Видео

I love seeing something that got thrown out and grabbing it and making something else out of it for sure.

@@haneyoakie14 free is good 😊

RUclips must have killed it

I have had that happen to me before

@@patthesoundguy all I said was “Free Ham mmmmm”. Sort of in a Homer Simpson voice.

@@patthesoundguy they nix innocent fun stuff and allow the pure bovine secretion aka BS.

Great question Bre!

There are some relatively inexpensive hand held 2m rigs. eBay and swap meets can offer “vintage” rigs, stuff that uses tubes and not microchips…if you are worried about an EMP. You can build loads of antennas that work great for very little. RUclips has loads of videos that can show you lots of options.

The question is are you looking for communications?

@@ernst2able it may take a bit of trial and error, and I would try a little lubrication on the rubber. It can take several tries to make sure everything is all lined up. Don't worry you'll get it 👍 I think it may have taken a bit for me to get it right

@@patthesoundguy Thank you for the. encouragement I'll give it a few more tries. This chainsaw has a very special build up that I've never seen before.

@@ernst2able you'll love it when you get it back together, mine is one of the go to saws in my small collection. It runs like it's ported. Ii was going to maybe do some port work on it but it's so good as is, I have left it alone

@@patthesoundguy I wish you the best of luck and send you some late summer greetings from the Åland Islands in Finland.

@@ernst2able Thank you my friend, great to hear from you. 😄

@@JerryBenson-u7j I am so glad I could help you out! That is the kind of problem that could lead to very expensive diagnostic fees and never find the problem.

@@duaneshuster6366 RUclips did that... I think it is an algorithm thing where it thinks I was trying to advertise or something. No matter how much I tried to re-upload the clip it would flip it in RUclips. It went in right side up and I even re-shot it a few times and thought it was me.

@@MegaNostr from what I have seen with brass copper should polish the exact same way. Brass polishes in like 35 seconds, it's like magic

@@patthesoundguy Thank you

@@ODB_ doesn't remove the dust and dirt, but it would definitely remove the pills for sure.

@@tonycooper3616 So glad I was able to save you some headaches 👍👍

@@RobBot34 I only showed how to remove the limiter caps, it doesn't take long...

Thank you so much! I'm very excited! The exam was the first test/exam type thing I have done since June of 1996 so I was quite nervous and studied so very hard.

@@Wadejm533 yes this is a full replacement of the brake material. If you aren't missing any parts you will have full brakes when you are done. Thank you so much for the comment. 👍

@@patthesoundguy will I have to do both sides?

Do you mean both brake pucks or pads? There is an inner and an outer and it's probably best to replace them both if they are worn out, It would be good to go through all of the parts and clean the caliper up and clean the pins like I do in the video, just in case everything being seized in place is part of your issue.

@patthesoundguy no. I mean both back tires, do they brakes.

@Wadejm533 there is only one brake on the side of the trans axle that works both wheels.

Back then it was close to $1,000 Canadian so not cheap. If he had checked the oil and changed it when he was supposed to it would have lasted longer than 3 years that's for sure

They are audio pipe if that also helps

What you seek is called a re-cone kit... It will have new voice coil and the paper cone and new surround and such. It takes some skill and practice to do that job if a kit is available for those woofers. It can be done DIY with videos and there are websites that sell everything to make it happen. I would see if there is someone near you that re-cones speakers, people that do it all the time can often measure the broken parts to know what generic kit can be used. Depending on the woofer it may be more cost effective to replace them. The most common cause of woofer failure is running the amp into clip which makes square waves which makes the coil heat up and fail.

I use high temp silicone brake grease on the pins, antiseize doesn't work on moving parts they gum up.

Yup powdered graphite should work really well too.

Nah there's a chemical reaction with soda, it's stronger

It definitely might work. If it is plastic you need to rough up where the glue needs to go and then it can hold very well. I repaired my plastic ID card for work with this trick the other day. Roughed the plastic up, put some glue on the crack in the hole for the lanyard and put some baking soda on it, good as new

@@patthesoundguy thanks for the tip dude

My pleasure, hope it works for you. 😃

Those flapper disks are one great invention. I use them for so many jobs now.

Thanks so much 👍

I have been without a workshop since last July so I haven't been able to really make videos. The shop should be over the next month or so I hope. Then I will be making lots more content

Trust me it actually sounded like a new woofer but the shit sound you heard was the phone microphone crapping out from the extreme sound pressure levels that it could not handle whatsoever 😉 When that cabinet got returned to the rental shop at the end of the summer they continued to run it for a long time before they got around to putting the replacement driver in.

I've tried it and it's nothing compared to having it hooked up to the charger... It will clean the carb and remove some corrosion but you have to soak it for quite a while where it's super clean and corrosion free in 35 seconds on the power supply. The jets and other brass components come out with zero build up or contamination on them when you use the power and electropolish.

@@patthesoundguy thanks for reply. Good to know

Thank you so much for the kind comment, I'm so very glad I was able to help you save money.

That's a great question... I don't know for sure because I haven't had a set in my hands, but from what I experienced from working with the FRS version they should work because I was able to change my FRS to VHF with some success because I had the software unlocked. But there is no way to know for sure without trying it with the MURS version.

That's entirely up to you... A nylon brush will not be as harsh on the carpet