- Видео 6
- Просмотров 34 793
Bob6642
Добавлен 19 мар 2009
MultiRotors and other Autonomous and Semi-Autonomous UAVs.
Designer/Builder of BobsQuads IMUs, FCs, MCUs, Frames and anything with a BobsQuads name on it.
Designer/Builder of BobsQuads IMUs, FCs, MCUs, Frames and anything with a BobsQuads name on it.
Mini32/ProMini32 + 10DOF (MPU3050, ADXL345, HMC5883L, BMP180) r164 Software
Mini32/ProMini32 (STM F103 based MCU) on a 8bit MultiWii Pro Mini Shield. Sensor = MPU3050, ADXL345, HMC5883L & a BMP180 Barometer.
Просмотров: 1 649
Видео
MultiWii 1.9 Heading Hold Test on a BlueSkyRC MicroQuad and a Bob's 9DOF
Просмотров 1,3 тыс.12 лет назад
Testing Heading Hold in MultiWii 1.9 using a Bob's Super Simple Shield, Bob's 9DOF, BlueSkyRC Micro Quad outfitted w/ HobbyKing 18-11 2000KV motors, GWS 5x3x3 CW/CCW Props, Turnigy 10A Plush ESCs, running 3S fed by a Turnigy Nano-Tech 850mA Lipo and input from a FrSky TFR4 2.4GHz FASST PPM SUM Out Receiver. Transmitter is a Futaba 7C FASST unit. Shot using an iPad.
FreeFlight IMU 6DOF Cycle Time in MWC GUI 1.7
Просмотров 1,3 тыс.13 лет назад
FreeFlight IMU 6DOF Cycle Time in MWC GUI using ITG-3200 & BMA180 @ 400KHz
Programming KK / KapteinKUK V5 SMD Multirotor Board
Просмотров 16 тыс.14 лет назад
Programming KK / KapteinKUK V5 SMD Multirotor Quadcopter Tricopter Hexacopter Y6 Board www.rcgroups.com/forums/showthread.php?t=1143569 www.kkmulticopter.com/
KapteinKuk KK Multicopter V5 SMD / SMT MultiRotor Controller Hotplate / Skillet ReFlow
Просмотров 14 тыс.14 лет назад
KapteinKuk V5 SMT / SMD MultiRotor Controller - Hotplate ReFlow - Solder Stencil used
Only 2 hands
Sorry, just saw this response....:/
You failed camera hold test.
Is the source available on a version control site like GitHub? Thanks...
@bob6642 Where can i buy one. Im looking to just put it on my quad and thats it, not really build a board.
@honda125 a BobsQuads Shield w/ ProMini and a Bob's 9DOF. I can't add links but if you google 'Bobs Super Simple Shield' you will find it. I am the 'Bob' that makes them.
what board are you using?
@TheTurbinator totally depending on what you want, the best or the very cheapest just as long as it flies? The cheapest would be one with only 3 gyros and no controller card which works supriseingly fine but you still need TX, RX, motors, batteries and so on but if you get the cheapest but still ok stuff i guess you could make one for maybe a few 100 bucks.
I have been trying to find an answer everywhere, how much does it cost to go from having 0 parts, to having a completely working KK Multicopter in your hands?
i use a skillet to slow down the temp as the hotplate surface gets very hot very quick. using the skillet gives more control on your end (do not eat from the skillet - it must be used for solder only)
@iulian207 thanks :)
super,nice job