Видео

I have a brand new 25 Ram Rebel and it does not have the passive entry. I am so angry about this. I’ve been looking for videos and a parts list. Can you tell me how much it cost in parts?

Anti-moan kit 😂 I have a 2019 Ram and it does the same thing anytime there is high moisture. Usually cold or snow or rain or humidity. I remember reading something about the brake assist doing something funny. Basically saying that the moisture can create a kind of caked up layer in the brake, and when the brakes first are used it has to kind of scrape off that crusted layer before the noise goes away. I noticed someone in the comments mentioned they turned off the brake assist, so that reminded me of some other comment I read.

I know someone with that same philosophy, I have to fix all their broken stuff.

Thanks dad

We live in Arizona, so moisture is a small factor in brake fluid. If I lived in a humid area I'd change the fluid every 2-3 years also. Excellent video though!

One of the better videos on this, nice you actually take time to show the wrenching vs just talking about it and cutting to the money shot this old house style!

Which fasteners do you torque with the weight loaded on the suspension and which ones can you tighten before you put the weight on it?

The string is brilliant

Hello. Can I get the tool number for master cylinder adapter?? Thanks

does it run now?

Great video! Thanks so much for sharing it. One thing that might help with the ball joint separation is if you take that nut off and put it on upside down you have a better platform for the lower separator claw to grab. Otherwise if the thing is really stuck in there you chew the edges up and never get it loose.

Use blaster air tool lubricant it’s the best way to go

Thanks for the video and review. Just ordered one using your code. Worked in the UK too. 👍

Too much work rather buy a new one

So what's the Torque specs for tightening the lower bolt of the shocks? Would have been nice if you mention it

It cost me less to have the dealer do it than the cost of the power bleeder lol

I'm debating if this is worth it.

I want to do this but a bit nervous of breaking the panel (especially as I have seen other videos say you really need to yank it to get it off). Any advice for NOT breaking the actual parts and having to epoxy it? (don't care about clips... they are replaceable)

Nice video. I have one just like 👍 t and it works great, but the forward reverse selector is loose and moves out of place.

Will this work in a 2021 limited longhorn

nice

Very nice and Merry Christmas

Great job on the video! Come on everyone let’s help this nice man get to 1000 subscribers! Have a Blessed day!

I was told by my dealer it is not under warranty. 😢

Thanks buddy, I've just bought one of these cheap, it's got low power so I'm hoping a good clean will work wonders like yours did!

I have a husky brand one that came with a 10 gallon compressor. It’s releasing air out by the trigger even tho it’s still working. But I feel like it’s not suppose to release any air from it to make it work. I have to see if I still have the receipt as Home Depot has a 3 year warranty on pneumatic tools according to their website (HD owns husky). If not I’ll be giving this a shot. Thanks for the video.

Please refresh

Machine ka paath Kahan milega

Thanks for the great video! At the end you recommended replacing all the clips instead of trying to reuse them... do you remember how many of each kind are required for each side?

Do you recommend replacing the springs? I don't want to level my truck want to increase the ride height a bit and increase the rough road condition driving - off/gravel, etc. Looking to get similar to the Rebel set up.

I love my quickjack 7000 does so good, if i had deeper pockets I'd buy the metal lift exenders for taller vehicles

My bighorn needs this too, but I’m not big on messing with door panels. Ram really needs to include proximity sensors and led headlights for how much they charge!!

Omg that's such a cheap solution, thanks!

You could put a5100 bilstein adjustable and set it to one or 1and a half inch - you would have a two or two and a half- if your arm was too far angled- you can add a taller tire

My wrench is blowing air and Not working, soñé ideas? It stopped working after water entered it, but it has already been disassembled and cleaned

I’m getting blow by on that exact gun it’s never been used before it’s been oiled any suggestions thank you

it’s not that important to go through all that time hassle and money

How did you tighten the locknut on the top of the strut? I’m doing mine and the post isn’t long enough for me to grab it with a secondary tool.

How long did it take you to DIY the front,rear and UCA? And what’s that tool called to break off the UCA? Was alignment required?

Yeah thank you.Glad I saw it. I'm good with wood.

How did you get the screen out of the fluid reservoir?

Put a small hose on your syringe to get around the obstruction and down into the reservoir. Nice video.

Thank you!!!!! sir

Thank you for this video. My 21 ram 1500 at 19,000 miles has a sort of spongy brake feel, sometimes causing me to press the brake pad twice to feel confident in my stopping power, I believe my rotors and brake pads are fine. I’m wondering if a fluid flush will remedy my situation. Any feedback is appreciated. Cheers

I wish I thought about watching how to rekey locks before calling someone out to do for me , I bought a condo and had a locksmith come out to replace all four locks or rekey all the locks and he said all the locks couldn't be rekeyed so he replaced all four locks 2 deadbolts and 2 knob locks and was charged almost $1200.00 now after watching this video I think he wanted to make more money so I think he told me the old locks couldn't be keyed but I'm not a professional locksmith but I could be wrong

Can you use these with air ride?

Can this be done on a 2019 GMC Sierra 2500?

Does anyone know where to get parts for this?

just cleaned up thee old Mastergrip I got from Costco for like what $30 almost 30 years ago? good heavy stuff haven't used in it 10 years or more the 1/2" impact was frozen a good cleaning and she purrs like a kitten minimal wear compared to many others i have seen here online.. I'll have to get into the 3/8ths that came with it see if its spinning, prolly needs a good cleaning, darn I forgot tool the bearings before I put it together, dangit .. they get a thicker oil at first, maybe slosh 30 weight around in it then drain it? ah I might as well take it back apart do it right

Thank you so much! I lubed mine with power steering stop leak... it really killed the gun but now I see what to do. Thanks