Видео

Please make them Z-Wave compatible!!!!!!

Finicky, hard to set up, unreliable, narrower than standard so will almost always show damaged paint from old vent. Unfortunate, because when it works it really solves an issue many of us have. Recommend you wait for 2.0 if they make it.

I wish you would do HomeKit

good stuff, thank you for the education. I am going this route! Will be contacting for recommended setup

Sounds like a good product, and should you just want/need a couple of vents it’s doable for most. But a whole house, not so much. You’ll end up spending thousands and should the company not survive……. Ouch!

Pucks seem to be too expensive for working only as a temperature sensor.

using the room controller, if you needed to power cycle a wifi wiz smart light, how would you do it?

Promo SM ✋

Share price please

*This was perfect for my greenhouse! **Fastly.Cool** and Warming environment perfectly controlled I love how it keeps track of the temperature so you are able to go back and check how it fluctuates through the night/day*

Putting together a video distro project for a church. I was wondering, will the Unifi Building to Building Bridge and unifi switches carry the packets through? The church has two structures and they want to avoid running trench lines. Great Video. Thanks!

Are you calling the access control card reader the PDK button or the PDK panel?

Damn,this is old

Do it can be used with switch connect through fiber convert then to convert filber and switch and to HDMI tivi is ok?

*_Love it!>>>_**_t.co/lo9oxS9u5V_**_ However, I gave it to my bf, since it was not compatible with carrier brand heater/AC unit. Carrier made their units not compatible with the Ecobee or anything else like this. Carrier made it where you have to purchase there’s. If you have a Carrier unit. Save yourself the disappointment not being able to use the Ecobee._*

so what is the video latency from source to destination?

How much was the driver license? THanks

make a video about video and be out of focus 90% of the time .. great job

Derp, Derp, Derp....... Fuuuuuuuuu

Intrested

lol this eating so much bandwitch but it is cool!

hahahahhahhaha

Is he a woofer specialist?

This the new g! love this .. im a directv tech, I always ask myself if this existed,or if I could make, because customers always ask me for mirrors,and I always say you can not because you will not aver in hd. but now I have a solution, it's time for some extra ca$h!

you didn't show off the video quality.

Have you looked at Octava kit?

The design is shocking shame really, could be a great app.

is this product no longer avaliable? And will it do 3D?

this is quite interesting, but i have a question, say i want to install this system in my new home, how much do you think this'll cost me? i checked the website, and they don't have any prices posted on it Thanks for the video man

We're getting too lazy, lol. I am for technology, but this is just too much for me. I think this would be great for senior citizens.

the lip smacking was horrible .. turned me off

@carl313313 Oh if you wanted to know (ignore if not XD): HUB's forward all frames out of every port simultaneously and do not keep a record of where a device is located. Switch's use ARP to record what device address is located on which port, and then directs individual frames with that destination address only out of a particular port.

@carl313313 A switch will send a frame out of all ports in the same way a HUB will if a broadcast frame is transmitted. The reason I asked is because many of these "Home LAN" applications just use a broadcast to communicate, and it does saturate the network (Can be avoided with VLAN's if you have the correct equipment.) Thanks for the 1Gb/s LAN tip :). I run 10Gb/s around most of my home so I should be set to go once I get a bit of cash together (Study costs eating all my money :( )

Is this a broadcast technology or is it full layer 3 TCP/IP? Also what network speed is required for full 1080p?

What sort of cost do these units come with?

ollylewin. That is incorrect. If you only had a few tvs and wanted instant switching on every tv all the time you would need 1 extra receiver per SOURCE. How ever in a larger project that has a bunch of tvs active you will still see the instant switching that there is now. If you are seeing 10-30 seconds switch time on a system you have other issues that need to be resolved.

Without being the one who soured the cream this video is misleading. I install these and Im on v1.2 at present and see switch times of anything between 10 and 30 seconds!! The only way to achieve what you see here is to have two rx units per display and switch between them. Not quite what we all wanted but close.

how much would it cost to prepare your house for this?

I have a few questions how does it work? Do I need some extra hardware? to control all my house or just install and go i new to ipad and Im planning on getting this app please reply. Thanks.

@cantfindausernamedam 1. Yes all control4 systems are 2ay. 2. Yes. In the next upcoming video you will see it interact with PTZ cameras and fixed cameras. 3. Yes many new videos will be up in the next week Kevin

couple questions. 1. does this system have 2 way communications? ie, tell the thermostat to go to 22 and it tells you when its at 22? 2. does Control4 do security camera view and control as well? 3. Will there be other videos created showing other features aside from the music and hometheatre control? thanx

Hey jason. The wakeup function will be added to the iPad app in about 20-30 days. The wakeup agent is control4s version of an alarm clock.

kevin- is there a driver written for this? where can i get it?

the Receiver has an IR receiver in it and an emitter port in the transmitter so if you pointed the remote at the receiver it would emit the signal at the source.