Видео

Stanton Streets

Help got the bobbin working again but it’s fraying the top thread. Is my hook too close to the needle.

my needle threader worked great untill i changed my needles now none of them work what did i do

ESPAÑA

If you're having trouble getting the cover off or back on, go to the side with no screws, if you have a flashlight you'll see that when you flex it out a little bit, there's a little black peg holding it in place. you'll need to flex the plastic just enough for the black peg to come out of the hole, and the same goes with putting the cover back on. Also look at the backside of the cover when you take it off because there's a lot of lint that can build up in there as well

I get a question mark, why?

Don’t need music please.

comme régler le crochet en français

If you are still monitoring this video, please tell me what the tool you use to take the screws out is called. A link to where I can purchase it would be awesome! That just looks so much easier! I can't find a tool like that. And thanks for the video!

Very well done video, thanks for sharing your knowledge.

If you see this March 24,2024 can you share what this message is and how to fix it. (Main Motor encoder signal error) Thank you

thank you exactly what I needed!!!!

Show

This video is not good. There’s a few steps in the disassembly process that are left out and that makes the reassembly confusing. There’s a space under the copper screw and rides on top of the shim. This video doesn’t show that.

Здравствуйте. Помогите пожалуйста. Не режут ножи. Купили новые, все равно не режут. Что делать? Есть какая то настройка ножей. Заранее благодарю!

Thank you very much, very clear.

Hi i have a question, after i finished embroidering, my machine cuts the thread and the thread shoots back up and i have to reinsert the thread into my needle etc. Why is that happening?

Hi, i replaced my knifes with new ones, and installed everything as usual and the washer. But the Knifes wont cut correctly, or the threads are way too long. Can you help? Ive checked everything with the service manual but cant figure out. Maybe the picker isnt out of place?

Hi, thank you for this video. Do you have a video on how to correct the X & Y axis ?

what is the locking position on the spindle when you put this bobbin case holder back?

What three buttons, they do not show on the screen!

Thank you so much! This was a lifesafer!

Ciao! Che file supporta?

I have damaged the thin washer underneath the cutter as shown in the video. Would you be able to tell me the name/part number?

Excepcional

Thank you for this video. It’s been a while since I used my machine and I removed the wrong screw. when I tightened it back done a piece moved and I continually got wiper error. I was able to fix the position after watching your video.

Well done sir

How much price?where is ur adress?

I'm not understanding why you would need to remove the cover on the tubular arm... unless its to just look for debris. ??

Omg that's gonna save me a trip to the repair guy thanku 😊x

Is this all they do when you bring a machine in for yearly service?

Thank you very much!

A few problems with this video. The machine is jammed. If the hook-race are jammed you cannot turn the handwheel to access screws. The machine is jammed. Secondly you should not ever use pliers to yorque the hook. This is not Stock sewing quality guys.

This would be the best video on this job if it just ran slower and he spoke the words and left out the music!

Thank you so much! Fixed it with your assistance. One question, though. Why does the cover on the left side have to be removed as well? I just opened the right side and took care of business than capped her back up.

Thanks So Much!!! Broke a needle inside the hook, it was stuck and followed your instructions after getting it out and my machine is perfect!! It also thought me how to deep clean and oil the entire thing!!! Brother PR1000

Are you supposed to hit ok after reaching 199? Bc when i started spinning the hand wheel the motor angle started going up. So I brought it back to 199 & pressed OK, it told me inappropriate needle position, and it put the needle back in place. Now with the spacing.... what should the # be for hook position & the # for spacing? On your screen it said 3 for the hook position & 4 for the spacing position. Are they the correct numbers?

Thank you. This is a great video! What type of oil should I use?

Kam karne ke liye sar

Job mil sakti hai

Once you have things set at 199 do you press complete or just put everything back together

Saved my life, thank you so much!

didn't work for me on PR1055X - it doesn't have the part you move - oh well

Hi I've got a brother pr1050x and you helped me to replace the needle threader last year. Can you help me with your great instructions. to replace the presser foot XC5685151. Thanks

On my old PR600 i needed to press ALL THREE console buttons on start-up, and then the above worked perfectly.

does this work on a Pr600?

Missed a step…. Guess I will go back to Renee’s video…. I had hopes because it was shorter and more concise…

THANK YOU SO MUCH FOR THIS INFORMATIVE VIDEO!!!!

What is the purpose of removing the central screw from the neck of the machine?

I have done exactly everything in this video and now my machine won’t pick up bobbin thread. What can I be doing wrong?