Видео

Hi sir, thanks for the video, please make a video of static transfer switch using thyristors.

Vary good sir. Possible contact number

This channel is the best 🎉🎉😊

Very nice video 🎉🎉😊

Awesome channel we need more videos 😭😭😭😭😔

We need to come back 😭😔 Awesome channel 💯💯 thanks for everything 🎉🎉

❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤ 🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩🇧🇩

where did you get that Teseract at the end of the video?

Brother! what is Thiasotiks?

❤❤❤

It's very helpful.... ❤

Nice project sir..... thanks for sharing ❤

Hi, Can this circuit be used for mains voltages, say 240V ac mains input fuse replacement.

Thank you for the video. I tried to rebluid this experience with P-mosfet , but I get always 12v in outpout of buck, because the gat p mosfet is always open in this configuration. please can you explain and tell me what i have to do to siolve this problem.

Love your efforts made on this reverse engineering ❤❤❤

Will you be adding feedback to stabilize output voltage

Is code are complete for charging and changeover function

Very nice work. I have a question. To convert a square weave inverter in to sine wave inverter , only changing firmware is sufficient or we have to change transformer also.

vc e muito bom na programação vc conseguiria fazer SPLL para sincronismos de inversor com rede elétrica

Looking forward for more informative tutorials. Regards 🙏

Nice watching your video would help me learn a lot. Regards 🙏

thanks

Good to know you are also fan Sam Benyaakov's fan. He is THE BEST! I am guessing the gate driver is getting burnt because of long wires on the perf board. Schematic wise I didn't find anything wrong. However, C26 for Bootstrapping looks quite overkill and also little more capacitance at the VCC pin (Parallel to the C27) would be nicer. Diagnostic of a circuit on perf board is quite difficult task as you can't take all the parasitic in account. Only part that I didn't like is the steering of the voltage loop via PWM DAC and D4. I would use a summing amp instead. Another problem with synchronous buck in this plan is when duty cycle is low and its running in DCM. The LO side MOSFET will discharge the battery instead of charging.

ADC reading equivalent to maximum chg current during full charge = ((ic * a) / ADC res); For example. ic = 0.5 A, actual voltage amplification. a = 0.22, ADC resolution = 4.887 mV, please explain where these numbers come from.

Hello, may I ask? In the diagram, pin D3 in the arduino is specifically the +VE_CY pin. If I don't use this pin, will it affect the operation of the circuit? And the next question I want to ask is how to measure the charging current of the battery, when the shunt resistor has been used to measure the overload. I do not use the CHNG-OVG-RLY pin, but only the CHG-RLY pin (relay switching between inverter and grid). Is that possible, sir?

YOU REALLY STUDIED AVR CHIPS. THIS IS FACTUAL!

Excuse me sir I want to modify it with a 4 wire fan, can I modify the program for example the fan speed depends on the temperature reading of the lm35 with the pwm output which controls the fan and there are remaining atmega pins there are D0 or TX can I add a fan rotation failure feature by reading the tachometer pin on the fan 4 cables, whether the atmega memory is not remaining or the sine pwm generation function will be disrupted

hello, i'm has read your code for this vidio, in your code the lookup table make with matlab, how to make the lookup tabel with matlab ? can you help me sir ? thanks

could u please do bldc motor driver based on arduino? there are alots on utube ,but they are speed fast by varible resistor ,also they could not explain what the best signal for bldc motor ,is it spwm what u use it in the inverter or the six steps bldc signals esc drivere that on the market?

hello, can you share circiut diagram

দাদা এটার .ino file হবে???

Thank you. That was interesting and informative

Hello sir, Hope you're doing well, i have a POWEDRIVE 3000W Inverter that makes only about 80 wats or so, if i plug anything over then that it overloads and beeps Any idea what could be the issue?

I don't know a lot about electronics but I do know about this guy. He is a pure gem 💎. Keep on going Dadabhai ❤

Excellent .

In this inverter feedback

if i load ICR1 with value 63 can i get a pwm frequency of 250000Hz without prescaler. i used your equation. thanks

স্যার আমি আপনার সাথে যোগাযোগ করতে চাই, দয়া করে আপনার সাথে যোগাযোগের কোনো একটা মাধ্যম দিন। আপনাকে খুব দরকার।

I week English language but My quation are atmega16au ic charging feature and feedback featcher working this oc

How many mhz use crystal?

@ 5:05 pm you are telling you are connecting resistance || to R2 it is wrong you , it should be || to R1

❤❤❤❤ awesome 😎👍👍

❤❤❤❤ awesome 😎💯👍👍

Hi sir I'm struggling to make feedback to an op-amp based inverter (no microcontroller...just analogue). Can you do a video on feedback control for this ?

Well done sir!! The breakdown of the circuit is impressive 👌

Hi i looked at diagram. I made inverter from op-amps, for feedback control I dont see in your diagram tl431 and opto couplers for feedback. Feedback should regulate pulses and not carrier wave.

Thanks for shearing this ideal video. thanks again.

Can I make 5 to 6 pieces and add parallal to increase Ampere...??

I love this video .Can we convert 600 volt DC to ₹220 voltage in a pure sine way with the help of your code of 32 khz frequency? With the help of step down transformer? If possible Please help me

helllo Sir ,May i know how to communicate with you ,any mail id or whats app no ?