- Видео 9
- Просмотров 425 720
Andy Speck
Добавлен 22 окт 2013
Fitting a CHRA Turbo cassette, are they any good????
Here is my real life experience fitting a cheap EBay turbo cassette or CHRA to my Peugeot 308 1.6 hdi blue 100BHP 49172-03000. Fitted on my drive with basic tools in a couple of hours.
Просмотров: 25
Видео
Head Gasket Failure Big Time XJS Jaguar
Просмотров 3445 лет назад
Xjs Head Gasket Fail, just filled up with water and 3 Steel Seals
Dodge Viper ASD Relay auto shut down 2004
Просмотров 2,7 тыс.6 лет назад
ASD issue resolved- Im sharing as there isnt much info out there.
Après avoir cherché pendant un bout de temps, votre vidéo a résolu mon problème, un grand merci 😁
this worked perfectly for my 2011 Peugeot boxer. cheers (y)
Tried all different fixes on RUclips dor my 2010 Peugeot Boxer, finally this one worked, van has exactly the same dash as pictured whereas some had slightly different.
Thank you Sir you are a legend !
Hi I just brought a citreon relay luton and it has the "Car and Lock light on dim" It lock unlocks starts and runs fine. Do you have or anyone else on here have any idea. Thanks for an informative video
Standard issue with that dash cluster. It’s only the light leaking through nothing to worry about. Mine does it.
@@andyspeck1386 Glad to hear its nothing serious but can the leakage be stopped cos im goin to try and sell it cheers
New cluster I believe
Thanks a lot
Thank you very much
Any ideas how to get my engine warning light off. I’ve spent thousands and vehicle around 200miles after a reset pops the light back on. No limp mode just a light, it’s obviously fishing voltage pings around that mileage and comes back with this every time
Fair play pal.. iv tried loads of videos and yours actually worked... cheers
Hiya. Did you ever solve this issue? I've got one doing the same thing, knew I should have got a newer one before something went wrong 🤦♂️😂
Under bonnet fuse board
@@andyspeck1386 Wow, didn't really expect a reply, and certainly not so fast! Thank you man. Was it corroded? I presume you changed it for a replacement? Thanks again, that's a massive help!
Worked on my 2006 boxer 2.2 hdi! thanks alot!
Followed exactly and it worked on my 2010 relay
Hi there what's the other light opposite the seat belt light..
Side door
Door open light.
Put Tape in to the side door switch, then light goes off and then the automatic locks works too 👌 You find the switch behind the side door car.
on a puegot boxer slightly different. 1. with ign off hold down both acxelerator and brake pedal. 2. after 20 or 30 secs turn ign on until oil lights start flashing. 3. turn ign off and release pedals.. done
how i reset check engine light?for opel astra k 2017?
it works 100% at my citroen jumper 2.2 hdi 2009 you are the best💯👏
Please subscribe for more Relay videos
Worked a treat on my 2007 Citroen Relay, thank you
After 9 months and numerous mechanics trying to permanently clear my engine management light on my Citroën relay and failing miserably,this worked!much appreciated.
Genius!! Thanks buddy!
Did the steel seal work?
Thank you
It was working in UK at citroen flat bed from 2014 cheers man!
Citreion rellay engine managment light on and in limp mode temp on zero and fans on has anyone any ideas how to fix
eng man light on
Relay 1000 TD HDI 1997cc - Followed the instructions and it cleared the ENGINE warning and LIMP HOME by the Engine Control Module. What concerns me is this system is used on a number of new aircraft, Saab, Embraer etc.....
2010 relay. Didn’t work
Thanks for that video , I can now switch off that d!! light. Brill
Thanks mate.
May have solved my P0603. After swapping out the ECU, buying a new fuse box, basic checking the wiring and checking the battery.. none of these solved the issue on my van. It got so bad the van cut out on the road! Took the van to Citroen main dealer. They set the ECU back to the factory standard for the van. They also check the battery earth but this must have been OK they reckoned as the van always started / restarted. It is now believed the remap done by a private garage was trigger for the P0603. The remap had been removed by the private garage and it was at that point the error surfaced. Since the reset of the ECU today the MIL is now out and has not reappeared after 100+miles. So far so good!
So still an issue in the ECU. Reset or reload of software did the trick as I understand.
@@hsmautoservice158 Sadly no... it didn't work. The fault went away for about 100 miles, then left overnight on restarting the van the MIL and fault have come back! Gutted. Looks like a full new loom is the next step with the dash out 2 days work £2,000. The reset flash to factory default hasn't helped. So the ECU, fuse box, re flash, cleaning of contacts are still cause the Keep Alive Memory Module error P0603. :-(
@@dickieschannel1465 Try measuring voltage while starting. If it drops under 10v, that might also set the code
@@hsmautoservice158 OK will do ... Interesting idea. Assume you mean directly across the battery terminals? If its below 10v does that suggest the battery or alternator? I did try the van with a different battery and it didn't seem to make any difference. But will get back to you ... thanks for taking time to comment on this; much appreciated its a bit desperate at the moment and I don't really fancy replacing the loom!
@@dickieschannel1465 Might be battery, but also possible is a starter taking too much amperage. The ECU itself was replaced? Since that is the most common cause for the fault (and results)
Ebay item 273561707333 Unbolt the cover, it's on a hinge 3 plugs and one nut holds main cable on. Theres a main relay in the middle.pull that out and see the terminals will be corroded. Dont waste time with a second hand one.just check your part number is the same.loads have been fixed this way
Thanks for that, have ordered and fitted a brand new fuse box. Still no joy with the error started it up and it just comes back ... gutted. So it must be somewhere else. Have also had the ECU cloned to dont think its the ECU. Will keep looking but loathed to take it to a main dealership.
Hi, I have the dreaded P0603 error and MIL. Did you get this fixed Andy? Or has anyone got a solution?? I have tried a second ecu and this didnt fixed the problem... am struggling a bit with it now. Citroen garage are quoting £100 an hour just to take a look at it!!
Hello Yes in the end. The fuse box under the bonnet is damp and corroded. A new one is £100. The part number is on a label on the side of it
@@andyspeck1386 That's very helpful .... just to confirm is it the fuse box on the UK passenger side just in front of the ECU? Assume you mean the panel that tips up to reveal the connectors underneath? Was corrosion obvious on the outside of the box, or inside the fuse box connections? I'd be over the moon if I can solve the DTC with a new fuse box :-)
Nope...bought a new fuse box, fitted, still the same fault. Worth a try though. So think its off to Citroen next week ... not that I have much faith in them :-)
@@dickieschannel1465 Fixed? It's a code of the internal memory of the ECU, so most likely the problem lies in the ECU itself. I say most likely, since unfortunately there are also things in car-land that are not so straightforward
248601 miles is 400, 000 kilometers.Fiat who made the ecu decided a commercial vehicle would not need to travel more than that. So odo stops at 248601.No known fix
What a punch of idiots so it's a new ECU or can I av it reset ? Thanks andy
Sorry bunch lol
Hi Andy, did you ever sort out the error p603?
Thanks my man 👍👍👍
Brilliant, thanks. Is there a way to see the count down to when the light will come on?
Is it 248601 miles ?
Yes Andy it is mate . So you saying that you must know something lol?
Hi thr I've got flashing mileage on my 2008 2.2 relay .also it dosnt clock up .. any ideas
Is it at 248601 miles by any chance🤣
Yes Andy it is at said milage.
Do you know why the clock is flashing? I am having the same problem and no luck finding anything online
many thanks
thank you.
Merci beaucoup !!
Khouya xrh had Vidio hik 3ndi nfs lmochkil
Nice one mate worked a treat on my 2013 relay! Thank you!
Brilliant, sorted! Thanks!
Brilliant!
Thanks man from greece it works!!!!
Thanks Andy, all the other reset videos don;t work, this one does. Peugeot Boxer 2012 3.0L HDi engine. :-)
Hi I did this to reset the flashing oil light. However it doesn't reset the service spanner or the oil count down bars on the dashboard. I have the service spanner light on can't find the fix anywhere.
They're not countdown bars. They are quantity bars. If you don't have 5 you are low on oil. if you have 5 flashing, you are overfilled.
Thank you man
You are the best bro thanks. 100% work.
Citroen relay 2.2
Thank you very much for sharing. It worked for me. Regards
Nice one!