Видео

Pretty sure that code is related to oil pressure control. It uses a 2 stage oil pressure pump controlled by a solenoid that lives in the oil pump. Isn't the code for oil pressure control circuit stuck off?

Excellent video Brother. Can you talk to me about that lifting contraption? How is powered? What is its max lift height and weight?

I wonder what causes spun bearings? Running low on oil? Mines was full, check with the local mechanic. I had a 2013 Accent I brought used with 160k on it, I was told the bearing spun and it just went down the drain. I should had put a reman motor in it. I drove it on last time on the freeway and it made a loud metallic noise and lost power for about 3 minutes or so and went away. Sold the car already...

Fantastic! Thanks for sharing!

that jawnt slapped redline bro, drop the mods 🙌🏾

Did the same for a rsx

Can you make a video

Tuner or ultra?

Guy: tools make the mechanic Salesman: yes

this is so cool thats why I wanna be a mechanic when I grow up

Connecting rod bearing failure... looks like they need to overbore it and puul the leaves andput new sleaves in assuming the block is worth it.

Piston slap perhaps?

I can respect it. But id like to see 4 more cylinders

So smol🥹

🔥👍🏽

Hd 4 of these because the shifting is superb. Do you know the poor mns big brake kit. Is rotors from a 4 lug mini cooper. Non S. And the calipers and caliper bracket from a prelude or odyseey. Now you can really use the car and its hard to ovwr heat the rotors. And theyre cheap. Good luck. Cheers from wilm de

Fuk YEA!!!!

I've got a K24a2 swapped FG2, I was wondering how you liked the skunk2 intake

What car is that?

👍💯⭐⭐⭐⭐⭐

Whats mods bro

What about scratching the rims. What are your thpughts on that

Vette is a Twin Turbo car

I wish you luck with it - please post if you find a way to get a title - I am looking to do the same thing with an old Whaler if I can get a new title for it - I was able to get one for a 10 ft back in early 80's as a homemade boat when I lived in Hollywood Fl - I am still in south Florida - I think I have that motor in my Mariner manual. clean the carbs - pull the plugs and spray some 2 cycle oil in them to soak while you are cleaning the carbs before you spin the mother - put water to the lower unit before to turn the motor and the water pump might still work OK - I had an 88 115 that still had everything original in it when I did a stupid and let it go about 5 years ago - it need the floor pulled like yours - it was a Del Quay 17 just like a Boston Whaler that I was original owner on - you will need to replace the fuel lines before you put fuel to it - that was the only thing I have to re place twice in 35 years -

Take your bill of sale to Tennessee and register your boat then take your Tennessee registration back to Florida and register it there. You're welcome. :) Only problem is you'll need a Tennessee address :(

😂 My daily is faster than that with my toddlers car seat.

Red is 5mph Faster !

Cool engine, dude

No

Did painting it add Horsepower? 😆 🤣

Tilt trailer ain't rare at least were I am at

1/ $100? Can't go wrong (as long as you don't mind tinkering). 2/ Not sure about florida, but Tx, boats registered with DNR here. Bill of Sale and pencil rubbing from hull number (if available) is all they want (oh, and money). 3/ You didn't say anything about the outboard. Either you got lucky and it just needs rubber replaced or it's a paperweight to avoid dumping money into a headache. 4/ The trailer looks solid. May need some rust attention and for sure new wiring and tires - axle grease and bearing buddies. 5/ Fiberglass repair is gonna be fun. Easy, but time consuming. May want to splash a coat of Durabak (color matching) to the floor and it will look amazing (and have slip resistance). Love me john boats and small center consoles. You can get lots of places others cant. Trailer is an awesome find.

Did you ever get the title to the boat

Great video I just subscribed. Can’t wait to see the next video

Good shit man

That thing looks promising for sure! Did you feel like the bar might damage / scratch up the rim at all when you're getting the tire off?

Some soapy water on the beads will make for smoother dismounts and mounts; looks like you have a money saver there.

Hammer drill FTW when drilling concrete.

take off the tire balancing weight before painting.

Sick maxima ❤❤

It’s like un Saco 😂🤣😂🤣

That looks like bae if I've ever seen it

sdcs

😪 "PromoSM"

Do you have test pipes on here or just stock cats

yoo does this fit a 2006 g35 coupe

That’s stock with just exhaust???