Видео

brilliant helpful video cheers

I'm doing this exact sensor now... managed to get the covers off and wondered how to move that lower cover, so you managed to get a spanner from the top? That's a tight fit! I got the sensor socket but think its was a cheep one and the jaw opened a little and slipped.

Does the mokka have any pressure sensor glow plugs ?

Nice one thanks 👍🏼

Hello mate we’re can I get the manifold from thank you

You wouldn't happen to remember the size of the ball joint pinch bolts would you?

Hi did you get wheel rubbing on inner wheel arch?

Great video could you do a video on the kia venga 1.4 car blubs please

After watching video mate had exactly same problem. Garage had told me all sensors and ecu . So I decided to do battery £190 . Now all good and back to normal dealers tell you anything.

Thank-you. Why they dont put this in the manual is beyond me!

What was your final jetting with that bike 120main n 35 pilot?

Great video, how often do i change and where is the fuel filter?

sorry if this seems like a dumb question but do you have to flush oil and coolant before getting the oil coolant housing off?

Teşekkürler, Thank you 🇹🇷

Try to improve your camera photography so that the video is clear.

Good job. Think you mean forum not form room though?

What’s the sliver thing on the left side of the air filter I’m building up a xv353 and I can’t seem to figure out the name for that

Its possible to remove oil filter without drain oil;;

A mini only has bank 1, bank 2 will only be v engines. B1 S1 pre cat (S1 = sensor 1) B1 S1 post cat (S2 = sensor 1)

how sturdy is the roof for working on eg cutting holes for skylights with you sat on it

you should connect your battery to the solar controller before connecting solar panel to the controller as that way once the power from the panel is going into the controller it has somewhere to dump the electric coming from the panel

Brilliant video 👏

thanks for posting this, even if it was two years ago. Very helpful.

Hi thanks for this video, big help, have all the stuff I need but just want to check, I can’t get the brown and brown and white wires out of the old relay block, do I cut them? Thanks for any help

10mm you say?

Hi mate, is this the fuel tank? I need to drain out the diesel in my petrol Mokka. Long story lol

No copper slip? 🤔

My charging socket and cigarette (usb) socket disconnect sometimes and goes back on what could be the problem?

Thanks for this. I’ve been ploughing through it today. Got all the manifold nuts then decided to finish for the day and shut the bonnet with the cable disconnected. 😢

Would you happen to know if the oil filter housing gasket is located in the same place on mini one r56 1.4 N12B14A? I will be changing my catalytic converter, and this is the only video that's been helpful so far. Thought my as well change these if they're exposed in the process

I'm having problems my front wheel bearings keeps on going bad it doesn't last 1 month I don't know what causing them to fail please advice

If you've got an egr error code, you'll probably need to pull off the egr pipe work and inlet manifold and clean all the carbon build up out using oven cleaner. Replacing/cleaning the egr valve might solve your problem but a gunked up egr valve usually means blocked/gunked up egr pipework and inlet manifold.

whats the size of socket you use @1:26

Model 2006 Renault Megane

The lever is not ment to be at the line but 13,5-14,5 mm below the Lines acc. to manual

Hi tryed this but no luck so far put swivel on passenger seat but its a double do i need stronger resistor maybe ?

Just watched how you stripped down the Renault Master for Radiator Replacement. Thanks for sharing your knowledge Jay, I now feel confident I can do the same job on my campervan which has just sprung a leak! Nice work, looking forward to watching more of your videos! 😎👍🛠

This is a safety recall by peugeot and will be done free of charge by any peugeot dealer

Bad - Very BAD --- you did not show how to take the housing off & put them back on. Plus, you shown the old brake pads at 1 view toooooo long.

what's the tool called for putting the thread in

😀😀"bush-whakin alki piece of ..."

Hi mate i changed ours and it seems to be leaking around but that screws into the housing? Ive done it up to 25nm as specs say new seal etc any help? Thanks

Hi mate, where did you order these from? I don’t like the ones that round off at the end, I like these

Any link for that solenoid? I can find the egr valve but not that sensor/solenoid

Very explicit video with so many useful details. Keep it up 👍

Twas hard to listen to him because he has bad asthma or summit . So the puffing and panting made it unclear at times.

Happy days mate looks well. Drop me a message if anyone requires 1 👍

WASTE OF TIME THAT VID WAS!

Anyone got the part number for the S1? I ask as S1 and S2 are clearly not the same connector at the electrical end.

Hoping you can help. Have some vG20A carbs which are seized solid so replaced them with vg26vb carbs but can't figure out where the fuel lines run. Have the 2 off the 1&2 and 3&4 'fronts' which run into a T piece (can be seen at 15 mins in video) but there is a separate big fat fuel pipe running to the back of the carbs. Does this connect to the same fuel line from the fuel pump? Any help would be really appreciated. Thanks