- Видео 18
- Просмотров 108 544
Rattle Trap Garage
Добавлен 29 авг 2018
Here to give you tips and tricks and buildstuff
how to adjust you're choke and idle screws on a divorced choke q-jet carburetor
how to adjust you're choke and idle screws on a divorced choke q-jet carburetor
Просмотров: 56 774
😩
Sounds great And all but I wouldn’t be taking corners like that at that speed with a truck 😂
@gypsynikkomitchell3077 yea probably not one of my smarter choices
@@RattleTrapGarageyea but…truck sounded awesome lol
@@gypsynikkomitchell3077 worth it 👌
@gypsynikkomitchell3077 I just put a new engine In it, should I make a walk around video of the truck?
@@RattleTrapGarage yeah that’d be cool
10/10 video
@stpatrjck9665 thanks, I know i need to make more videos
Get the dealer tune up manuals. Like SD-100. Very specific procedures for setting everything. All the different carb numbers were adjusted differently too, even points were set at different specs. My 1972 factory 300 h.p. 350 is 4 turns on the fuel air screws, initially. According to that gm book, they ranged from 175 h.p to 375, for the 350. The later gm tune up books used exhaust sniffers to adjust, for NOX.
@davidpotter7484 this is really good information, I really appreciate it man best of luck to you, I over the past year experimenting with different jets and what not have noticed the choke likes different adjustments depending on jets and metering rods aswell as mixture screws, lots of things I wished I mentioned in this video
@RattleTrapGarage nothing is arbitrary on a factory set up, very specific settings. Extremely easy to just follow directions. Then, they start, run and drive just like new with the best mpg, if driven properly. I had major issues with vacuum lines for years, until i found places that still made them. Parts store vacuum lines will cause leaks as soon as they get hot.
What a jewel you have. Nice
Thanks
You just solved my issue. Thanks.
Glad I was able to help 👍
We just put a correct intake on and the child mounting surface is not there. We made a stainless plate to go from the two available bolts and mounted the choke via an aluminum sleeve in the middle of the plate. Seems to me that the heat is not going to transfer well to the underside of the choke body. Guess we are back to the drawing board unless you have a known solution??
So upon cold start butterfly has to be closed?
Engine cold 1 pump choke closed starts up automatically opens a smidge
My 75 Chevy k10 has a carb just like this although its branded Edelbrock. Anyways it idles pretty high cold and the choke won't kick off until after the temp gauge is about halfway up. I can goose the gas to cut the choke off but as soon as i drive off again the choke is back on and the engine idles high. It takes forever for it to be warm enough not to do that. What would I adjust in this case? Sometimes I hit the gas and the choke won't open up. Like it sticking or something.
Yea there's that high idle screw between the choke pull off and carb itself you can lower the cold idle speed there, if you want to adjust the amount of time the choke is on you can Slightly bent that other rod going to the choke thermostat
That sound brings back some memories
Square body
Yessir
Nice
Thanks for info. You explained exactly what problem I'm fighting. Now to bend rod and check vacuum module.
Good luck hopefully everything works out for you
You can also adjust it to open a little less I found that works better for smaller jets
Can you get a quadrajet carburetor turn right for a street cam engine
Since this video I have built a little built engine flat top pistons 487 heads with a larger cam and the quaderajet still runs Phenomenal the only thing I had to change was jetting and the power piston spring starts awesome gets around great cruises like you wouldn't believe, but yea you should be able to iv seen them on some pretty built engines they seem to work
289?
Tree fidy
So I’m having a problem where my car will start and warm up at a very high idle and it won’t go down give it a blip of gas and it will sit at the revved rpm for a while until it returns back to the high idle
I'd check the throttle cable and throttle linkage and shoot some oil at it also behind the choke pull off vacuum canister there is a screw to adjust high idle
Thanks
🫡
They don’t make em like they used too..
Very Cool
I had rebuilt a 305, put in a torque cam, rebuilt and tuned the POS Quadrajet 4bbl in an 84 Z28. It would start just like that. Just touch the key.
Mine has a quaderajet it runs amazing
The temperature gauge reads like it’s been started for a little bit… still impressive
Indeed It was a warm start
I don’t think the starter gear even made a full rotation 😂
It's fast this was when warm cranks a rotation when it's cold lol
...sexy...
6.2 for evar!
I have a buddy with a 6.2 in his 83 this just has a 350 chevy
Me likey😅
The other day we had 10°f, so to me that is not a cold start. Last winter it got down to -32°f! That is a cold start, even with a block heater! Because the oil in the pan is -32°f!
Starts the same in -5
That dash is sick
I thought it failed. Quiet as hell.
Yea it has stock single exhaust not very loud
That buzzer brings back memories..
It didn't used to work but I like having everything functional so I got one for it
@@RattleTrapGarage it diffenitly works now lol...
Sure does 👍
shes screamin!
Sure is
I lose power going up hills. It used to drop down to 20mph. I adjusted the kickdown and now it will sit about 40. Does this issue have to do w the carb? There’s only hills around me in higher elevation so I’m thinking it could be that. It’s a k1500 that runs a little rich.
It could be a lot of things have you checked timing?
Hell yeah dude💪
Nice 💯
🏁🏁🏁
Is that a 78 ?
Yea with 77 silverado interior
Cruising down the street in my '64 😎
Sounds great.
That's when cars were great they ran on vacuum and hydraulic pressure no computers no sensors no stupid b******* that are on cars now old cars are better than and they were made with steel not plastic you the timing chain that didn't wear not a timing belt that breaks and you have to replace every 7 years old cars had more room in the engine compartment so you can new cars suck
I agree
You should probably put an air filter on it
I did just removed it to film this
@@RattleTrapGarageI figured, I'm just talking shit
I figured lol
A liberal checking out his next stolen vehicle……
😱
Is it a 350? What type of exhaust? I have an 88 Suburban I want to sound like that!
It's a 350 with 487 heads ported out with over sized valves, flat top pistons and I think the cam is 2 stages bigger than a rv cam, the exhaust is stock but without a tailpipe
Bubba thank you for the content. I'm working on a divorce choke for first time and couldn't figure why it's locking up with a closed choke. After it warms up I turned off the truck and hit the gas and my choke closed tight and the truck wouldn't start again. Your saying bend the rod so it will release the choke with vacuum.
Yes
THANK YOU SIR!
Np
Good video and a cool looking square body 👍
Thanks
What does "bog" mean?
It'll cut out repeatedly and have no power under acceleration
One of your lifters is gone
Loose rocker I fixed it
@@RattleTrapGarage Why does this happen? I just picked up a 1980 corvette all original, it sounds exacly like a have a loose rocker too, but when it is warm and does idle and runs smooth, im just waiting on new cover seal to arrive to tackle this issue
@rolexshine923 mine actually ended up being a wiped cam lobe but it could be a lifter losing its prime were it will clatter on cold starts and pump up as oil pressure builds and the sound goes away
can you clarify your idle mixture settings - you said they are turned OUT 3 full turns? does that mean you completely close them by turning them clockwise all the way, THEN three separate 360 degree turns counterclockwise from that fully closed position? thanks
I turn them all the way in then back them out 3 turns
And yes 3 full turns
Also 2 and 1/2 turns work too
Hey buddy. My 83 cutlass starts up great when cold after pumping the gas 5-7 times. Drives smooth with zero issues but after shutting it of to go inside a store, it doesn’t want to start. I have to take the air cleaner off and hold the choke open with a rag while I turn the key and starts up. Why does the choke close so fast? Is my electric choke bad or something needs adjusting?
So it sounds like the choke might not be opening enough and when it sets it closes and won't start cause its flooding its self when the choke closes, i think it could be a bad electric choke element or the choke pull off could be bad, the vacuum canister on the right side of the carburetor. Try pulling the air cleaner and watch it when you start it and see if it pulls open when it starts
Also I have an 800 cfm with an electronic choke I might do a video on soon
Thank you and I will take a video of it. After watching your video, I only pumped it once like you say and it starts great. I don’t know where I got the idea to pump it so many times but thank you for the great video.
@@montrose5paulina you're very welcome
Hi great video! The vacuum port sticking out next to the mechanical choke what is it for? I'm not sure if I should cap mine off?
It's for the heat riser on the a factory air cleaner it's not that important
@@RattleTrapGarage That's the Vacuum advance port on my 69 427. I'd cap it if not in use.