Видео

I get what he's attempting to do but he's making it so much harder then it needs too be a block to pull up onto a couple tire irons wd 40 or starting fluid a lighter and an air hose and hes good to go

Bigger BFH!!!!

Lol you may need some time out of a truck lol

I hope nobody was injured or killed. That was horrendous.

That man is a TRUCKER! I’m just a truck driver,

Wonder if it needs injectors? Fresh fuel and drive it like you said should help.😊

Except for the part about doin it wearing flip flops. Jeeeez

lol

Is that whitewater?

Good job on straightening/cleaning the pulley but those tabs are there for a reason, its to keep the belt on.

Thaks for the video, i've never tought that you could (should) bleed brakes from bottom to top, but now i know better.

Best video yet!! My kind of mechanic. 28 oz. Estwing

Best video I have seen with all the steps and explanation. I was wandering what the tool with the hammer is for. Now I know. thanks for the effort.

smh!

I’m sure you are already replacing those spindles again. Pumping grease into the zerks does absolutely nothing to lube the bearings in most cases. The bearings used by most manufacturers are bearings that are sealed on both sides. This prevents the grease from ever getting to the bearing. In order to get grease to the bearing you need to take out the bearings from each end of the spindle and remove the inner seal on the bearings. Also drill a weep hole in the body of the spindle and tap it for a screw to be used as a plug. Remove the screw when pumping grease into the assembly. This will allow air to escape. Once grease starts coming out of the weep hole, put the screw back in. This is not by any means my idea but something I learned right here on RUclips.

Love your videos, Pilgrim! Appreciate all of your hard work!

Awesome 😂

Nice video, you got most steps correct, next time leave the pto alone and just undo the engine mounting bolts. You can slide the engine all over the place and it makes life really simple. Have a great day and enjoy future endeavors.

Thank you so much for sharing very helpful 👍👍

Ese cilindro que pusiste es de la marca Oberol ??

That PTO is extremely heavy and expensive.Never hang the PTO by its wires. You risk damaging the wire connection at the PTO. Just un plug at the connector.

Thank you! You’ve saved me!

where did you get the vertical exhaust for a 3032e?

I’m having an issue where the bolt is spinning with the housing and loosening the latter instead of spinning freely. Any suggestions?

Hope it was worth it

Classic😂

damn!lol😅

Excellent from NW WI

What spray were you using to clean up the grime in it? Brake cleaner?

Only thing this kit needs is a tool to insert the plug, trying to twist it in on a California trimmer mower with the head still assembled is impossible. I installed it with the spark plug but im not able to remove the spark plug without pulling the insert out with it.

I'm in Wisconsin to

Hello i have one of this same model.. but its leaking gas from the cap... I check the gasket and is good... any advice?

Great instructions, worked great on my corvair aside from one issue. Unfortunately I rushed through the process, and with my limited visibility, didn’t realize I had tapped threads into my piston until it was too late. You win some you lose some I guess. Aside from my stupidity, your instructions worked flawlessly though. Concise and to the point.

I have been searching for information on why my motorcycle's oil burned after a few kilometers, until I disassembled my motorcycle to check the clutch, it seems to be bad, although my biggest concern was the oil, I did not know that this happened with it, and Nowhere could I find information or data that indicates that it can be burned by the clutch, and I see that exactly the same thing happened here, did you also change the filter?

Nice vibe and nice bike

That tractor is a work of art!

On the right side of the LT 1050, there is a notch where the right support goes is very small and sometimes the support wants to go with the deck.

Technical term is a "Woolly Aphid", but as someone else said people call them flying fairies.

In northern Illinois, we call them “flying fairies”. They’re quite common in the summer months! Another amazing creation of God!

Help me figure out what this is? There is a few of them

Great video makes changing belt easy!

great video! curios to know since you removed the tow hook can the brush guard be used as a recovery point?

lovely people in a lovely land, would love to have such a sense of community

nice work lads!

Thanks man) 🙏

Damn what sawzall blade was that cut like butter 😅

By far the easiest way to do it! I don’t think people know about that drain plug because I certainly didn’t. Btw, if my washer starts and then turns off, what could be the issue?

I think the red o ring floats on water giving a visual.

Danke für das tolle Video. Grüße aus Kaiserslautern Germany