Видео

Did it sparks when u tried connecting the last wires.

Basically yes, it's called Loktite and it's pretty standard for screws that are going to be subject to lots of movement. Just takes a little more oomph, make sure you push hard into the screw and use the Allen wrench that came with the wheels to make sure you have the right size. If you ever strip a single screw that's a good sign to take a step back and rethink your approach, usually means you're using a slightly too small wrench/screwdriver or you aren't getting enough force into the screw. If they are completely stripped, you can go to Lowe's and ask for "easy outs", they'll point you in the right direction. You'll probably want a size 2 or 3, you hammer it into the stripped screw and use a crescent wrench to turn them out

Do you still have a belt on it ?

It’s a multi tool that comes with the board

Like 130 usd

I replaced mine when it ripped while riding lol, I think that's a good time to replace

If you want to use this Gear Drive on Envy, you also need to replace the Voyager motors on your envy.

Ooh so I need to get septet motors then connect them?

Only if you swap the motors to the voyager's motors, as the envy has smaller motor shafts

​@@everythingabout-esk8 I bought the Geardrive replacement kit with voyager motors for my NLS3, but they wont spin with the remote. do I have to change a setting?

​@everythingabut-esk8 what do you mean?

OK!

Thanks for your message, Voyager battery is compatible with Meepo Envy- NLS3 . But the battery case it different

Gear drive config protects from dust, rocks and small debris from daily use while on belt drive config, small rocks and debris easily gets caught up in the belts in result of belts snapping. So far I heard that it's much smoother than the belt kit and you might actually love its noise. It's definitely worth going for full gear drive power kit so you can easily swap over each gear drive and belt config back and forth.

Newer

Sure ! www.meepoboard.com/products/90-mm-hub-motor-for-v5-mini-5-1-pc

@@everythingabout-esk8 The link says 9 pin connector, but your video is an 8 pin. Is that still the same?

They do, just good to know incase you face any problems needing disassembly/ reassembly.

Thanks, buddy !

If so, that will always be me🤪

Thanks for your suggestion, we will feedback your suggestion to our video maker

Quick update: It can be compatible with 105mm / 120 mm Cloud Wheel

www.meepoboard.com/products/120mm-cloud-wheels-for-hurricane?_pos=1&_sid=8ea5d6941&_ss=r www.meepoboard.com/products/105mm-cloud-wheels-for-hurricane?_pos=9&_psq=105&_ss=e&_v=1.0

I believe it should be the same because meepo sells batteries for the mini 5 on their website, the er battery, and normal battery.

Yes, Mini5 battery is also removable

wondering the same

I believe it’s so you can use the 150mm wheel kit that Meepo sells for the voyager and the envy. The voyager already ships with the update.

I think I have an answer. What I think is it has to do something with speed control. The board itself moves translationally, meaning it is moving on a straight line. However, the wheels are spinning. The controller has no GPS unit inside, so it can only know current speed by knowing RPM of the motor times circumference of the wheel, hence getting the linear speed. Right? If you just slap 150mm off road wheels on it, the controller will 'think' you are going, per say, 10 mph for 'native' green wheels this thing has (i think they are 90mm, whereas you will be going 150mm/90mm * 10mph ~~ almost 17 mph at this point! You need to tell the remote what kind of circumference of installed wheels is, so it could calculate speed accordingly.

@@kilovolt2494 what were to happen if I did this without the AT wheels? Does it give a speed boost?

@@WookedSun yes and no. I think these motors are limited on current, so certain current gives you peak power, regardless of gear ratio. If you reprogram your remote to higher gear ratio while using standard 90mm wheels or Cyclones-well, first off, your speed reading will be incorrect to a low side. Second: your board might start accelerating abruptly, thinking that there is a large wheel to turn so it needs higher RPM. All speeds would be increased compared to standard setting, yes. Standard gear ratio for 90mm pus is 2.1. Try to set it like 3 and see if there is any speed boost. But then deceleration will become also sharp!

If it doesn't turn on, it means it was broken, you can contact info@meepoboard for a replacement if you are still in warranty.

Yes, works with any kegel pulley