- Видео 21
- Просмотров 20 756
TSCDEVLOPER
Добавлен 24 авг 2015
Artificial Ventilator With IOT Based Patient Monitor System| Tejas Chavan| DKTE
Artificial Ventilator With IOT Based Patient Monitor System| Tejas Chavan| DKTE
Просмотров: 75
Видео
#TASK 4 #GRIPAUG2021 #IOT AND VISION FACE MASK DETECTION BASED DOOR LOCK
Просмотров 933 года назад
#TASK 4 #GRIPAUG2021 #IOT AND VISION FACE MASK DETECTION BASED DOOR LOCK
Surveillance Car Using Raspberry pi and Controlled Using Redgear Gamepad 🔌
Просмотров 1353 года назад
Surveillance Car Using Raspberry pi and Controlled Using Redgear Gamepad 🔌
What to do when NODE MCU shorted ?|ESP8266 Repair Trick
Просмотров 17 тыс.3 года назад
What to do when NODE MCU shorted ?|ESP8266 Repair Trick
Code and connection plspls
Wish I could hear you over the music! Why?
Bro when i conmected to port it will directed in my laptop but code is not uploading and power led also not turnimg on what's the problem
Hello, I have a board that always outputs a high signal on all D pins. I tried to completely erase the firmware, but even without the firmware loaded, it still outputs a high signal on all pins. The LED on the board is lit. In your opinion, what could be the malfunctions? Could it be that the chip itself is broken?
How to repair the esp8266 if the wire i.e going to be connected in ground get into sk pin by mistake. Now esp8266 is not working , what i can do or should buy a new one....😢
how did you connect your readgear gamepad to raspberry pi? it didnt show up for me..
Contact: tscdevloper@gmail.com if you want more details of this projects
I have esp32-cam and I was gave it to 5.3 v and 3.4 A so its regulator IC 1117 3.3 D135was burned and indication LED also burned, So will it repair .
yes but only if your diode is burned otherwise if microcontroller is shorted you need to replace smd Microcontroller
code?
Hey Bro could you please help me I also have to go such expo on August
Sure
You can see upcoming events on Electronics For You website
@@tscdevloper Thanks for your response but I want to know the procedure
@@tscdevloper the session cost 999rs is it worth it to buy the ticket
@@PrathamProjects Just go to there event site and you have to collect pass from there.
Bhai mere NodeMCU ek bar code upload hoke kam kiya uske badh maine jab plug kiya toh USB not recogonized aara hai cable change kar liya , driver download kar liya , reset karliya ab kya karu
Thank you bhai❤
brother main rc car code upload kiya aur prefect work kiya .lakin abhi me same code apply kre rha ho aur code upload bhi ho jata h lakin android app se control kane pe rc motor work nhi kar rha h.motor driver bhi ok h aur mcu ka light bhi on hai. kya problem ho sakti h?
ek bar node mcu ke pins pe signal aa raha hai kya dekho jidhar driver ko input diya hai like HIGH and LOW
Wow 🔥
Bro can I use 1N4008 instead of 1N4007
Brother ! My Nodemcu is not receiveing any codes and showing the same error again and again.. The led lights are also not blinking... We have done all possible things we could do.. But also it is having same problem.. Does this mean that our Nodemcu is shorted ??
Yes, try to replace diode and check it's working or not
What happens if it gets short again Will this diode protects from short circuit again?
Diode is for reverse voltage protection so if it again shorted you have to replace it again with the new one
Hi can I use 1n4004
Yes bruh it's maximum reverse voltage is 280V so you can use it easily..
@@tscdevloper thanks bro you helped me a lot ❤️ love from gujarat
Please help me 😭 I short circuited the board and before changing the diode I checked it by short circuiting the diode and the led didn't glow but when I short circuit my board now with vin and ground some sparks is coming but the code is not uploading 😭😭
Try it by replacing diode
@@tscdevloper I have replaced it but it is not working 😭
Is the chip present in the board has gone?😭
It helped a lot brother, thank you
You're welcome!
my nodemcu are work fine but its consumption current are about 450 ma . the regulator and Esp12e are getting HOT. what should I do?
when i check the pins with multimeter in buzzer mode the 3V pin are shorted with G pin. i have black component that write on (100 6V) on it and its shorted too.
My nodecmu is heating and blue light ain't showing anything, Mistakenly i've applied 12v to Vin thats why it get shorted and my 3 nodemcu are destroyed with that any idea what to do please help??
Bruh replace voltage regulator diode with new one as like me which I shown in video do it for all 3 nodemcu
@@tscdevloper ohk bro thanks. I will try...
i can't upload any code its not connecting
If you soldered it correctly then it must work correctly ...
Apply Now -> Login -> Redirecting to profile again & again. What to do?
After applying and login you are done with application but may be you are facing glitch in site...
It's work buddy .thank you so much.I was about to throw it away
🎉❤️
THANK YOU BHAIII 🔥🔥🔥🔥
Very good
Kadak bhai
👏👏👏
♥️♥️
Well explained
♥️♥️
Awesome project