Видео

It’s so fluid!! I love that, I can’t wait to see it in action irl

PLEASE can you tell me (communicate with me) how to get this damn software to communicate with Arduino?........ YEAH!... WELL, this whole thing isn't easy for non-programmers or beginners when it comes to setting up the software. I've spent THREE WEEKS tearing my gray hair out trying to get the Arduino and Bottango servo board to communicate--without huge ERROR NOTICES! I've asked folks on these Bottango RUclips videos to help me so that I may offer positive reviews. No one has responded! I suppose no one cares! Well, I am not posting positive feedback since the Maker never responded to my email contacts, RUclips videos, Reddit, or Facebook. Neither has anyone else! So, until individuals start assisting others, I recommend that everyone utilize Maestro or another program. The Bottango community and Maker have no decent RUclips videos to walk folks through this. They only have videos that celebrate the awful item and their animatronic parrot and bear. It's all hype. They shortchange the consumer by directing everyone to the "Manual." This is wonderful and dandy IF you can read it! It appears that persons who are overly intelligent FAIL to simplify their manuals and instructions. They also do not utilize uneducated individuals to assist them in troubleshooting these kind of problems, which they DO NOT SEE. Well, Bottango fans, what little there are, I'm really furious about this program. I studied the handbook, installed the joints and motors, and worked out the Port issue. To get Arduino to establish a pORT, it appears that you must turn off the "LIVE" setting in the program. THEN, you activate the "LIVE" button. The Buttango Servo Board is a major difficulty. I'm pretty upset about this. The board states that the voltage input ranges from 5 to 8.4 volts. So, after hooking it into an adaptor and letting some of the live servos run for a brief time, it BURNED OUT over 15 servo motors. I am F--- GLADE I do not hook this into my REAL animatronic device because I would have to GUT the F___ thing and replace all the servos! Thank goodness I used test servos that weren't hooked to any mechanism. I've also seen that several RUclipsrs just utilize Arduino Uno or greater boards, with breadboards connecting everything to Bottango. I am wondering why. So, if someone calls me for assistance, I will remove this nasty message, apologize, and provide positive feedback. OTHERWISE, it remains available on RUclips. BOTTANGO must take responsibility and recommence their teaching movies, as well as respond to these comments. SLIENCE BETRAYS THEM! ANYONE that wants to help can contact me here... I will be more than grateful; I will even pay you $$$$$$ SO, lets SEE IF anyone communicates??? :o) ROSS: 360-421-7195 ROSSMARSHALL@weirdvideos.com.

YEAH!... WELL, this whole thing isn't easy for non-programmers or beginners when it comes to setting up the software. I've spent THREE WEEKS tearing my gray hair out trying to get the Arduino and Bottango servo board to communicate--without huge ERROR NOTICES! I've asked folks on these Bottango RUclips videos to help me so that I may offer positive reviews. No one has responded! I suppose no one cares! Well, I am not posting positive feedback since the Maker never responded to my email contacts, RUclips videos, Reddit, or Facebook. Neither has anyone else! So, until individuals start assisting others, I recommend that everyone utilize Maestro or another program. The Bottango community and Maker have no decent RUclips videos to walk folks through this. They only have videos that celebrate the awful item and their animatronic parrot and bear. It's all hype. They shortchange the consumer by directing everyone to the "Manual." This is wonderful and dandy IF you can read it! It appears that persons who are overly intelligent FAIL to simplify their manuals and instructions. They also do not utilize uneducated individuals to assist them in troubleshooting these kind of problems, which they DO NOT SEE. Well, Bottango fans, what little there are, I'm really furious about this program. I studied the handbook, installed the joints and motors, and worked out the Port issue. To get Arduino to establish a pORT, it appears that you must turn off the "LIVE" setting in the program. THEN, you activate the "LIVE" button. The Buttango Servo Board is a major difficulty. I'm pretty upset about this. The board states that the voltage input ranges from 5 to 8.4 volts. So, after hooking it into an adaptor and letting some of the live servos run for a brief time, it BURNED OUT over 15 servo motors. I am F--- GLADE I do not hook this into my REAL animatronic device because I would have to GUT the F___ thing and replace all the servos! Thank goodness I used test servos that weren't hooked to any mechanism. I've also seen that several RUclipsrs just utilize Arduino Uno or greater boards, with breadboards connecting everything to Bottango. I am wondering why. So, if someone calls me for assistance, I will remove this nasty message, apologize, and provide positive feedback. OTHERWISE, it remains available on RUclips. BOTTANGO must take responsibility and recommence their teaching movies, as well as respond to these comments. SLIENCE BETRAYS THEM! ANYONE that wants to help can contact me here... I will be more than grateful; I will even pay you $$$$$$ SO, lets SEE IF anyone communicates??? :o) ROSS: 360-421-7195 ROSSMARSHALL@weirdvideos.com.

This is really cool

How do you animate him in bottango? Pls make tutorial i need this bc idk how to connect him to bottango

It looks like it’s constantly surprised 💀💀💀

thanks for the nightmares

this is honestly very impressive

m.ruclips.net/video/3JCJjTglWOg/видео.html

Recommended 2

I thought the title said Mark Whalberg.

i think wall-e had too much of the white stuff. where did he even get the stuff? XD

Amazing work!

Cooool 👍👍🦔🦔

Ого! Класс!

👏👏👏👏👏

I love wall.e

That’s super impressive! What?!

I love walle

Recommended

❤❤❤❤

I never understood why Wall-E seemed to miss that he had a built in weapon, every time he was in a dangerous situation.

sieht mega cool aus :)

How is your Wall-E holding up in 2022?

Why is there smoke coming out from wall-e?

This so cool

Ay yo, why the fuck is it smoking my guy.

Steven can you tell me how you made the led strobe effect?

Needs some fine tuning. lots of play/rattle going on here.

can you tell me what setting you are using on it,mine prints like yours but slow need to speed it up more .

are you using marlin on this ?

I just purchased this printer. Just wondering, could you tell me what software you are using, and what firmware as well please?

geil!!!