- Видео 86
- Просмотров 75 079
Odins Lock LLC
Добавлен 28 июн 2018
Locksmithing & my Van Build info. Check out my other main Odins Lock channel at ruclips.net/user/bobhdus for more Stepvan stuff. I’ll be migrating back and forth depending on the topic. Email: bobhdus@gmail.com or asgardrules316@gmail.com
4L80e and B&M Shifter issues
Having problems getting my linkage hooked up on the 4L80E. For some reason I’m only able to go into 6 gears. It’s possible the tranny is in a bind from being on a hill and I might be able to rock the Stepvan or lift the rearend and rotate tires a bit. But the shifter cable bracket also doesn’t line up with the bolt holes on the tranny pan. I sent message to B&M to see wassup. I’ll post update when I get it figured out. From what I understand most people don’t have this problem doing this retrofit so must be a unique situation I’ve found myself in. Sorry for the narrow frame format. I caught that too late and didn’t have time to reshoot. If B&M can’t help me then I’ll make my own bracket, ...
Просмотров: 124
Видео
Stepvan 4l80e crossmember
Просмотров 97Месяц назад
Stepvan 4l80e crossmember is installed and now the next steps I need to take to get this back on the road.
4L80E Output Shaft Seal Install
Просмотров 1892 месяца назад
Had to install the shaft seal on the new donor 4L80E tranny before I can install the driveshaft. First part of this is when I tried to install the seal and it was incorrectly packaged (correct box, wrong seal). Second part is with the correct seal. Thanks for watching, please like and subscribe!
Stepvan Engine Swap Progress
Просмотров 1413 месяца назад
This is not a locksmith video. It will go in my Stepvan playlist. Update- Finally got the rebuilt SBC and the new (used) 4l80e tranny. Slowly getting everything put back together. I had to cut out the old driveshaft (it was 50 yrs old) and was able to drop it off at our local driveshaft repair/ rebalance shop to have it cut shorter and all new u-joints and carrier bearing installed on it. The s...
Bravex Rekeyable All Mechanical Deadbolt
Просмотров 1603 месяца назад
This video is a quick review of the newer Bravex Rekeyable All mechanical Deadbolt. This is the short video. There is a longer one I may post later as I still need to do a little editing with it and because it was the pia version to record lol. I may not post it. If I do it will likely be unlisted and link only. It was also filmed before I could check the fit up on a customers doorway. Bravex a...
Last drive & pulling engine
Просмотров 7593 месяца назад
This isn't a locksmith video. I'm gonna start posting my stepvan project type videos on my locksmith channel so my subscribers on both channels can see all my content. I will of course create playlists if you want to watch from a specific category. Ill update stuff in the description or pin corrections or updates in the comments. Thanks for watching. Please like and subscribe.
Framon & SFIC 7pin
Просмотров 2574 месяца назад
First off, my gopro sucks! Sorry for the volume issues. Anyways, this is the last of the BEST/ SFIC vids I'm gonna do (for now). Pretty much covered most of the SFIC key making. In this video I mess up on the last cut and I'll show you what you'll have to do to make it right the first time since I didn't. Btw, I don't think I've ever cut BEST 7 pin on this machine. Usually only do 6 pin and the...
HPC 1200 and SFIC Keys
Просмотров 3664 месяца назад
Cutting a BEST A2 SFIC 7pin Key on a HPC 1200. I didn't do any editing with this video. The GoPro I use has issues with the microphones. There's 5 of them and when I use the protective case it interferes and causes weird volume issues (too muted or too loud). Editing requires transferring from one device to another for editing then back again then uploading. I was able to do this all in one tak...
PCH Punch Machine & SFIC Keys
Просмотров 2224 месяца назад
In my previous occupation I used the KABA Ilco MK2 Punch, PAKAPUNCH and the Foley-Belsaw Model 200 for originating BEST type SFIC A2 keys. This video is the first time I've used this HPC PCH Punch Machine to cut a BEST type key as I usually used my HPC1200 or Framon 2. I picked up a couple of these at a decent prices and keep them for when I don't have access to power as these are mechanical Pu...
BEST IC Servicing Option 4
Просмотров 7294 месяца назад
There are 3 techniques that are commonly usually used when dealing with BEST type A2 IC locks that do not have a working key or ability to remove the core. 1st option is to drill control lug retainer thus allowing to decode the IC but will damage or destroy the hardware. The 2nd option is to drill the pin stack to allow forcing the control lug to rotate for removal which destroys your ability t...
Stepvan drive along
Просмотров 3,7 тыс.5 месяцев назад
I posted this once already but yt hit me up for music copyright issue so heres the video without the music. I use this stepvan for my locksmith business. Its a 1974 GMC Value Van 14' , P3500 to be exact.
Foley Belsaw Model 200 Capability
Просмотров 4626 месяцев назад
This is about the old reliable Foley Belsaw 200 and what keys it can cut. Foley doesn't sell these anymore that I can tell and in fact their locksmith course now offers the Speedex mini with the completion of their course but they do ofer all of the replacement parts and that stuff is available at other sources as well. The model 200 is not heavy duty per se but it does have a lot of capabiliti...
Got one at an estate sales. What should I sell it for? Thanks
@@vickygarner9479 I really wouldn’t know. Depends on what accessories and key blanks with it. It’s more about what someone is willing to pay. It’s a wonderful machine if it has everything but in pieces it may not be worth as much. You might check eBay and see what they’re being sold for. I personally would pay more than a hundred if it had everything but someone else might pay $300. It’s possible to cut by code and as a duplicator it’s easily adjustable for new or worn keys. The biggest issue I have with them is the clamping jaws. If those were more robust these would be worth so much more. A maintenance dept or apartment maintenance type place might be interested in it or a locksport person. Most locksmiths would already have this machine and no room for another that won’t get used as much. Clean it up and have it “ready to go” and you will get more for it.
thanks for doing a video on this...there is one selling locally...might pick it up...good for vintage VWs :)
After some serious obsessing over it I think I figured out that I need this kit- B&M 75499 Cable Bracket/Shift Lever Kit, GM 4L60E-4L85E Rear Exit I ordered it and will do another video when I get it figured out. I never did hear back from any reliable tech support from any of the suppliers of the B&M shifter…
Great plan 12:13
Great job 10:52
Man, that looks beautiful good job clean as a Pin
Thanks 👍
@@odinslockllc thank you buddy
Oooh an orange padlock
Great content Sir
❤
If You Want A Belt That Will Out Live You Install A Sewing Machine Belt Like I Did When I Had A 200 Over 30 Years Ago. It Will Be The Last Belt You Will Need.
Great idea! What particular part# or size did you get? Thanks for watching!
so true....the orange sewing machine belts are a amzing.
Never a dull day
What are you doing step van?
My original v8 engine had a wiped out cam so I put in a straight 6 that I had available until I got around to rebuilding the original engine. So with putting the original engine back in I opted to find a transmission that would get me better gas mileage especially at higher speeds as the stock tranny was geared for inner city driving back in the 60’-70’s. So with that I had to make a bunch of other modifications. Probably pretty boring to watch for a locksmith channel. I usually put these videos on my other channel which was just about my Stepvan but figured there’s a lot of people on this one that might like older work vehicles. Thanks for watching!
Coming along nicely. High tech ignition systems may be nice and fancy, but the less electronics, the less headaches and points of failure.
Thanks! Agreed as well on the ignition. It’s mostly cause I’m cheap and the old stuff works fine though. I have a points eliminator by pertronics but don’t want too much different new stuff for the first startup on a fresh motor. Once it’s going I’ll upgrade more stuff. I just want less stuff to troubleshoot if it doesn’t start or run like it’s supposed when I finally get it going. Thanks for watching!
How in the World did you get that bad boy in their good job
It was crazy lol. The cylinder on my engine lift blew the seals right when I was lifting it into the Stepvan so I had to rush to harbor freight and get another one. Thankfully they had one in stock and I had it all swapped within an hour and the engine dropped in 30 mins after that. Smooth…
Nice job
I just bought out a locksmiths estate and got a 1200 blitz a key duplicater and a bunch of key blanks definitely going to start a side business i love to 1200 blitz machine
Great find! It’s a wonderful machine. You should get a calibration kit if it didn’t have one.
@@odinslockllc any tips on getting decently priced code cards?
whhhhyyyyyyy did they not use a standard cylinder ??? I sent them the specs they needed a while back for it 🙄
Yeah I had a pile of cylinders and some fit and some didn’t. With a some slight modification most 5 pin will fit. I told them they should at least carry the cylinders they say will fit.
A need little camera, nice and compact. I don't know anything about these things, cheers
Thanks for watching!
I've got a hero 9 with the mod kit for the microphone jack. The display has a sound meter at the bottom that I check to make sure the mic is working regardless of ř recording or or doing the quick record. But there are enough problems the gopro that I'm looking for a regular camera to use.
I’m at a point where I may use my old iPhone to record only then airdrop to my computer or other iPhone for editing and uploading. Thanks for watching!
Can’t help you with that it’s the first time I’ve ever seen one up close good job though on your video. Nice to see you having some more fun with high-tech equipment here in the USA.
Hooray, you’re finally showing us the goodies
Was just informed that the retail price is $130. Wholesale price is offered to locksmiths and is less. Also wanted to mention, you will need to verify the cylinder dimensions you want to use as not all will fit due to varying sizes. Some modifications of cylinder may be necessary. A few that I check barely fit but would with some minor sanding and tailpiece changes.
Your sound is 100% better 1000% better 26:54
What was the space from the shoulder to the first depth the center of the first depth what was that space again now you got me wondering
I found a fast way of finding the depth and spaces by using HPC master king software every key in that software has depth and spaces and if you want to take the time you can look through until you find the one you’re looking for I had to do that the other day For lousy mailbox key
You’re very talented
Nonsequential
I think the only mechanical push button deadbolts on the market that are “sequential” are the simplex brands. All others are “nonsequential”…Definitely important to know…
That’s funny nightmare, ha ha ha ha
Hahaha🤣🤣
🫵🤾🏻
You’re welcome little buddy sound is everything if you’ve got horrible sound no one’s gonna watch your videos but now you’re past that it sounds great no rubbing popping. Slamming crunching sounded wonderful hurray for you.
Im almost fiddy four years old. Some of that popping crunching sound may be coming from my joints🤣🤣
ruclips.net/video/rxEIqaz1Zdc/видео.htmlsi=TxSs9NT97zsXLAoj this is a beautiful place in Winston-Salem. I just finished had to order more locks though. I think you’ll get a kick out of it.
This sounds great good job
Yeah, that does look like a nice lock so you don’t know the price yet huh?
Did you get the DJI mic
I got the rode video microphone. I was having problems with it not coming on for the audio but I think figured out that it won’t work with the quick record feature. But if I already have the GoPro on then hit record it will work. Idk why it’s like that🤷🏼♂️.
Hey, the sounds better. What did you do?
Got the microphone adapter setup for the GoPro. I think it’s gonna be better now. Still a few things I need to figure out with the settings… Thanks for the information you gave me about recording.
Man, how do I sign up for free stuff!?!? Looks like a solid setup. Thanks for showing how quick these are to install.
I’ll tell her to contact you. I think your email is on your channel description?…
Hooray for you🎉
I’m going to try to merge my videos onto this channel from my Stepvan/ projects channel so I don’t have to grow two different channels and some of my subscribers are on both so it’ll be easier to keep track of what gets posted. If you haven’t yet please like and subscribe, thank you for watching!
if you figure out how to do that let me know I have a dead channel that has thousands of hits on my old pictures videos and I would love to get those Numbers on my new channel but have never been able to figure out how to do that💰
@@doorandlocktips I think in YT studio you can download and reload onto new channel. But I think you need to do it on a computer.
@@odinslockllc thanks
You definitely made a ton of progress. Can't wait to see it come together.
Thanks, yeah I’ll be glad when it done 😅😅🤣. Thanks for watching!
Awesome video! I have the Punch Machine and noticed the issue of there being a delay in the space needle moving when you go back. P.S. Have you had problems with double-sided auto blanks slipping out of the vise or rubbing against the die?
I haven’t done any double sides cuts in it, (I don’t do any automotive keys), but I notice there is an issue with backlash. Thanks for watching!
These remind of the 1977 Commer/Dodge Walk-Thru vans that Royal Mail used to have in the 1980's. Oxford Diecast makes them in 1/76 scale for anyone that is interested. Although they used Renault engines. I wouldn't mind owning one of these with a Renault Magnum V8 engine as used in their trucks.
Please don’t judge the Framon based on my experience. This video series with the PCH Punch, HPC 1200 and Framon was really about the complexities of cutting sfic or BEST type keys. It’s a little more complicated than cutting Schlage/ Kwikset as sfic blanks are usually harder material, sometimes don’t fit flat and can have 6 or 7 spaces and accuracy tolerances are tighter with the smaller pins. Right out of the box Framon will cut 7 pin but you gotta count out to the 7th. I almost stopped the video when it didn’t work on the first cut but thought it would be better to troubleshoot the issue on camera. The HPC1200 won’t cut 7 pin right out of the box (must buy the 7pin card) only 6pin card is in the set and the micrometer card may not be that easy to read the graduations with this tight a tolerance. Thanks for watching!
Thanks for sharing, hey off topic almost on topic question. When widening cuts with the framon I’ll take bites with it then drag it across in hope to reduce the strain on the blade. Good idea or waste of time? I’ll take a bite middle one to the left, one to the right and then slide across. For deeper cuts it definitely sounds like it’s making it strain less. Just curious your thoughts, technique should also work for the HPC.
Actually for the hpc1200 they recommend you start on one side of the cut then widen to the other side. Look at the short I just did, I’m gonna say follow the directions. I usually would go back and forth but according to the 1200 directions that wrong to do. If I were cutting nickel silver I’d definitely be more careful as it’s harder material. These cutters are more designed for straight infeed cutting but a little side cutting can’t be that bad, but idk. Look at the cutters on duplicators, they’re more designed for side cutting. Thanks for watching!
Sometimes instructions get it right...lol. thanks for sharing.
I hear the Framon is a great machine, but as I watched you cut this key I'm just not sure it's a machine for me. Now I've gotten a bit of fun poked at me, but my go to machine is still the 1200. I tried a buddies Futura cutting keys from my previous 10 jobs for a sampling of it. And yes I took into account the 'new factor' of just using it for the first time...just wasn't a fan. So far, after trying a few machines, I think the next purchase will be a Triton+. I'm probbaly only buying one more machine and possibly one more duplicator in my lifetime...so I better damn well like it huh?!?!😅 I know you have a 1200 down the bench, any reason the Framon vs the nice little needles on the 1200?
Framon is a wonderful machine and will do more out of the box than the 1200. But there are some cool additions for the 1200 like the tubular cutter attachment etc. I think it’s personal preference what you’re comfortable with. My “go to” machine is my 1200. The Framon is just as fast when you’re used to using it which I’m not because I normally use my 1200. The Framon would be better if the depth feed had just the graduations I needed for a specific key. I’m probably gonna make something just for that. The Framon is more accurate as well. It’s kinda like with calipers, I prefer dial over digital as everytime you see the digital readout move it seems like it’s a lot but in a dial it looks as if it’s less. Probably purely psychological lol. Benefits to digital is inch to metric switch is push of a button. Thanks for watching!
Thanks for making another video.
Thanks for watching!
Great video thanks for sharing! Do you find that double sided works any better than the original vice? I’ve been on the fence about buying them or just investing in a blue punch
I think it does but as you seen you really gotta pay attention to the changes with the starting cut. Personally a blue punch for A2 is the best way to go all around. You can still cut sfic keys either way on the old jaws just gotta shim it sometimes. Just remember that 7th space isn’t on the spacing block and you gotta use the dial at .150 for that last cut. Thanks for watching!
It will buffer all that sound of the key cutter and I can help you set up the Rite numbers on the receiver. You will love it Bob and best of all I feel tested it for a year and a half. It’s phenomenal.
This will solve all your sound problems. You can plug it into your phone either an iPhone, or an android, then hook one of the condenser mics on you and plug the DJI Lavalier into it stuff the cable behind your shirt, the mic on your lapel or somewhere and you will have the best some quality known man.
Great job little buddy you are the man
Thanks for watching!