bit of a headache, and I wasn’t sure if it would work for my application. Seeing that someone else is using the same methods gives me some inspiration that it may work…
Hey good morning I definitely will be going into detail. In the meantime, if you would like message me on Instagram and I’ll send you a wiring diagram and see if that can help you out.
Turn your heat sink 90 degrees more for air flo
Thanks. I need the room in the panel. I’m hoping the fan will keep it cool.
What is the watts of your elements and where did you get them?
Hey good morning, the elements are 3000 W each to run both elements you would require a minimum 40 amp service. I have an account with a supplier, but you can buy something similar on Amazon.
@@welding2go ok thanks. I was hoping that you would have a link but I will search.
@@gbodyperformance I’ll send you one
a.co/d/2E6LkMu Hope that helps
sounds good, like what you did with the exhaust.
Thank you, I’m really happy how it turned out.
looking good!
Thanks you!
Like the Dewalt stand!
Yes it worked out well.
plastic welder worked great! Can you send me a link I would like to purchase one thx
Absolutely! 150W Plastic Welder,Plastic... www.amazon.ca/dp/B0BFL9P48N?ref=ppx_pop_mob_ap_share
How much was the stand?
$100.00 and it worked great!
Looks like a great stand!
Definitely worth the money!
Lots of work, looking good!
I agree, I’m always trying to make extra space in the shop.
Sir ji ovan ki heat roknye ke liye kon sa metarial lagta hai.। Or ye kabje kha se milenge.।??
Rockwell insulation ( fire retardant )
Are all 4 elements ran off of 1 plug? Like a range plug?
Hi Brandyn, yes all 4 burners ran off one plug rated for 50amps (not a range plug) Range plugs usually rated @ 30amp. Always check with a licensed electrician.
How long does it take for oven to get to temperature
Hi Zachary, this oven with four burners takes roughly 15 minutes to reach 450F. I also tested it with only 2 burners roughly 28 minutes.
Where did you get the mounting brackets for the heating element
I made them.
Happy New Year
Do u have the links for parts u used for the electrical n panel thanks
I purchase from a supplier but you can find almost everything you would need on Amazon. I will forward some link shorty thx
KCD4 Rocker Switch Power Switch... www.amazon.ca/dp/B07MMZ5SWG?ref=ppx_pop_mob_ap_share 10 Feet Heat Shield Fiberglass... www.amazon.ca/dp/B08N46GP4R?ref=ppx_pop_mob_ap_share BNTECHGO 10 Gauge Silicone Wire... www.amazon.ca/dp/B01M8M2SC4?ref=ppx_pop_mob_ap_share Inkbird Heat Sink SSR Solid State... www.amazon.ca/dp/B06WLNHPWK?ref=ppx_pop_mob_ap_share Inkbird Display PID Stable... www.amazon.ca/dp/B01LQ8TOYW?ref=ppx_pop_mob_ap_share mxuteuk 2 Pcs 12 Positions Dual... www.amazon.ca/dp/B086BRHN6C?ref=ppx_pop_mob_ap_share GDSTIME AXIAL Fan 9225, 110V 120V... www.amazon.ca/dp/B08GSD9VR8?ref=ppx_pop_mob_ap_share GE WB08T10002 Light Housing... www.amazon.ca/dp/B00M0YVBFC?ref=ppx_pop_mob_ap_share GE WB08T10002 Light Housing... www.amazon.ca/dp/B00M0YVBFC?ref=ppx_pop_mob_ap_share Mophorn 15Ft 50 Amp RV Extension... www.amazon.ca/dp/B07NMGBTT4?ref=ppx_pop_mob_ap_share BUD Industries JB-3958-KO Steel... www.amazon.ca/dp/B005UP9NCG?ref=ppx_pop_mob_ap_share
Thanks I greatly appreciate it
Happy Thanksgiving
Nice video. The voice level is okay but when the music is cut in the levels get unbearably loud. I can't watch the whole video. Wish I could.
I’m using a new video editing program. I will attempt to edit the volume on this upload thanks for your feed back.
Yep, I had to turn up for the voice, and race back to the speakers to turn down for the music.
Can I get a parts list for the wiring component’s
No sorry, I can send you a wiring diagram if that helps?
What do you think this costs to build?
About $4200.00
@welding2go thanks for the reply. It's sweet looking oven you built. I like the four heating elements.
Thank you 👍🏼
What kind of insulation did you use?
Rockwool
Love it !!!
Sweet build !
Thank you! Cheers!
Sweet build!
Thank you!
Great Idea! 👍🏼
Thanks!
I love those latches, where did you get them please?
I’ll send you the link.
Accessbuy Toggle Latch Clamp,U-Bolt Quick Release Toggle Latch,360Lbs Holding Capacity Adjustable Small Latch Hardware for Freezer Door,Storage Boxes,Smoker Lid,Tool Box Case,Trunk,(4.75 Inch) 4 Pack a.co/d/c6mr7FD
This link is for the larger latch. Accessbuy 2000Lbs Capacity Heavy Duty Adjustable Latch U Bolt Self-Lock Toggle Clamp 2 Pack a.co/d/03JoFL5 Hope that helps!
@@welding2go THANK YOU!!!
What size vent did you run on this thing? If any....
No vent is required.
Can i get a copy of your wiring diagram also thanks
Yes, message me on Instagram and I’ll send you a copy
@@welding2go I Will do that thanks
how much power is needed in this tool? thank you
This oven requires 220v / 60amp
@@welding2go how many watts does the overall output of this oven?
@@zoy8295 4 @3000w each
Amazing
And you empty it by......
Take out the step ladder
Hi Did you not need to install a circulating fan for the build.? Or is it working ok without one.
Hi Kevin , Fan is not required, you don’t want any air movement within the oven when setting powder.
@@welding2go thanks for the answer. You see some with fans and some without. Just want to get my build right the best I can
Great work on this project. We shared this video (and the previous ones in this series) on our homemade tools forum this week 😎
Thank you !
Can you send me a link please?
Can you email me the the wiring diagram ? Thanks
Message me on Instagram and I’ll send you the diagram thx
instagram.com/welding2go?igshid=Mzc1MmZhNjY=
Looking forward to see what you will put that motor on.
That build will happen soon!
It sound great!
Thank you.