Видео

So what if it isn’t the fuse?

Informative video but I do have a question. I’m looking to do this on my older 5.7L and I’ve read that this generation HEMI doesn’t fully drain the engine of its coolant without opening the drain bolts on both sides of the engine block as well. Additionally, even then, I’ve heard that all the coolant / water doesn’t drain so I’ve ready advice that is against using the pre-diluted coolant because the water still present in the system will not allow the 50/50 mix to be correct.

why tf did do we have the same fucking shift knob lmaoo no way the same black one lmaoo XDDDDDDDD

Great vid 👏🏻

Can a bad water pump/ faulty water pump cause engine to overheat when turning on AC?

I have trouble removing the pulley. The threads don't in as if it doesn't have any threads

Awesome! This is the issue I was having. After your video, I replaced the Blower Motor and resistor! The AC now runs perfectly! Thanks a million!!

The shop quoted me $2,200 for front and rears.... I think I'll just do it myself. Thanks for the video!

Thank you sir. I just bought the same EGR. Did you have to use any special Mitsubishi software to initialize new EGR? Or just install clear codes and thats it?

Thank you for the video, 🇲🇽

I'm going through this right now, replaced the sensor and am still getting the code. I wonder if I replaced the wrong one, as mine is the side mounted sensor. Thanks for the info

Thank you for posting this video! I had a squealing noise for months thinking my AC Compressor was going bad. Sure enough i noticed my balancer was missing the entire center piece. I slapped a new one on and all the squealing is gone.. 😁🙏🏾 FYI I used the factory bolt to press the new balancer on, used a 1/4 extension thru one of the openings to keep the engine from rotating. Torqued to 130 ft-lbs

What were the symptoms ?

Tks

Nice

The overdrive work

Thanks

Thanks! One thing: open the brake oil reservoir and monitor if it is not over the limit when you push back the caliper.

Where did you order the pulley from

Oh yeah, spent $30 just to get a free bucket worst advertising ever 😅😂

That's an IAT sensor mate not a MAF sensor. It measures intake air temp, not air flow.

This is a heck of a job. Thanks for posting this!

do they sell T-rex shirts and are they on sale

Damn. 😔

After changing my cv axle, the caliper seizes. I changed the caliper, brake hose and master cylinder. It still locks up when driving.

Just found myself in the opposite situation after watching this video. The pzev that has the bank 1 sensor 1 from the top is the Denso 234-9049 but the ulev version which has the sensor from the side is the Denso 234-9010. My mechanic was getting impatient with me after I made him switch it again lol. Thanks for the vid.

Start a jar. Every time say uhhh or ummm put $20 into it. If you can’t put cash in, do 20 pushups for every dollar that you’re short. It doesn’t take long before you will improve the efficiency and effectiveness of your communication and elevate the professionalism

Great video but I have a question. I’m not doing a full coolant flush but I need to add some coolant. Can I just match the color of the coolant when I add it? It looks to be a light pink color like in your video.

Got this done for 140 today thought I blew a head gasket! 🙏🏽

Buy two. Grind off the 1/4 anvil for tight spaces and grind off the 3/8 anvil on the second one.

how often do you do this for cars that dont see that many miles? (weekend warrior cars) ?

Poor review and Poor video.

Where did you put the Cata clean?

great Job! Thanks for the education, you are a careful, thoughtful and skilled engineer.

love it! I only do DIY and light automotive work on our own vehicles so nothing major, even having the HF proper tool makes a world of difference though.

I have seen other videos and comments where people have said that actual toyota techs don't use those types of filter wrenches as they will crack the plastic filter housing. They often just use a 64mm 14 flats oil filter wrench.

Awesome thank you!

Great video man, does anyone understand the aftermarket options of different percentages overdrives like 15% over, 25% over? What does that mean. I figured since I’ll replace I’ll upgrade it to stronger than factory.

This just happened to me today in Australia with my 300 SRT 6.4L, I was like WTF! 🫨

What if I don’t have a lift?

Would you remove the windshield wiper parts and cowl pan again?

Did it actually level it out I'm in process doing mine and the spring is a bi@ch

You didn’t say what kind of oil you used synthetic or conventional. Is it a high mileage vehicle?

😑 Customer sounds like a dweeb.... you don't change struts side at a time... you change them in pairs!

What tool is that called?

You are also the only one that covered the belts and pulleys to limit the amount of coolant all over the belts and pulleys! Good job Man! This shows you care about your work and your customers! I'm an retired Auto tech so you got this!👍👍

Hey, good video, I have watched 4 videos on this subject and you are the first to clamp the upper hose! Respect!👍👍👍

Very informative thanks sir

You make very nice videos.

Hey dear steven. how are you? I saw your RUclips channel. You make very nice videos. But do you know why your video is not going viral even that.