![Boiler and Plumbing tips made easy by Johnny Walker](/img/default-banner.jpg)
- Видео 40
- Просмотров 146 249
Boiler and Plumbing tips made easy by Johnny Walker
Добавлен 23 фев 2019
Helping apprentices and GASSAFE Engineers in the Trade , DO NOT ATTEMPT TO WORK ON ANY GAS APPLIANCE UNLESS YOU ARE ON THE GAS SAFE REGISTER & COMPETENT TO CARRY OUT THE WORK
Видео
Johnny Walkers Disclaimer
Просмотров 1515 лет назад
This video is about My disclaimer... Don't forget to subscribe!
Glowworm CXI blocked plate HEX and low water pressure switch
Просмотров 4,6 тыс.5 лет назад
Replacing DHW HEX
Removing electrodes and burner on Worcester greenstar
Просмотров 16 тыс.5 лет назад
Removing electrodes and burner on Worcester greenstar
How to change prv and expansion vessel
Просмотров 10 тыс.5 лет назад
How to change prv and expansion vessel
Baxi 105 pump change and pressure gauge
Просмотров 8 тыс.5 лет назад
Baxi 105 pump change and pressure gauge
So what was the gas rate ?
Lend us A ciggy
Central heating is working but no hot water: The 'actuator control' situated at lower left hand side (black plastic unit, with black thick wire and quick release connector ) Pull out the clip at its base: the actuator will pop off. Buy a replacement unit from "central heating spares" for £ 49.50. Pop back on; fit new retainer clip, and wiring socket. And ha presto! This information is for Potterton baxi 25, but it also applies to lots of other C/H units. (no need to switch off water , but doswitch off boiler before doing job) good luck!
Sir! thank you!
I have this one and intermittently it makes a very violent vibration. British Gas have changed the fan to no avail.
I've always said that the biggest con with modern boilers is the cost of a new pcb board , just because a couple of components have failed on it that cost very little , that's why I will always give my customers the option of a reconditioned board that is a quarter the price of a new one and you still get a 12 month guarantee the same as a new one from the company I use... 👍
Yeah the pump housing. Undo those two screws. All well and good until you come across one where that bottom screw is completely chewed making it impossible to get it out 🤪 whole manifold change then
I’ve got a fault with the 30+50 degrees is flashing. Do you reckon it’ll be the PCB ?
I've got a ideal icos he12 boiler, my heating and radiators come on fine but I've got no hot water coming out of my taps. Do you know what could be causing this or any solution?
watching you use a drill to undo two 5mm long screws is agonising. so many screwheads fucked and now i know why
I’ve a Worcester Bosch 24 28 system - & flush heat cell / plate as per link below. I’ve to change pcb on the model your showing here - was just having a brief look to see how to flush/clean. Besides the glow worm method of pouring water into the heat exchanger after removing (doesnt make senseI wondered whether you could introduce Fernox F3 to clean. Or with glow worms you don’t use chemicals? Ta Worcester Bosch junior 24 28 ruclips.net/video/JAVLi3-YcQ4/видео.html Glow worm ruclips.net/video/d7qJNEjX01I/видео.html
Guys, I've decided to change/clean that paddle. Do I need to turn off the main water supply tap and also drain water from boiler/radiators first?
Thanks for the video, you were 100% bang on and just saved me over £150, I had a old psb and removed the part (relay) and replaced the one on my psb, worked straight away, thanks again.
Better with a new boiler
Boss man job really helpful video
You are boss man really helpful video
Does the water need to be drained first
Thanks for sharing good video
I've just changed the electrodes on this boiler. The new set seemed to have quite a gap between spark electrodes. Can this be cause of loud ignition? It only started happening after i changed the gasket and the electrodes
Thank you for sharing x
Yep, motor was fine but seal was stuck to the CH port on mine. Cheers mate.
My ideal icos shows H1 fault theres nobody on youtube talking about that fault code.any idea
Thankyou so much for this. Such a simple job. A local company quoted £200 +vat to fit my supplied part. I brought a reconditioned one, off of the net, and fitted in less than an hour. The longest was clearing the worktop. This was on the water side, and not combustion side, so I felt confident for this repair.
Top man
Dust sheet to protect customers work top would be nice. Great video
Bang on 👏👏
This video gave me the confidence to try fix my mums toilet. It went perfectly. Cheers! 👍
Great video
One of reasons WB are shit boilers, can change most other expansion vessels in 20 minutes , 10 minutes for prv
What pump change lol. Tadaaaahhhh ffs
Thax God bless
Cheers, mate!
Why does the fan have come out???
The two things that everyone on here are talking about which is not my problem. Its taken numerous engineers and years to get it sorted, its low gas pressure at peak time we can not get hot water due to low gas pressure, too many people using the gas!!
the heading says ...diverter valve change ......people are expecting a video showing the changing of the valve .........didnt happen .....shit video
theres maybe 2 videos which precede/follow this one which he goes into depth on how to go about it. Not everyone has great editing skills or the means to splice different videos together. Shit comment.
@dannytennyson3688 well said mate
Hi mate just found your channel, really helpful. I’m just starting out as a trainee gas engineer. Quick question regarding the potterton promax system heat only boiler How did you get it into service mode? Do you just call for heat with room thermostat? And does it go straight to maximum output? Thanks
GREAT VIDEO well explained but wondering why you didn't just replace original part number PCB, as you appear to have used a different PCB?
Also known as watering cans.
Nice car
how much does something like that cost ?
Good vids mate been helpful👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻
Unbelievable,this is how to change a pump he says,shows us it repaired,and the old parts,but not how to do it!!!!fucking weird
How to check ignition electrode and flame sensing electrode and boiler spark generator using multimeter?
I have both o rings on the adaptor and o ring on copper end but still get a drip
Hello. Does the sensor have o rings inside in each side?
my baxi 105e stopped today, no water or heating and no error neons have lit up no flame either or ignition noise, the green On Neon is on. i have noticed that all neons will dimly flash red when i try and reset, any ideas
I have a Worcester Bosch Greenstar 30i that loses pressures after the heating as been on. I've pressed the schrader valve on the expansion vessel and water comes out. I haven't noticed the the pressure gauge going over 2 bar or leaking outside. Can i drain out the boiler by turning off the flow and return valves then pulling on the red lever of the PRV to drain off outside to replace the vessel ?
leads on ignitor wrong way round does this matter
Nobody ever died of tetanus, just more fear to it.
A dickhead desisgn especially when these watering cans are located in waiting cupboards.