Видео

Kicker GR120 - link in the description. Enlace en la descripción del video

Sorry for taking forever with that, been pretty busy lately. If you have any specific questions about, I should be able to answer

@@ALLVEHICLEOWNERS No problem. I understand getting busy. I will subscribe and wait for your review. Thx for the reply

@@lajabrianspann3234 , by only replacing the purge valve my problem got solved

Say no to illegal street racing, be safe out there

I tried that first, adding a BOV does improve the sound and loudness of the turbo blow off

@ I added a BOV trumpet to the tube and it’s louder than the spacer

@@christianprusinski , that’s a good idea, I think I’m going to try that. Thanks

Oh no! I’m sorry to hear that! I hope you can find the solution, and specially DIY. When my K5 lost connection it was not right after a sw update. It was out of nowhere. I need to look back on my videos to see if I did the sw update either long time before this issue or sometime after. And my update was done around 2022

@@SeviDad this is the update that was just released in fact there hasn't been an update since last October 2023 at least for my seltos. So it hasn't been almost a year but I have done a couple of them before that and never had this kind of issue. I just removed the negative battery cable for 10 minutes to see if that helps reset the modem. Will pin this conversation on my phone to remember to update it. Running out of things to try.

@@douglastaylor999 are you getting all zero numbers on the modem info page?

No, the disconnecting the ground for 10 minutes did not help, exact same problem. It really ticks me off that we pay $200 a year for the best setup and then an update breaks it and I'm sure it will not be considered in warranty.... Unfortunately, this reflects how things are going with Kia these days, with the engine problems and transmission problems etc etc. Really disappointing.

@@douglastaylor999 in my case, I did the software update myself, downloading it from a page that Kia has for that. But I agree that if they did it at the dealer, they should fix it

Thanks for the advice!

Sorry to hear that. Maybe you can try turning the sub a few degrees to either side so that the subwoofer frame holes no longer align with the box holes. Then you can make new holes and insert the same screws or new ones if needed. If that works, it will be best if you seal the old holes with silicone to avoid air escaping

Yes, the subwoofer bumps pretty good!

So these won't work for the comp q class ?

@@christinaabundiz1888 if it fits, I’m not aware. But the information from the Kicker’s website is as follows “These subwoofer grilles fit most KICKER legacy subwoofers, including CompVR, CompVT, Comp, CompS, CompD, and the 2010 CompVX.”

Hi, I didn’t have the right tools for that part of the process, I had to use creativity applying leverage to my small allen with an adjustable wrench. But I recommend more adequate tools in the description of the video. I recommend a rigid one

Here’s the Amazon link to the recommended allen set. amzn.to/3ZJTlxx As an amazon associate, I earn from qualifying purchases, however this won’t result in additional costs to you.

@@johndeer-dv4wy that’s right, no tune is needed

The App name for iPhone is Expert. There seems to be three options of this app with a slightly different name, they all look the same

With this BOV installation, I can get some loud sounds mostly with the gas pedal release timing, doing this when the turbo has charged the most boost and before it actually uses it. Mine also has the K&N intake filter in place of the filter box.

@ALLVEHICLEOWNERS I have the aem setup with the boomba Racing Blow Off Valve Adaptor does the bms hit harder?

The install I show is only for the EX, GTLine and lower trims with the 1.6T engine. It doesn’t apply for the 2.5T GT

Thanks for your comment! I look forward to do that mod, waiting for the right moment to change the whole intake system including the turbo inlet silencer.

Thank you for your comment, I would love to hear how it sounds on the Tucson. As for the K5, I’m pretty happy with this mod, it makes it more fun to drive! I also have some ideas to make it sound louder, just need to have some free time to give it a try.

There are sound adjustment screws in it, have you played around with those to get the desired sound?

​@phillipbrazil2108 where would the screws be on this little adapter tho I don't see any. It's more of a baby psst sound if anything

@@WIDERisBETTER from what I see there are 3 along the side of it. BMS has the same on their’s but I believe their’s are just 3 holes without screws

I didn’t disconnect it, but I have seen comments of people that have disconnected it during installation. The important part is to make sure you take picture of the correct orientation before so you have a reference when you install back. Also ensure that the wiring connector is put back in correctly.

Hi, I love this digital EQ DSP, it's a great tool and it helps to repair frequencies that my car factory stereo is filtering out (killing). The sound from my speakers is much better with this device. You should get it. Here's the Amazon Link amzn.to/3PJ9K1s

@@ALLVEHICLEOWNERS ok cool. Thanks

​@ALLVEHICLEOWNERS hey so what channel are your rears speakers on?

Lo envié en el otro video

Hi, this link should take you to the BOV for K5: www.addw1.com/products/add-w1-blow-off-valve-adapter-for-kia-k5-hyundai-sonata-1-6l-turbo?_pos=1&_sid=30d3359af&_ss=r

I’m sorry to hear that! If the bolt got stripped, there are ways to take it out, but you should have replacement bolts in hand because that one might no longer work. Those bolts are very tight, is important to have the right size allen wrench and preferably the T type like the ones I included the link for in the description.

@harrisq2046 take out the rubber hood stopper above the screw/on top of plastic and u can stick a long Allen key down into it and grab top with some channel locks & turn just enough to get it loose then twist rest of the way with your fingers. Had this issue myself til I remembered to remove stopper. Hope this helps!

Thank you for your feedback, I will update the title. Sorry for the inconvenience.

@@ALLVEHICLEOWNERS good man!

Hi, thank you for your comment! The Avid Ascend have worked really well for me.

No lost of power with the install.

My man that HOT air intake definitely lost you some power

Not really, the car still feels powerful enough. I kept the air intake guide that brings air from the front to where the intake filter seats. I don't feel like there's any heat soak during winter and cooler months, might be a different story during summer.

😂 haha, stutututu might need some other mods

@@ALLVEHICLEOWNERS Forgive my uneducated brain I'm sorry

It’s all good! I don’t mind the comments!

Most likely it is