Видео

How does it compare to the the K3 below it?

I have this same noise in a bass amplifier (Hartke HA3500). Cutting power to the LEDs on the EQ faders eliminates the issue. Very annoying. Why does this happen? It does not appear that the LEDs are modulated. Where is the noise coming from? The LEDs themselves?

RF gain down and volume up is an old SSB technique.

What SW are you using?

This was a very popular radio, it has a nice sound!

Just got my V3 yesterday .. figured out most of it so far; works great on CW .... this is an impressive radio ...

Parting mine out. Never worked from the day I purchased it new from Gigaparts.

So the key switches between RX and TX? Ingenious.

Does it not have sidetone?

I love my ruclips.net/video/Fg9bZTZhkYs/видео.html It has an extra wide SSB-Filter ...73, Ralf

So what is your opinion of it so far? What mode do you operate most? How is cw performance?

Thanks for the demo. I ordered mine today. I am looking forward to getting it and trying it out. I currently have G90 which is also a great little radio. 73 my friend.

Dobriden good manipol. Tanks

Cw is ❤ 73

Great video! I noticed your Omni v.9 has a modified keypad - where did you get the enter, shift and clear keys? Are they from a parted-out Omni vi?

A CW dream machine

I used to have OMNI V with 250, 500 Hz filter installed. I think large Case with Good speaker makes difference in sound. as well as quiet 1st Local Oscilator, AG6JU

So how is it compared to the Elecraft

Great video! You addressed one of my my pet peeves involving recent radios: too much effen' gain! Thanks for showing how to make this rig have a quiet receiver.

Petře, tak jsem se podíval na dostupné informace. Manuál zatím asi není, ale jinak to vypadá opravdu velmi zajímavě. Jaké máš s tím zkušenosti? Můžeš doporučit? Kolik činí poplatky mimo cenu? Zvažuji, že si hoobjednám. Za info předem díky Lev OK2PLL

Petře, docela zajímavý TRX, tedy hlavně provozní možnosti. Ty ho máš? Zajímajímne praktické zkušenosti. Lev OK2PLL

Hi Petr. Thanks for helping me getting my sBitx V2 fixed and hopefully back on the air. 73

Yes the pre gain control effects the NB

Bandwidth ..u can open if u wish ...also what do u have the time set at

Set your rone for around 540

A very nice transceiver, it would be good to hear your comments Petr. 73 Will VK5WB

Hello Speed means too low 73

Would be nice to see and hear you using the key 😏

ok mate how is the cw is the log book working will get mine thursday or friday ..jeff..

If you test it on ch13 which is mid frequency you'll find it will give out about 23w

Good sigs from LZ4408SPA, I love the sound of the RGO One on CW

Nice QSO with K8GL, I really like the RGO One Transceiver.

Nice signs from AD4EB, good QSO.

i use it in my 2nd shack.... with also inrad foofing filter... great receiver! de IK1QHB

On what frequency? There not the same output across the band. I measured my uv25 to 21 watts at 443

Thanks for the video.

Mine has a constant S3 white noise background level even with antenna disconnected, on all bands, running on a battery and tested taking it miles away to remote location. End up having to run it with rf gain reduced to 70% and consciously adding 1 or 2 S points to any signal report. Pity DSP units are so expensive; about half the cost of the G90.

для мене це відео було корисним....... телеграфісти зрозуміють :) лайк!

Had a few tens in my time.. Something a bit different.. Bloody good rigs

What is the receive like though?

Absolutely will give this a go, thanks. Similar results with SSB?

220 volt?

No joke. I use mine mobile, and it’s worthless until the RF gain is set below 20.

Does this problem still occur once the ATU has found resonance and has been deselected as per the instructions in the handbook?

My uv-25d puts out anywhere from 21 to 26 ish Depending on UHF and VHF

These are such cool rigs. Great features, very thoughtful design, not overkill on watt output, but above QRP, and remote face, with common vga cord, sortof. I wonder what the grand total G90 units sold have been since around 2018? debut, both editions of firmware...

It is very confusing that on bands with propogation, you struggle to make fringe contacts, that fade in and out and are going to get your ear blasted by someone on short skip trying to get a contact also, or not even aware, when there is steady groundwave-0 propagation bands to test direct range, at anytime of day. With 0 propogations, there will be 0 stations on any band in hf but 10 meters. It is like holding eyecontact with people on the other side of a resturaunt, when you are at a table with people in com range. Do what you enjoy, but it seems nerveracking.

No squelch. 😔

This video helped me. Ignore the haters.

Cheeeeesh! We've been reducing RF Gain on receivers since the 1930's. This is like rediscovering the wheel. You simply reduce the gain to below the noise level. The problem is that each band has a different noise threshold which becomes a lot of trouble when band hopping. This same setting on 10 meters will make the receiver deaf. Thus this is why we have AGC or automatic gain control. With AGC we can leave the RF gain at maximum and strong signals won't overload us however the tradeoff is having to listen to receiver background noise. Pick your poison.