Видео

No, clamp is only for Amps.

3450/- you will get it in Amazon.

Bohat zyada.

Model number..?

COSLI23011. price 7449. Buy link in description.

I think You have not watched properly, I'm not using membrane in this system. it's not RO water purifier, it's only UV+UF water purifier for soft water.

@@ateebk thank you for replying. Yes I did watch the video, I understand this is not RO. Also if it's a non RO system, we don't need a booster pump I'm guessing? I'm looking to build UV+UF for my room where I get can water and don't have drinking water taps, is there anyway to set this up for no tap?

www.toolsvilla.com/ingco-cordless-impact-wrench-combo-kit

​@@ateebkToolsvilla is very Costly. Every item is min 1000 - 1500 costly.

Thank you.

Motion sensor ke bina nahi hoga.

Sorry bhai maine sirf aapne liye banaya tha..

Sorry, I didn't make circuit diagram.

Yes you can use 3.7v lithium battery with BMS board. You can use 1 or more batteries in parallel if you have space in your screwing machine.

@@ateebk if I used 3 battery should I use the same board 7.4

www.moglix.com/ingco-cdli12415-s12-12v-13ah-lithium-ion-cordless-drill/mp/MSNL5GLO7G6PK4 This is best under 2k, main bhe 1 saal se use kar raha hoon a brand.

I have used BMS board for Lithium batteries. Thanks for caring..

Share me your mail, I will share you some closeup pitchers.

Plastic

Yes?

Sare gears metal ke hain, bohat he aache quality hai, I'm using from more then 1yr.

Set clamp meter in amp, clamp phase wire to check ampere.

Around 3hr for continuous use. For light use it will work full day.

6v 1.5amp

@@ateebk thank you😍

A sirf knowledge video hai, mare paas workshop nahi hai.

@@ateebk bhaiya aap say baat karni h ek baar plz

No complaints, using from 4 months.

Around 250ml.

@@ateebk maine 500 ml dala hai smoke aa raha hai

I don't have repair shop, it's knowledge video.

It's DIY video, aapko aata hai toh khud karna hoga..

Yes, eakdam badia kaam kar raha hai.

Everything is working fine till now, touch is also working good. Using from past 3 months.

Yes, it's very easy to do,

Try with one 3.7v lithium battery.

Around 500rs.

Adress please

Hi, sorry i don't have diagram, check PCB board closely, you will find a soldering location.

Thanks a lot for your reply. I was checking the PCB and i have to say it is not easy to find out which cable goes where....@@ateebk

You can't replace with bigger battery, don't have space for bigger battery.

1499

Take a look at this BLACK+DECKER With KC4815-IN Screwdriver Bit Set on Flipkart dl.flipkart.com/s/Q89i9ONNNN dl.flipkart.com/s/Q8zoyyNNNN

Take a look at this Syska HT200 PRO Trimmer 45 min Runtime 10 Length Settings on Flipkart dl.flipkart.com/s/Q8zoyyNNNN

PIR Sensor 5v to 12v support karta hai aur usmain inbuilt resistor hota hai, you can connect 12v adopter. Connect One motion sensor for one buzzer or horn.

Thank you,.

Sure, main eak chota sa detail video banata hoon.

No, I'm using 8.5v charger.

@@ateebk how much original charger voltage and ampier ?