- Видео 6
- Просмотров 9 849
Kzander Ardenflaas
Добавлен 28 апр 2013
Starlink Mini Alternate Power Supply Part 2
Starlink MiniAlternate Power Supply Part 2
Low Voltage Board:
www.amazon.com/gp/aw/d/B0CMWCYPBC?psc=1&ref=ppx_pop_mob_b_asin_title
Enclosure:
www.amazon.com/gp/aw/d/B07VF1VHCG?psc=1&ref=ppx_pop_mob_b_asin_image
Low Voltage Board:
www.amazon.com/gp/aw/d/B0CMWCYPBC?psc=1&ref=ppx_pop_mob_b_asin_title
Enclosure:
www.amazon.com/gp/aw/d/B07VF1VHCG?psc=1&ref=ppx_pop_mob_b_asin_image
Просмотров: 770
Видео
Starlink Mini alternate power setup
Просмотров 5 тыс.2 месяца назад
This is how I power my Starlink Mini using a Dewalt tool battery Cable: www.amazon.com/gp/aw/d/B0CN4HFY5B?psc=1&ref=ppx_pop_mob_b_asin_title Battery Adapter: www.amazon.com/gp/aw/d/B0B4FS1NV1?psc=1&ref=ppx_pop_mob_b_asin_title
Howell Fuel Injection on my YJ
Просмотров 2,1 тыс.4 года назад
Just a little info on my YJ fuel injection install
Jeep YJ off road light switch install
Просмотров 4424 года назад
This video shows how I installed some accessory switches in the dash of my YJ with very little modification.
Jeep YJ seat upgrade (BMW 3 series)
Просмотров 1 тыс.5 лет назад
Just a short video about my seat retrofit.
Jeep Wrangler YJ battery upgrade
Просмотров 4215 лет назад
Showing how I modified the factory battery tray on an 89 YJ to accept a full size (oversized in this case) battery.
Nice setup ryobi & rigid have low voltage cutoff in the battery so perfect for these projects
How long can you run the mini using a Dewalt battery?
@CanyonDavis I had a 4AH fully charges go about 3 hours streaming.
Part 2, with voltage cutoff. ruclips.net/video/1VEIlBrqRJ0/видео.htmlsi=cHFUF8kSN71zzrFl
Use Anderson Powerpoles, as connections
Not quite sure why these would be needed.
I wonder if you could use o-rings on that barrel connecter that goes into the starlink mini to help seal it off?
I imagine you could. Or use silicone to make a seal.
20v 4ah battery lasts about 3.5 hours.
I read that the Starlink Mini cable uses 5.5MM x 2.1MM connector, not the 5.5MM x 2.5MM that you purchased. Your center pin socket being 2.5MM may barely be making contact.
Seems like I saw something about that also. That being said, it works well and I've had no issues after about 25 hours of use.
In the Manual it says 5.5mm x 2.5mm 🤔
@@Technikfreak11 Then why does a 5.5mm x 2.1mm fit? In what universe does a 2.5mm pin fit a 2.1mm socket?
@sportcoupe2 the pin contacts in the female side are spring tabs, so I suppose it's possible.
@@kzanderardenflaas2238 No, I have 2.1mm and 2.5mm connectors, they are not interchangeable.
Just be careful. Dewalt batteries do not have low voltage cutout in the battery.
Very prophetic. :-I
Did you ever do any more upgrades to the yj
I'm in the middle of I stalling dana 44s and a 300 T/C.
Damn! Love this!!
What switch is that!?!?! I have an 89 and have been looking for a switch pod that would fit in that “dead spot”!, but your switches are even better!!
They are standard panel mount switches you can get from Amazon or any electrical supplier
I just picked up leather seats from an RX8 and modified the seat rails and the original brackets on passenger side. Wish I would have seen this beforehand! Did a lot of the same things you did but I don’t have the fabrication skills you have. You did a great job, sir. Wish you had more clips on the work you’ve done. I have a 91, and there are not many DIY custom videos like you have done here. Thank you for posting it.
What happens to all the evap lines as far as the charcoal canister?
It's all there
What year is the seats
I'm not sure at all. The guy I bought them from said 3 series BMW.
What wire did you use or what did you jump off of to get ignition and starting voltage to power the ecu (3 fuse) fuse block
Thanks for watching. I ran from the original key-on ignition power circuit.
Thanks for posting. I have the Howell Fuel Injection kit and a new rebuilt 258 to go into 1985 Jeep J10. I wrote down the information on the A-Team HEI distributor also because I have seen on other installs of the Howell install where they recommend getting the HEI for spark.
I tried to run that rascal but had poor drivability. I put the og ign back in.
Seats look good man. I have cavalier seats in my yj at the moment i hate the way they look.. But I found nice leather seats form a jaguar I'm going to pull from the salvage yard they look a lot like yours cant wait to install them