Видео

Roll clones

How about you rent a jamb saw for $ 35.00 and do the job correctly

Great video, would like to say that for the legs a ratchet wrench with a 1/4 bit would help tremendously with leveling the legs. I also use my magnetic level on the stainless panel to make sure it's level left to right and also front to back.

Nice job on the video can you do a video of the running up and down? If you can.

Thank you, I should have watched this before paying $200 to have Lowes install

Stud in the way to vent out wall. To much work right

This video was great 👍

I don't know why you have to talk TOO MUCH instead of just doing it while talking. The video clearly shows what you're doing anyway and it paints a thousand words !

Just do the install zzz

HI, I only used the jamb saw to cut the skirting board for 10 mins max. And smoke already come out from the blade, not from the monitor, but from the blade. What does it mean? 1) Does it mean the blade is blunt? I came across 4 nails while cutting.

Have you ever seen one that has 2 blades that turn in opposite directions? I have one believe it or not

Thanks happy holidays

Thx for the ideas. I am doing my 5x8 this weekend. I do mtnc and home services.

Ron Paulk is the guys name

I used my grinder with a diamond blade. Same result. Both ideas here are good.

Gracias

Thanks for this excellent video, but I have a question after thinking about it I also have a 2018 and just lost a bulb. Should I change all the blinker bulbs, knowing that they all have the same number of cycles on them?

Very nice Thank you

Slowest most pointless and annoying fucken video on earth. Imagine the people that have to live with this man!

i mean a lot of helpful things said in the video but the only thing i can say is whenever ive done laminate flooring ive always been told never to have a seam in a door like that it will cause major creaking and boards lifting after a time unless i was told wrong?

You skipped the part on how to “just clip” the sill extension in place and ours is definitely not just snapping in place

Good tip. Thanks.

This is very relevant

I just purchased this saw to cut jambs and a 12 foot brick hearth. I feel much better about tackling the job after watching your video. Thank you for sharing, it was very helpful.

Excellent!!!! Also really sad to see accidental cut on your palm

why didnt you run a finished floor first?

Thank you for your video. Will those bags work with fire place ash?

Thanks! The Ford dealership quoted me $500 for a job that literally took me 5 mins to accomplish.

The most difficult flooring is this laminate crap. The locking system on most of this junk should be redesigned. If I ever redo my floors, it will be all tile

Fuck that dirt road, make the county pave it 😂! Thanks for the video. PEACE!

Hi. Thank you for your video. Which is the best vent pipe cap/cover to prevent critters or rodents from entering? We are having a mice/rat issue in our attic and there are no other suspected entry points.

Thanks for the great explanation

I have a leak there.

I didn’t see the name of this brand. Where was it bought?

What I did was sand some of the lip off which made it possible to snap into position and then using a block tap the piece underneath the door jamb. I don't cut the jamb but instead cut around it. I do cut the arch to fit the laminate underneath. Not sure if it's wise to cut the actual jamb.

Same car here. Exactly the same issue. I am going to try your method.

I’m going to use this method thank you. Although I’m going to use a strong pva glue as well to prevent any cracking of paint on the joint from movement.

I have a 7ft door but the panels are about 14inches and every reinforcement bracket kit is for 18 to 24 inches...any suggestions? can you put the little bracket right into the garage door? I'd rather have it reinforced just to be safe but I'm stuck at this part and don't know what to do - everything else is setup and done except connecting the arm to the door... lol Thanks if you can help - nice video btw!

With a new muffler, apply gray high temp silicone or exhaust sealant, and fill in the seams to keep the salt and water from getting in, and spray paint the entire muffler too, as rust prevent measure.

Thanks for the video. I still can't find the box they covered up.

Man, thanks for this! Fun fact, i have the same truck with the same turn signal lights issue😅

Not related to this video but what type of welder do you have? I’m in the process of buying one. Thank you.

V8 or Eco boost

So you didn't actually glue and nail the boxes? Only the drawers?

Great video I just used a gopro suction cup on the side of the light to help pull the light out :)

Good luck finding the masonry blades. I rented this 3 times from home depot before giving up. Home depot doesn't sell blades that fit. Neither does Amazon. The correct blades are sold online from flooring stores but don't include the adapter to lake them fit. The adapter is hard to find. This saw uses proprietary blades and has zero information on compatibility. If you want this to work you'll need to order blades from one store, the adapter for another, and rent the saw from a 3rd. No thanks.

Too much Bla Bla ! Understood You want to engage views longer but......

Struggled to do the installation, watched this video, done in less than an hour. Good stuff here!

Great

Hey great video thanks for posting it. I had a question can you use wood glue to seam together two pieces of engineered hardwood that's maybe an eighth to a quarter inch thick? To put together two pieces in a doorway?