Видео

Something you may be able to answer for me that I struggle with understanding. The excess grip tape is twisted into a little tail and tucked into the shaft. Does this keep solvent from getting into the shaft? most of the solvent that you put on the tape is squeegeed off during installation and most of the solvent inside the grip is pushed to the back of the grip and comes out the hole. At least that’s what I’m seeing. I’m guessing that you’re not supposed to get any solvent in the shaft which could possibly cause rust if it’s a steel shaft. Once the grip is on and everything is dry should you take some sort of ice pick or some thing and poke a hole through the grip tape at the end of the shaft so that air can come and go inside the shaft as necessary to prevent condensation or something like that?

A lot of comments on how he never removed the grip-side tape backer and my guess is it's because it's not necessary to do so. There are many videos showing club re-gripping using just ordinary masking tape and compressed air from an inflator or small compressor. They use an inflator nozzle pushed into the drain hole on the end of the grip and the air pressure expands the grip enough to easily slide it on. No solvent, no mess and much easier to remove or reposition if necessary. Apparently the grip doesn't need a sticky tape surface to stay in place and he may use grip tape instead of regular masking tape to ensure the proper amount of buildup because regular masking tape is much thinner and requires multiple layers for the same thickness. Steve maybe doesn't know about using air or maybe just prefers solvent but it would've been nice if he clarified the how and why of his method.

what type of torch do you have

Can you use hairspray like the bicycle industry uses for bicycle grips?

Hello thank you so much Firstntime doing this So the double tape comes with white paper on one side and yellow in the other side. I pulled the white out and left the yellow paper Then i left the However when i put the solvent and tríed to fit it in, it would get stuck after I inserted the first inch And the grip was bending in all directions However not going in

If you use a utility knife, just roll the bottom of the grip back a little and cut through the roll.....no big deal.

Also there must be something to those curved blades to cut grips off. You are the 2nd person on here to do so. I've always used the traditional normal flat blades. 10 yrs experience. Thanks. Cheap fix.

Learned something new. The finger on the underside of the grip for solvent. Hobby club builder. Thanks

Good video but aren`t you supposed to remove the tape backer?

Thank you

Can you use WD-40 for grip solvent?

Only cautions I can add, being elderly. is DO NOT use nitrile gloves. I thought to protect my dainty fingers, and could NOT grip the grip - it went on half way then I could go no farther - had to cut it and throw it away. For my next attempt I used a "gripper glove" on my forward hand, and had to be careful not to stretch it; otherwise, it worked - You need a bare hand, or nitrile glove 'cuz you have to block the hole with your RIGHT, then you are only pushing with it

Thank you!

Now if I could only find some grips at reasonable prices!

Thank- you!

Pro Tips Steve, Bravo! Too many DIY videos on not telling the full story. Hook Blade is definitely better and way safer/smarter. Amazon: "golf regripping tools" for the basics. General rule of thumb: once you apply 3 wraps, you move up a grip size from Standard to Mid-size or Midsize to Oversize

stupid question: why didn't you have to peel away the backing on the tape?

Does the 1/4” of tape overlap on the underside not matter? Part of me considers trimming that 1/4” of width off of all my tapes so that there’s no overlap

mineral spirit gets glue residue off quickly

Are you not peeling off the top layer of the tape at all?

Got the grips Just waiting for my grip tape to arrive to redo all my Irons, off to buy hook blades tomorrow

WHY shouldn't acetone, vinegar or acetone be used?

If I'm changing a grip on a brand new club ..can I keep the pre existing tape on ?

Video starts at 4:50

Thank you!!!!! torch saved my a$$

Thank you for the tips

I never saw him remove the backing paper from the grip tape. It is supposed to come off, isn't it?

First time I've regripped graphite clubs and it was definitely easier thanks to your tips, so thank you!

Ordered grips and tape, but didn't know it was solvent activated. Thank you for showing an alternative. (mineral spirits)

Thanks for the video. You say not to use acetone, but do not explain why. Other vids/articles say acetone is fine alternative, as is WD40 or even soapy water, which just takes longer to dry. Hmm... a little confused.

Is The grip tape your using double sided? If so don't you have to peal off the non stick side before adding the solvent?

Your video is the most informative and interesting one and I want to thank you. You just saved me a lot of money.

THERE IS ONE THING I WAS HOPING YOU CAN HELP ME WITH. MY WIFE HAS A 51 DEGREE D CLUB BY LYNX. THE SHAFT FLARES OUT AT THE BUTT END. I CAN'T SEE HOW TO PUT A GRIP ON IT?!

When using double sided tape do you take off the top layer of the tape off or do you leave it on? When I regrip a club I take off the top layer and after putting on the mineral sprites it is real hard to push on the grip. Will the grip stay in place with the top layer still on? Jerry G

Nice video!! Thanks for sharing! I would like to setup a simple workbench like this in my garage one day not only to do regripping of clubs but other projects as well. This could also be a nice side job to do from home as well.

For steel shafts use a glue gun to remove tape then heat up the remaining glue and brush on white spirit while it's still hot, it will come off easy. Be advised to wear gloves to avoid burning your hand. Easy. Clean out the ends with a small screw type toilet brush and WD40 if you want to do a proper job.

You forgot one piece of advice. "DON'T SMOKE WHILE YOU POUR MINERAL SPIRITS ALL OVER YOUR FLOOR".

great video

Is it the same process for steel shafts? As far as removing the tape?

How does the grip aline with the head?

little more solvent...slam down bottle...more solvent...slam down bottle...just a little more...slam down bottle...a little more...slam down bottle...slam down bottle again ...you're done 😂

On the double sided tape I take off the other side of the tape to.Way wouldn’t you?I’ve did it my way for years without any problem.

After the grip has been put onto the shaft, compare the length against another grip to ensure that the grip has not been stretched.

The wide double-sided tape. You have the join or overlap at the top, I would like this join at the bottom so I would face the club tow down and then move it 180 degrees to line up the grip when you put this one. I expec you will say that the join should be at the top?

Terrific tips. Thank you. Glad to know I can use mineral spirits in a pinch.

It’s not garbage if it works better then it’s supposed to 🤣

big help with the hook blade, and heating the tape not sure why you didnt take the backing off the tape but still a big help!

Perhaps I’m overreacting, but is there a safety issue with a naked flame near a can of acetone? Ok, it’s sealed by the looks of it, but perhaps place it in another place well away just in case.

17 mins is just too long. The first 30 seconds your repeating the title of the video which is uneccesary. I would really try to condense your content, it will really help you.

Is it OK to use mineral spirits without gloves?