Видео

Fast way to change a fuel pump 😭

If I was to approach this from the engine bay, would I need to remove the cowl cover along with the air box? I tried to remove components of the exhaust system, but they are extremely hard to remove. Thanks.

Sorry everyone meant to say 2010 thru 2020 on Toyota Sienna mini vans

What dash lights came on that made you change wheel sensors?

Where Toni get that. Changed my oil the first time yesterday and got oil all over the place. Freaking stupid how they put that filter in there. Thanks for video I wish I would have watched this first and got that part

I have a question. How much should a front wheel speed sensor cost to buy? I have seen both front sides for $30 up to $150 for one side and then Toyota wants $370 for one side, that’s the price for the part in a plastic bag, they charge $165 per hour for labor.

I used my GB40 to start 2.5L Camry. Battery was not completely dead just too weak to start the 🚗.

Yes I screwed up at one point and said fuel filter lol. I was tired and hot and out of breath doing stuff lol. My bad

Great video ! I want to point out that when taking old sensor out sometimes the plastic part that goes into hole gets stuck and part of it comes out . Then you need to remove that plastic out with a screw extractor in order to put new sensor in .

Thanks for saying about the front one being a 5 mm Allen bolt I never would have figured that out right away ,it's so Rusty. I don't know for sure yet which ABS sensor is bad but looking at them the front right one has a crack in the base of the center where the Allen bolt goes through so I would assume that would be a good place to start.

thanks

Believe thats my problem on my 2500 ram. Thanks

ماسكين الدوله النصارى ذولالاتتمشكلون معاهم تفاهمومع اوختكم هند ربوبنتكم ياعيال الزنى يومين

Are both out tie rods going to be the same amount of spins? I forgot to count on the first side

These vans are actually known to have a weak rear end. So towing or not, the fix is those heavier shocks. Monroe 58624 handling immediately noticeably improved.

I was trying to get that end on and could not get it up enough to get it on. Thanks for explaining how to do it.afyer wasting two hours busting my ass your way took me 5 minutes lol

Nice. Thank you this saved me a ton of time. I was trying a 5 ft pry bar trying to lift it up and it was not working. Feel like a idiot after doing what you said lol. Super easy

Straight to the point, nice!

I was tweaking trying to find the right bulb for this. Thank you for not just telling but SHOWING us in this video as well. Much appreciated 👍🏼

My truck is making that noise. At least know I know what that is. Thank you I’ll take it to the shop I’m not mechanically inclined lol

Thank you . Help me get it changed

Thank you . Help me get it changed

Sister got oil change at walmart and it was like that. I didnt think i was ever going to get it off lol

Thank you, saved me alot of time trying to figure that out

Thats looks like a nightmare

How hard is it to take out the radio?

So a gooseneck hitch is out of the question If you do this then?

Thanks for showing where that is and how to to get to it to remove.that was a nightmare getting out. Great job showing.thank you .hope you get to feeling better

Dude, you're awesome! Thanks so much

Nice job. Now I know how to change the bulbs. Thank you

If you do it old school you just touch the bolt head that holds the idler or tensioner on .don’t actually touch the pulley

Fascinating vid, man👍🏻

Thats a sleeper i like it. I had a simliar dump kit on an old k1500 and it handled everything well until i crushed the bedside when i dropped a log on it. Now i have a flatbed 8x8.5 dumper on my F350. Has a 20k pintle hitch built in and it has a regular reciever hitch below it.

Ya that's what's going on with my 06, Thanks guy.😎

Well done. Great job buddy

I could hear the difference after you changed that . Good job I’ll have to try that next time with one of those heat temp guns

Holy cow that brake caliper is destroyed lol 😮. Are you going to film changing the rotors when you do them?

Cool man good deal

I changed out the battery in my Ford F-150 and now the radio and clock do not work, everything else does. I was told to bring it to the dealership so they could run a diagnostic test on it. The radio worked fine before I changed the battery.

love the design and the modifications you put in. nice and light, yet strong. shedding weight it key.

😧😧

In your video on the 2008 sienna transmission you mentioned twice that you did something 5 times. What exactly did you do 5 times? Did you disconnect battery 24hrs, then turn everything off, reconnect and warm up 15 minutes then drive it over 5 days? Or did you do the initial power down once then warm up 15 minutes then slow drive to 55 then stop. Then you repeated the drive up to 55 slowly 5 times after stopping? You have commenting off in that video. Thank you

Not safe just using a Jack!

Actual content that should be on youtube. Tutorials.

Everyone that watches this I’m sorry about the filming and noise. It was hard to do one handed at least till the end. Again sorry for the bad sound and filming at times

Not much fun working in the dark lol. Still it’s a good video

was their usb slots in their?

RUclips never disappoints. Thanks much!

Ha ha. My buddy would have loved to have found this video last week. It took him forever to find that drain plug lol. He said no video for the cx gator oil drain plug location on utube. I’ll tell him there is now 😂😂😂 good video thanks