- Видео 19
- Просмотров 110 055
SB Acoustics
Индонезия
Добавлен 25 дек 2019
Built from the foundation of a company with decades of manufacturing experience and partnered with an engineering consultancy touted for their revolutionary designs. SB Acoustics was formed to bring an alternative to the high-end transducer market. Marrying the design talents of Danesian Audio (Denmark), a company filled with industry veterans, responsible for many well known and revolutionary designs, and manufacturing expert Sinar Baja Electric (Indonesia), a vertically integrated company with more than 35 years of transducer manufacturing experience. We feel we have been able to create an affordable line of products, without compromising acoustic performance for cost. Ultimately, we invite you to judge.
Satori TeXtreme Woofer, 9.5 SATORI WO24TX-4, Unboxing video
9.5 inch SATORI WO24TX-4
TeXtreme Woofer
Features:
- Advanced TeXtreme cone for improved piston operation
- Large optimized motor system with under-cut pole piece and dual shorting rings
- Vented aerodynamic cast aluminium chassis for optimum strength and low compression
- Soft low damping rubber surround for optimum transient response
- Linear symmetric suspension design for improved dynamic performance
- Non-conducting fibre glass voice coil former for minimum damping
- Long life silver lead wires attached 180° apart for improved stability
- Vented pole piece for reduced compression
- Low piston to chassis diameter ratio
- Gasket and bolt hole protrusions for reduced coupling to speaker cabinet
For ...
TeXtreme Woofer
Features:
- Advanced TeXtreme cone for improved piston operation
- Large optimized motor system with under-cut pole piece and dual shorting rings
- Vented aerodynamic cast aluminium chassis for optimum strength and low compression
- Soft low damping rubber surround for optimum transient response
- Linear symmetric suspension design for improved dynamic performance
- Non-conducting fibre glass voice coil former for minimum damping
- Long life silver lead wires attached 180° apart for improved stability
- Vented pole piece for reduced compression
- Low piston to chassis diameter ratio
- Gasket and bolt hole protrusions for reduced coupling to speaker cabinet
For ...
Просмотров: 3 393
Видео
NEW Satori Coaxial Driver, 7.5" SATORI MT19CP-8, Unboxing Video
Просмотров 3,4 тыс.11 месяцев назад
7.5 inch SATORI MT19CP-8 Coaxial Driver Features: - Vented cast aluminium chassis - Proprietary cone material with Egyptian Papyrus made in house - Powerful low distortion neodymium motor system with extended copper sleeve - Low profile triple roll rubber surround for minimum high frequency diffraction - Light weight CCAW voice coil on fibre glass former - Long life silver lead wires - Soft dom...
New Full Range Driver, 8 inch SB20FRPC30-8, Unboxing Video
Просмотров 7 тыс.2 года назад
8 inch SB20FRPC30-8 Full Range Driver Features: - Proprietary cone material with natural fibers made in-house - Light weight foam surround - Optimized whizzer cone for smooth high frequency extension - Phase plug for controlled radiation - Large spider for improved linearity - Optimized motor system - Vented reinforced plastic chassis - Non-conductive coil former - Long life lead wires - Extend...
SB Acoustics, building your sound
Просмотров 11 тыс.2 года назад
Built from the foundation of a company with decades of manufacturing experience and partnered with an engineering consultancy touted for their revolutionary designs. SB Acoustics was formed to bring an alternative to the high-end transducer market. Marrying the design talents of Danesian Audio (Denmark), a company filled with industry veterans, responsible for many well known and revolutionary ...
New Coaxial Driver, 4 inch SB12PACR25-4-COAX, Unboxing Video
Просмотров 3,8 тыс.2 года назад
4 inch SB12PACR25-4-COAX Coaxial Features: - Vented reinforced plastic chassis - Anodised aluminum cone - Low damping rubber surround - Large motor system - Long stroke linear suspension - Light weight CCAW voice coil - Non-conducting fibreglass coil former - Non-resonant long life lead wires - Compact large surround dome tweeter For more information please visit: sbacoustics.com/product/4-sb12...
SASANDU, Black high gloss, Assembly process
Просмотров 10 тыс.2 года назад
SASANDU, black high gloss, assembly process Frequency range: 32-32000 Hz /-3dB Sensitivity ( 2.83V/1m ): 89 dB Nominal impedance: 4 Ω Max SPL: 108 dB Cross-over frequency: 480/ 2800 Hz Enclosure type: Bass reflex (woofers), sealed (midrange) Port tuning frequency 32 Hz For more information please visit: sbacoustics.com/product/sasandu/ Don’t forget to like, comment and subscribe SB Acoustics RU...
Shallow Subwoofer with Light Weight Design, 10" SW26SFC38-4, Unboxing Video
Просмотров 2,3 тыс.2 года назад
10″ SW26SFC38-4 Shallow subwoofer Features: - Shallow light weight design - Hard pressed vented paper cone (made in-house) - Inverted low damping rubber surround - Symmetric suspension - Stacked neodymium motor with built-in soft limiting - Non-conducting fiber glass coil former - long life lead wires For more information please visit: sbacoustics.com/product/10-sw26sfc38-4-paper/ Don’t forget ...
2.5 inch SATORI MD60N-6, Dome Midrange, Unboxing Video
Просмотров 6 тыс.3 года назад
2.5″ SATORI MD60N-6 Dome Midrange Features: Coated non-resonant soft dome Powerful neodymium motor system Tuned closed-end transmission line chamber Dynamic dome stabilizer and flow resistor Machined aluminium faceplate Vented coil former Braided long-life silver litz wires For more information please visit: sbacoustics.com/product/2-5in-satori-md60n-6-fabric/ Don’t forget to like, comment and ...
SINAR BAJA ELECTRIC, Company Profile Video
Просмотров 8 тыс.3 года назад
Sinar Baja Electric is the largest speaker manufacturer in Southeast Asia and a significant player on the international market. Our products and services include all types of speaker drivers as well as turn key speaker systems, fully supported by in-house facilities and competencies. for more information: www.sinarbajaelectric.com
SATORI AT60NC-4, Air Motion Transformer, Unboxing Video
Просмотров 4,7 тыс.3 года назад
SATORI AT60NC-4 Unique new air motion transformer by SB Acoustics. Features: Precision diaphragm assembly Unique foil damping Optimized rear chamber Two part faceplate Smooth controlled dispersion Very flat impedance curve For more information please visit: sbacoustics.com/product/at60nc-4-kapton/ Don’t forget to like, comment and subscribe SB Acoustics RUclips Channel, See you in the next vide...
MICRO-C, Red high gloss, Assembly process
Просмотров 8 тыс.3 года назад
MICRO-C, red high gloss, assembly process Frequency range 68-28000 Hz /-3dB Sensitivity ( 2.83V/1m ) 84.5 dB Nominal impedance 4Ω Max SPL 100 dB Recommended amplifier 25-100W Cross-over frequency 4000 Hz Enclosure type Bass reflex Port tuning frequency 49 Hz For more information please visit : sbacoustics.com/product/micro-c/ Don’t forget to like, comment and subscribe SB Acoustics RUclips Chan...
ARA-Be, Black high gloss, Assembly process
Просмотров 15 тыс.4 года назад
ARA-Be, black high gloss, assembly process Frequency range 45-30000 Hz /-3dB Sensitivity ( 2.83V/1m ) 87 dB Nominal impedance 4Ω Max SPL 105 dB Recommended amplifier 40-150W Cross-over frequency 2300 Hz Enclosure type Bass reflex Port tuning frequency 36.5 Hz For more information please visit: sbacoustics.com/product/ara-be/ Don’t forget to like, comment and subscribe SB Acoustics RUclips Chann...
New SB ACOUSTICS TWEETERS, Dome & Ring Radiator
Просмотров 5 тыс.4 года назад
New SB ACOUSTICS TWEETERS, Dome & Ring Radiator
SB ACOUSTICS, MICRO KITS I speaker product video
Просмотров 4,1 тыс.4 года назад
SB ACOUSTICS, MICRO KITS I speaker product video
SB ACOUSTICS, CERAMIC DRIVERS SERIES I speaker video products
Просмотров 8 тыс.4 года назад
SB ACOUSTICS, CERAMIC DRIVERS SERIES I speaker video products
SB ACOUSTICS TWEETER, SATORI TW29TXN-B I speaker video products
Просмотров 8 тыс.4 года назад
SB ACOUSTICS TWEETER, SATORI TW29TXN-B I speaker video products
How about a new cabinet kit to house two of those.
Very good fullrange❤❤.Can we get this at India??
Bro that low Induction is Amazing, deep Bass, And more Important Clear BASS. :D
Sir contect no please
We believe the SB20FRPC30-8 is unique in many ways. Don't let the low price put you off this fully optimised modern take on a classic full range.
You don't have to record yourself taking a speaker out of a box. Are you going to say something next time?
The midranges have improved so much that they go down ok and go up 2 khz more, no crossover, it's fantastic, that is, top with low consumption..
thank you for your feedback about our driver.
What is your recommended crossover frequency for them? I need to build a crossover for them right?
Yes, you will need a crossover. 2-4kHz although you could go higher. 2.5kHz would be a nice starting point.
Memang joss produk sinar baja baik SB acoustic, fabulous, premier, deluxe, excellent,legacy, dan pegasus semua memiliki kualitas yang mantap
Do you have a max SPL rating for this driver?
Max SPL at 1m is about 111dB. If used high passed as mid/tweeter potentially a lot more.
@@sbacoustics_ That's amazing! and exactly what I was looking for! Thank you for making such awesome products!
Gw bingung barang bagus kaya gini kok malah ga ngetop di negri sendiri ya, gw udh cobain beli yg model murahnya aja asli bagus banget suaranya yg melebihi ekspektasi gw, lewat smua dah speaker2 built up gw yg lainnya
I am waiting for my first Satori MW19P-8. How big volume for one of them in this speaker? In video it say port tuning 32hz. But in text for video it says 39hz. What should i use? 35?
We have checked with the engineers and this speaker is tuned to 32Hz and two woofers share a combined volume of 48.4 litres.
Hi, I have some confusion. On the website of one of your distributors it says: ¨Recommended min cutoff frequency 4400 Hz¨. But the AT60NC-4 datasheet says: * IEC 268-5, high-pass Butterworth, 2600 Hz, 12 dB/oct. I am thinking of using the AT60NC-4 with a cut-off frequency of 3200 Hz with a crossover of 12 dB/oct.
You would have to ask the author of that recommendation to find out why they recommend 4400 Hz. Speculating it may be 2xFs which is common thumb rule when looking at a reasonably low crossover for a dome tweeter. This is not a dome tweeter. The best way to find out is by testing and measuring in your application along with the intended mid/woofer. Look for excessive distortion around the crossover. If it's coming from the tweeter then selecting a higher crossover point or steeper may be warranted. Your suggestion of 3200 12 dB/oct sounds reasonable but it depends on the application.
+ -3,5mm travel 😕 Not sure how should I feel about this. A half decent 10" driver should have at least + -5 or 5,5mm travel, even 8" drivers tend to have that.
How thick is mdf, also is the textreme worth the extra money?
Daddy likes! ❤
Lovely! Would these be useable for open-baffle midrange and treble? I am thinking of a hybrid design (like Qualio’s) with an open baffle mid/treble and a ported cabinet for bass.
Yes absolutely possible to use this in an open baffle design.
Any measurements for these speakers since we can’t buy them at a store and demo them? Thanks
for more information about the spec and features, you can visit this link: sbacoustics.com/product/sasandu/
@@sbacoustics_ I went to the site and there are no measurements at all. We can’t demo the speakers so how are we supposed to know how they sound?
How much price
Please refer to your closest distributor for local pricing information: sbacoustics.com/distributors/
Di indo sendiri ga jual ya? Aneh uga
silahkan kunjungi website kami terlebih dahulu di halaman distributor di link berikut: sbacoustics.com/distributors/ , terimakasih
❤️
Beautiful driver!
I wonder if those high end woofers are better than those in magico or perlisten
Magico doesn't build their drivers, but they have them built per their spec. The Magico M series woofers are based on the Morel UW 1058 or 1258 woofer. The cones are proprietary for Magico, the voice coils are custom wound for Magico, and the spiders are custom for Magico. I don't know about the mids. The tweeters might be Morel TSCT1104 with custom domes. If you search hard enough, you can find where a person took the tweeter apart and found "MBD-5" on the back chamber. Overall, high quality components.
Same as on emotiva speakers?
Cara kami ingin belanja ke distributor sinar baja bagai mana caranya bos?
for SB Acoustics products we have a Distributor in Indonesia, Hwely Audio, for more information please visit this link: www.hwelyaudio.com/sb-acoustics-1/
9 tahun lalu bangun speaker SBAc sistem 2way dengan driver sb17nrx & sb26stac, waktu itu belum ada distributor lokal, dari invoice pengiriman barang dari indo (surabaya), singapore, japan, canada baru kembali masuk ke indo. enclosure box & crossover ngikutin datasheet kit eka, dipompa dengan amplifier LM3886 spek komponen mulai dari dioda penyearah, chipamp sampai kapasitor kopling&elco didatangkan via importir🙈 alhasil jadi orang paling malas didunia sehari2 nikmati lagu keroncong. setahun setelahnya speaker&lifier saya angkut ke rumah orang tua karena pindah tugas. berharap bangun lagi pakai driver satori setelah rumah tinggal selesai dibangun
Hi, I would like to know if I can use the SB16PFCR25-4-COAX in a *sealed* enclosure. Will I have air escaping around the tweeter and woofer's voice coil?
All SB Acoustics coaxial drivers can be used in sealed or vented enclosures. The tweeter/woofer and motor assembly is designed to be used this way.
@@sbacoustics_ Thanks for the info! One more question: Will the "Crossovers for PFC coaxial drivers" from your website work for the new PFCR drivers as well?
So sexy!!!! ❤️❤️❤️❤️🤤🤤🤤🤤🤤 SB y'all make some awesome drivers
Hoping SB Acoustics will make a 12" Woofer with Textreme diaphragm with Neodymium magent. I would like to purchase 8 to start - let me know how. Thanks
Hi, thank you for your feedback, we will consider it for the next development.
Okay let me know. I have prototype loudspeakers built and special circuit to enhance and clarify the bass. I'm using higher-end conventional woofers now but I think your woofers if available in 12in, Texteme and neodymium could improve the audiophile quality sound even further.
Are there any feet?
Hi, do you mean spikes? if yes, we dont use spikes for Sasandu, only flat surface
So just glossy paint directly on floor? I guess I could put a mat under it.
We have been using an ARA-Be set ourselves, truly a fantastic set! Excellent in high and low due to the components used. The TW29BN Tweeter in particular makes a big impression! From now on also available at SoundImports.
⭕ Unfortunately, the company Sinar Baja Electric does not provide an e-mail address for customers abroad on its website. I tried to enter through the form on the website which presents an unexpected error. if the site said which is the e-mail this problem could be circumvented.
We apologize for the inconvenience regarding the features on our website. At this time we make sure everything is going well, you can send your inquiry at info@sinarbajaelectric.com, thank you.
Hi Silvionovais, we have received you message, our team will reply immediately, please kindly wait, thank you
Would love that sb make a replacement tweeter for kef t33 4 ohm 93db/ w...no ferrofluid , to replace all kef tweeters in kef c series, kef 104/2 , 102, 103, reference and 107, there are so many sold and kef does not deliver spareparts...these are exvellent speakers , also the kef P60 , bbc monitor is equiped with this t33 tweeter. And the sb29sdac-c000-4 seems well fitted for specs but need another flange square to adapt in the kef baffle
is the red cable the + ? there is no sign on the tweeter.
very sorry for our late reply, yes the red cable is +
Hadir
Was that starafoame all over the drivers, or What.
we called it dacron or polyester (PET) fiber
I have a question about your measured frequency curves : ALL your drivers / woofers exhibit a huge bump at +/- 40hz. Even the open baffle ones. How’s that even possible ? Do you measure them in a room with a 40hz mode ? Thank you for your answer 🙏🏻
We use a semi anechoic chamber. It's a somewhat smaller version of a full anechoic room. No anechoic room is fully capable of avoiding all modes at the lowest frequencies. Some manufacturers choose to use simulated, blended, nearfield and smoothed graphs in the lower octaves for this reason. Looking at low frequency response in an IEC baffle is nonsensical. That's why we don't tamper with the raw measured response of our setup, it does what it's intended to do from about 2-300Hz and up. For bass response mount in your baffle or enclosure and measure. Or use your preferred simulation method to predict bass response. Any decently engineered woofer will exhibit pistonic behaviour at lower frequencies.
I'm sold! Performance looks phenomenal for the price, heck, even at double the price. Great work SB. Keep it up!
I would love to see larger versions of this driver!
Speaker dynaudio apakah produk sinar baja juga min..?
<3 <3 I see these in my future.
Where can i get this ??? What is the best selling price ??? Iam located in Bangalore
We have a Distributor in India, Eight Audio/Audiofy, for more information please visit this link : audiofy.in/
Is there a crossover design and a cabinet design available?
we apologize for late reply, for now we still don't have a cabinet design that uses this driver. But you can check this link for crossover design uses this driver (PFC/PAC Coaxial Drivers) : sbacoustics.com/wp-content/uploads/2022/07/Crossover-for-PFC-or-PAC-Coaxial-Drivers.pdf
Please help me to see it. SATORI MW13P and sb17cac35 (ceramic) I am confused between these two woofers. The satori is cheaper, probably because of its smaller size. I want a crystal like sound, which unit has the more complete sound?
SB17CAC is a significantly larger midwoofer and has very good bass output capabilities. The Satori MW13P belongs to the top of the range products, but is also a much smaller midwoofer. If you are looking for the best most open and detailed upper midrange I would point to the MW13P. If you need more bass than the MW13P can deliver then the SB17CAC would be a really good choice.
Only £40 each over here in the UK. I'm very tempted to try a pair...
How can I get the kit??
Hi, you can find and contact a our distributor that closest to your location, please visit this link to find the distributor : sbacoustics.com/distributors/
What's the frequency range 450hz to what? It don't give any data
Onderdil dak lengkap
apakah bisa servis speaker. Produk speaker 10 inch neodimium. kendala magnet berkurang suara pelan
Sample suara nya dong...