Видео

very nice explanation for new HVAC TECHNICIAN Thank you

thanks

Sir smd jinar ka kese pta kre Kitne volt ka hai

@UATechnicalSolutions, could you help me for 30HXC? I have a Moxa 2-wire RS485 to USB converter, and the Prodialog 4 basic board has a CCN board. Will it communicate with RS485?

Very useful, what if you didn't have a diffuser? Asking in relation to centrifugal propeller design for aircraft application.

I noticed that DIP switch #3 was off on these, which relates to the communication speed to the indoor units. If this was a new install and all of the indoor units are 4th gen units, how come you have DIP switch #3 off? Having it on will allow the units to communicate faster and more reliable. If needed, I can give you the procedure for setting it as it has a few steps involved to fully switch it to gen 4 mode.

That's really a good video with this video I easily understood centrifugal compressor....thank you so much for this video ❤

Great 🎉

Whata wrong with using the terms anode and cathode?

Thanks 👍 for information

Thank you for the video, can we adjust the superheat for the outdoor

Hi I can't connect to my chiller via winloader can you help me to get the connection manager app

Thank you.❤

Thank you very much. I would like to know how to connect the main board to the computer and how to configure the Prodialog controller for Chiller Carrier 30G/30H.

30xa chiller, problem generate suction pressure transducers alarm again and again ,after remove another fix but same problem generate,what cause please tell me

Hello dear can you tell me which bearing number use in this compressor??

Please upload the video how to programme Mother board.

The videos are so helpful. I would like to ask , is SCPM board need programming or no.

Plz upload chiller video carrier 30xa or York Yvaa/yciv

Which parameters will be involved in COP of R-134a calculation ? When this refrigerant is used in the chiller i.e., Condenser temperature and pressure or Evaporator temperature and pressure???

Thank u for the best video

"How to remove AC condenser fan motor bearings with tools you don't own and then not put it back together again"

Thank your videos Sir this how we get user manual

Very informative video… sir pls upload a video regarding Trane chiller RTAC Communication how it’s works.

Thank for nicely demonstrating.

Thank you for the video

Pleaee Mark the gas suction & Discharge point, & how does conimizer work

Большое Спасибо за предоставленный материал!

Большое Спасибо за предоставленный материал!!!

🎉🎉🎉🎉🎉

nice...

I've seen some of those sensors can be calibrated. Have you tried that?

Nice videos! Keep the good work! Are you planning any future videos on vsd?

How to check igbt York vsd chiller

Yes .. normal useful video ... No blabols... Just data strict .. Nice vid

Very helpful, thank you

Quantity of oil 30xa 902

Reference oil of compressor plz

Hi Sir, In a carrier 30 XA chiller, when is there a need to replace an oil level switch ( float switch), can you please explain exactly. Regards Derek

Thanks for your help

😮

❤

+++ !

can you go over understanding the prints on an AHU. How to know exactly where devices are going on the ahu by looking at the print

What about when you get the "unable to read from selected device" error on a new sensor and nothing seems to make it read? It says it's not communication but I can turn the LEDs on and off.

Tengo el servitool pero no logro conectarme a mi chiller, puedes ayudarme?

Please make more videos of full training of trane rtac and centravac centrifugal chillers thanks.

👍

Looks like through hole type.

ruclips.net/video/419WoOpJOIc/видео.htmlsi=kPAxlwfPzPD4fTvz