Видео

i own 4 of this and use it every day without problems. You need to verify driver for the mosfets, change it if is possible. Also try to power it without mosfets to see if it consume something and if it consume without mos, problem is driver of mos.

daca lasi acumulatorul de 12 v la o tensiune de maxim 14.4 v nu este nici o problema, il poti lasa oricat. Tensiunea de incarcare admisa de un acumulator ca acesta de 12 v, este: 13,8-14,4v. Daca verifici la masina tot atat ar trebui sa ai cu motorul pornit.

have you solved it? if not, send me a picture with problem

hello, what you mean with `use it on laptop`? as charger? if yes that is because of the battery. To change the current: disconnect any consumer from it, set voltage at 1v, put outputs on short (red and black), set your desired current from cursor, disconnect wires shorted, set voltage desired and connect your laptop or what you use. Now limit of current is set.

salut, nu este de vanzare dar sunt pe aliexpress cam pe la 350 ron si sunt foarte bune

hello and sorry for later answer, can you send some pictures with your mainboard ?

@@unboxelectronics4027 Hello, thank you very much for having the time to respond, I have the photos, where can I send them to you? I tell you that I mount some mosfet of ATX source I managed to turn it on but it does not give voltage and if it demanded current they explode hahahaha ... I would greatly appreciate your support... Best regards

hello, if it burn fuse again you have a problem with power transistors, please verify it to not be shorten

Okay, I'will check what you suggested first. Hehe tanks..

have you solved?

Hello! The fan is not always on. Can be off even if the power supply is on and will start if the temperature will grow up. In other words, there is a sensor that will start the fan on high temperature of the power supply.

if you changed the NTC be sure that have same specifications. Other solution will be to change all system that command the fan with a thermostat or thermocouple ( www.emag.ro/termostat-40-grade-c-contact-normal-inchis-131415/pd/D9292FBBM/?cmpid=86929&gclid=Cj0KCQjw9_mDBhCGARIsAN3PaFNnDpV1gLnPp8ylxK_qpmHqr6EFSMW9nKbnuAijZtoM5Y2y1kIWbfYaApPREALw_wcB )

:)

even i set the - and + i cant control the current it's stop on 0.25 A but i can control the ( V ) there is something wrong

How do you know that current not work?

Hello, from his construction, it will show current only when is in use, not when you want to set it - i know, that i don`t like too.

@@unboxelectronics4027 i thing that's bad model i have one and same problem

To change the current: disconnect any consumer from it, set voltage at 1v, put outputs on short (red and black), set your desired current from cursor, disconnect wires shorted, set voltage desired and connect your output, limit of current is set.

@@unboxelectronics4027 I want to set to 5 ma , I only see 0.000 so it's impossible guessing game

send me pictures, maybe i can help you

because there was not soldered wright, is the first time when i have seen that in this type of power source. Anyway i will recommend this because it look great and is doing his job for the money that you pay for it.

@@unboxelectronics4027ok is it a common fault?? does it cause malfunctions? now i think that i had better remove the cover and check to see if my connections are ok before i use it ,, thanks

@@jamezgee8015 No is not a common fault, like i said before, is first time when i see it, and i have opened many of this type