Видео

Do you have a video of what you did or how to put the jack oil in?

I did this the other day. Left the intake manifolds on the heads. Pushed the rubber intakes up in the airbox. Reverse to put them back. Wasn't much fun pulling the rubber intakes back down but still looked easier than your way.

I need to rebuild the petcock on my 97 Virago. Do you think I could remove it and take the petcock off without removing the entire fuel tank? Is it possible?

You have put a lot of effort into these instructions. I bought one of these old ladies by chance on Sunday because it was very cheap and in good condition. I normally ride a '94 Kawasaki 1500 Vulcan. I had no idea that there were two tanks installed. I have to remove rust from the inside of both. It works very well with citric acid and washing soda dissolved in boiling water. Add 100 grams of citric acid granules and 40 grams of washing soda to 1 liter of water. Fill the tank(s) to the brim and leave to soak. Thank you for your efforts! Have fun with the little lady. Greatings from Germany, Swabia. Always keep the rubberside down! 😎😋

Are these good bikes I was looking at a couple on facebook marketplace might consider getting one for my first street bike

That's the way it's suppose to look. I see no valve marks.

Thanks 👍 can't wait to see rebuild

Did you find the petcock rebuild kit or any other parts that fit for this bike? I'm rebuilding rhe exact same bike and parts are a gamble... Would greatly appreciate any info you got for me!!!

Thank you for this!

That little guy is too small to keep. I’d recommend putting him back in.

Thank you for this video it helped a lot

Vinegar

Use the metal handguer for clothes

Use close line

How about guitar string?

Me and the pops used to use about 30 dental floss strings braided together.

🤣

😂😂

Try US Army communications wire. Steel core wrapped in copper with a super tough plastic coating. To throws sparks when you bump into a chain link fence.

Doesn't make asound

Try using Bicycle wheel spokes. I’ve used them for years

Love the no bs

Honest and straightforward. Ty

Hi, where can I found carburator, I bought Yamaha 200, I think it's YTM, but carb is missing. Let me know if you have one original but used. Thanks

my friend do you have any video about reinstall carbs virago? I have a virago 535 1999.

Don't need to go crazy as he's using a 2 pound hammer. There are several better ways of doing this. I wouldn't let this guy work on my wheelbarrow.

How did the aftermarket carb work? I can't find your video about it. I have done well rebuilding the stock carb but parts are getting hard to find and expensive.

Here’s the amazon link to the carb rebuild kit amzn.to/4d1kyRp

It looks like something a crappy abortion clinic would use, and something mechanics all around the world would need to fish fallen tools in the engine bay out

seafoam in the cylinder with the plugs out... clean it out and NOT hydrolock your engine....seafoam is not combustible.

It would be more clean and efficient to use a blade to cut the bottom off because using that hacksaw creates little fragments of plastic that will get stuck to the “diy funnel” and then mix with whatever liquid you pour into it. Just saying 🤷‍♂️

Impressive ❗

That’s awesome! It amazes me how much shops charge!!!

Text says Japanese dude says China… sheese

Distributor Cap not connected.

I love the last backfire my 351 Windsor after my oil pump locked up at 10 bellow 😂

Did you check your air pressure

Dizzy cap is not connected.

Pull the distributor and see if the pin is broken on the gear

Camshaft is not turning

Distributor cap isnt installed, and atf dipstick way too clean!!! Lol Distributor not turning obviously lol

Worleygig not worling

Apple cored drive gear. I would never guess in real life

The distributor isnt on.

Rotor not spinning

Ain't got no gas in it😂

The sheer pin on the distributor drive gear broke....easy one😂

WHATS WRONG I DONT HAVE IT. 😂😂😂

The distributor shaft is twisted off becuase the oil pump is siezed

Easy fix