Видео

Ist da auch ne flex verbaut 😂?

Good job.

아주 성능이 뛰어나고 디자인도 멋진 장비 네요 저도 보유하고 싶습니다

Hey guys, how do i swap the other side bearings? from the outside or from the inside? cheers

How do these chain knockers work on soft poop stoppages

What they failed to tell you in the video are the cameras limitation, in real drain inspection scenarios. The cameras can’t pass more the 3 bends or 3mtrs. I know because I have one.

Ça passe toujours facile dans les salons mais la réalité est toutes autres dans des canalisation usagers 😂

you made stunning ,

gracias pedro

super

All well & good, but what does it do?

will it cut beyond liner?

Is there any data sheet or manual how to do that would you provide me?

Hey mate, for how long you allow the glue to dry after applied? Would that influence in the strength of it? Cheers

Ok im sold.

*promosm* 🙋

Ya we have those Geberit ball shaped fittings here in Israel. They're a pain in the butt 😂

Damn, that's a fine looking piece of equipment right there 💪🤩😎

What kemikas/fat or what do you spray inside?

Vilket tryck användes?

Kan ni skickar flera bilder på insidan av eran bil/Van? :)

That shit barely comes out

Too bad it's super thin liner and no epoxy in the lateral. Still a real good tool. We use it all the time. Highly recommend getting one. Mr Boldan, When will you put cutting heads on the back to stop it getting stuck after pushing through. To help retrieval?

Good video. The music made me anxious. Very annoying. No real need to make me feel like I was on an indy 500 race track. It would be great to have captions on points of interest perhaps even a question as to why you would need this and what problem it solves. The practical application. I liked the nice wide views. Nothing is hidden or needs to be figured out. Give the video guy a raise!

How the calibration hose removed? When the liner polymerized.

There's no fucking way I'm trusting that

I want to work in the arctic. I'm a pipeliner

Very nice!

How much would that cost to have installed.. I'm having a job done right now and they quoted me $3500

How much $$ does that t sock cost please.

Nice installation

Should make this applicable for sewer machines. To retrieve blades and chucks. Instead of using the pig tail method. Would be alot easier

Lining from the branch is so amazing.

Curious how many pounds of force those grippers have. I’ve pulled out a 4-foot length root mass by using an auger bit but that one looks like it might work as well.

Is this Tear away used so you don't need to invert a the cal tube into the liner for curing? Also known as a liner end cap?

When are you making the video where Juhani shoots Petri like a human cannon out of the extruder 2000? 🤣

what is the brand of your glue does it support the heat of the steam engine?

👌

So awesome! Does the tail of the liner ever get cut off so you can install the cal tube beyond the liner for water curing?

is it suitable for pvc pipes?

great video, however how do you wet out the liner with the rope inside??

Awesome product!

How many feet can the cable extend?

just curious, what sewer camera are you using in the pipe for the video?

Hola muy buen vídeo se ve claramente como entra y hace el codo sin problemas 👍🏼👌🏼 .Una cosa estoy pensado en hacer mi propio canal aquí en España , ya que hay poco conocimientos de este sector y así dar a convencer todas estas técnicas de reparación y materiales, sería posible que me pasarais un enlace de donde podría comprar esas tuberías transparentes que salen en el vídeo para poder hacer mis vídeos explicando como funciona el sistema y si sería posible que me mandarais alguno de vuestros productos para exponerlos sería más que genial. Gracias este es mi contacto info@tubetec.es .