Видео

What if the inductor is working but the charger is not?

Bhai aapse contact kaise karun mujhe bhi realme 3 pro ki battery 4000 se 7000mah karni hai samsung f62 ki battery lagwani hai

I need 2pieces .how I get it in north east india?

Old sub spekar really awesome

I got shit splatter on the walls.

Input 12 volt 7 ampear and out put 16 volt 5 ampear hoga

Can i use 12vl

I got 15.5 until i swap the filter caps. I want 18 volts

Hi my laptop charger output shows only 1.5 volt ... When i removed optocoupler showing unstable 19-21 volts . Then i installed a new optocoupler again the same problem showing 1.5 voltage. What is the reasons

Bms????

Do you see a difference in usage? Or will the phone drain battery as usual as set by manufacturer?

It's very good experiment but not user-friendly also. Because no water resistant 😞. Dust and moisture enter and rip soon 😌. But overall good experiment brother

Step up perigoso, entra não que é fria. Se a tensão na entrada cair a 3,5 volts, a saída chega a 40 volts, ou seja, erro feio de projeto, problema exclusivo desse chip xl6009.

Is this a constant current or current limit supply, those are two different things

is it better than pam8610?

Thanks for helping through your information ❤ keep it up bro 💯

Excellent information and presentation! I clearly understood your tutorial. I have a few 19V 3.34A Laptop chargers lying around. Now I can use it for actually charging a sealed Lead-Acid batteries that I use for my experiments and a mini drill. Did not know I have to short the output of the Buck Converter to get an Amp reading! Very nice of you to answer all questions asked! Thank you so much and keep it going, Sir! Maha from Seremban, Malaysia!

Resp Sir! Very నైస్ క్లాస్ Sir. -- ChinnaRao Paderu Andhrapradesh

Its 14.9V initial charge until it reaches 14.9V trigger voltage that is when the second voltage kicks in of 13.80V. So, the charger would need two different charge voltages. Charge and float.

LOL You have a good sense of humor. Good video.

Its too loud bro!

Sir can i replace 450v 100uf capacitor with 500v 47uf capacitor in 135w 19.5v 6.92a laptop charger

Mine charger pwm ic got burnet how to replace it 33 watt vivi charger

When I check my laptop adapter output is good but when I connect with my laptop that time charger is not accept lode

By link

Amplifier se connect krte hi humming araha ha, baki sab thik ha, problem kaha ha batao, laptop ka adapter ha...!😊

Please what do yyou mean by not connection capacitor backwards

DOES IT HAVE AUTOMATIC CUT ON AND OFF FOR CHARGIN?

Esa karne se Bhai kuchh video me bol rahe the ki 1-2 month bad battery battery ful jayega kya esa ho sakta hai esi phone ka experience bata do 😢😢

Sir Mera samsung np350v5c Laptop ka Power adapter hain..... GH - 19v - B Wo abhi Laptop chala to leta hain par ... Cirkit main ek parts blast hua hain. Cirkit main Interference supration Capacitor k bad jo (Mov) parts hain ....Wo Blast ho geya ...( Abhi Konsa value ka Mov Replace karu ) Please Help Me 🙏

My adapter has an IC with six legs,not the same(its so tiny that specifications dont even exist),what do I do in this case,how shall I detect the resistor to pull out??..Nice video and work by the way..thank you in advance

Laptop charger ko plough me dalte hi house ki mcb trip ho rahi hai or house ki light off ho rahi hai kya fault hai ?

❤

does this module have short circuit protection and reverse circuit protection?

My buck converter is always in current mode( red led is on). Why?? It has red and green leds, but only red led is on. Can you help in solving my issue.

Brother, the charger of my Asus Tough gaming laptop is not generating voltage at the output

Bahi ham pakistan ma rahtay hain aur hamaray payri zuban urdu hay agar urdu ma bataday day to kuch ham bhi sekh latay

Current draw is limited by the sink or target, that implies even if we give 100Amp to a LED that can take only 10amp, the led will take only that 10Amps! (Voltage is a different story though) Current is decided by target/sink and once the sink's maximum current is reached, it would stop taking any higher current like the Ammeter in this test shown In a way we cannot overdrive current beyond what the sink can take, sink pulls current it can take, we cannot 'push' current into sink (if I may say in terms of mechanical motion)

170w lenova adopter voltae 19.5 or 20 shows immediately drop 1.

Good زبردست

Ampier loss 😢 so only voltage

Please make trigger for 20v output

sir I have a 19-volt 3amp laptop adopter my problem is when I give load on adopter voltage, it automatically gets 0 volts

Contact number

Should I place a diode so as to no reverse current flow from battery when power is off ?

Bhai kya mera phone bhi Aisa kar doge

Sir I have a 24 volt 3 amo power supply and want to charge a 12v 7ah battery, as you suggest to set the limit voltage and current but after full charge is it necessary to remove battery from charging connector, I mean will it be automatically cut off charging after fully charged because i want to engage it to my mini home ups to charge the battery?

Why did you choose resisters in series and left other

i am getting 18v output which should be 19v acer laptop charger.indicator light on charger is ok..but laptop is not taking power..after long rest again charger works.. there is small burnt in circuirt board below main capacitor but not in any green part of PCB and any other components. any solution?

Bhai Hindi Me Banao Na English Mai Video Banake Kisko Sikhaoge Foreigner ko ..